Ryobi A25RT02- User Manual

6 SYMBOLS SERVICE Servicing requires extreme care and knowledge and should be performed only by a qualified service technician. For service we suggest you return the product to the nearest AUTHORIZED SERVICE CENTER for repair. When servic- ing, use only identical replacement parts. WARNING: To avoid...

7 ELECTRICAL SPEED AND WIRING The no-load speed of this product depends on the router you are using. This speed is not constant and decreases under a load or with lower voltage. For voltage, the wiring in a shop is as important as the motor’s horsepower rating. A line intended only for lights cannot...

8 Inch 1 0 1 2 3 Inch 1 0 1 2 3 inch FEED DIRECTION 1 Inch FEATURES PRODUCT SPECIFICATIONS Table Dimensions ................................ 16 in. x 32 in. x 1 in.Maximum Cutter Diameter ................................. 1-15/16 in.Fence Length .........................................................

9 FEATURES RESET BUTTON See Figure 2. The router table switch is equipped with a reset button that protects the electronic components of the router table switch box from overload. STARTING PIN When you are unable to use the fence for a guide because the workpiece is odd-shaped or too small, use the ...

10 Inch 1 0 1 2 3 Inch 1 0 1 2 3 FEED DIRECTION 3 ASSEMBLY PACKING LIST 1. Table Leg (4) 2. Starting Pin 3. Table Leg Phillips Head Screw (16) 4. Table Top 5. Switch Box Nut (3) 6. Switch Box Screw (3) 7. Switch Box 8. Carriage Bolt Washer (2) 9. Carriage Bolt (2) 10. Hex Key (1) 11. Under Table Gua...

11 ASSEMBLY ASSEMBLING THE ROUTER TABLE Assembling the router table involves attaching the switch box, the under table guards, the legs, the router/insert plate as-sembly, the fence assembly, featherboard, throat plate, starting pin, and installing the miter gauge to the router table. ATTACHING THE ...

12 ASSEMBLY PRE-DRILLING HOLES FOR THROUGH TABLE DEPTH ADJUSTMENT See Figure 8. Since each router will have different placements for through table depth adjustments, pilot holes have been pre-drilled in the throat plate to assist in through table adjustments. Only the models listed below in the key ...

13 ASSEMBLY BRAND MODEL BASE TYPE FASTENER SIZE INSERT PLATE HOLES USED NUMBER OF HOLES Bosch 1617 Fixed 10-24 x 5/8 in. A1, A3, A5 3 Bosch 1617 EVS Fixed 10-24 x 5/8 in. A1, A3, A5 3 Bosch 1617 EVSPK Fixed 10-24 x 5/8 in. A1, A3, A5 3 Craftsman 17504 Fixed 10-32 x 5/8 in. A2, A4, A6 3 Craftsman 175...

14 MAKING INSERT PLATE LEVEL See Figure 12.  Unplug the router table and/or the router.  Check to see if the insert plate mounted assembly is level with a straight edge or level.  Loosen insert plate screws.  Using the supplied hex key, tighten or loosen the adjust- ing screws depending on how t...

15 Inch 1 0 1 2 3 Inch 1 0 1 2 3 ASSEMBLY Inch 1 0 1 2 3 Inch 1 0 1 2 3 FEED DIRECTION STARTING PIN HOLES STARTING PIN INSTALL REMOVE Fig. 16 SLOT FEATHERBOARD BOLT CARRIAGE BOLT WASHER FENCE LOCK KNOB FEED DIRECTION Inch 1 0 1 2 3 Inch 1 0 1 2 3 Fig. 17 MITER GAUGE SLOT MITER GAUGE BAR POINTER FEAT...

16 Inch 1 0 1 2 3 Inch 1 0 1 2 3 inch Inch 1 0 1 2 3 Inch 1 0 1 2 3 inch FEED DIRECTION 1 Inch ASSEMBLY ATTACHING THE VACUUM HOSE See Figure 18. The vacuum port molded into the fence will accept either a 1-1/4 in. or 2-1/2 in. vacuum attachment. CLAMPING THE ROUTER TABLE TO A WORK BENCH See Figures ...

17 OPERATION PERFORMING A ROUTING OPERATION Observe the following rules when using the router.  Read the entire operator’s manual for the router and router table.  Plug the router table power cord into a power source.  Always control the power to the router with the router table switch whenever t...

18 Inch 1 0 1 2 3 Inch 1 0 1 2 3 FEED DIRECTION 2 3 FEED DIRECTION 1 Inch Inch 1 0 1 2 3 Inch 1 0 1 2 3 OPERATION INSERTING/REMOVING CUTTERS  Unplug the router table and/or the router.  Remove the router/insert plate assembly. (See Installing Router/Insert Plate Assembly in the Assembly section.) ...

19 MAINTENANCE WARNING: Do not at any time let brake fluids, gasoline, petroleum-based products, penetrating oils, etc., come in contact with plastic parts. Chemicals can damage, weaken or destroy plastic which may result in serious personal injury. Electric tools used on fiberglass material, wallbo...

20 OPERATOR’S MANUAL ROUTER TABLE A25RT02 987000-11503-20-07 (REV:01) A25RT02 • PARTS AND SERVICE Prior to requesting service or purchasing replacement parts, please obtain your model and serial number from the product data plate. • MODEL NUMBER • SERIAL NUMBER • HOW TO OBTAIN REPLACEMENT PARTS: Rep...