Ryobi A25RT01- Manual

6 SYMBOLS SERVICE Servicing requires extreme care and knowledge and should be performed only by a qualified service technician. For service we suggest you return the product to the nearest AUTHORIZED SERVICE CENTER for repair. When servic- ing, use only identical replacement parts. WARNING: To avoid...

7 ELECTRICAL SPEED AND WIRING The no-load speed of this product depends on the router you are using. This speed is not constant and decreases under a load or with lower voltage. For voltage, the wiring in a shop is as important as the motor’s horsepower rating. A line intended only for lights cannot...

8 STARTING PIN FEED DIRECTION inch 1 0 1 2 3 Inch 1 0 1 2 3 Inch 1 Inch FEED DIRECTION 1 Fig. 2 FEATURES PRODUCT SPECIFICATIONS Table Dimensions ............................. 14 in. x 28 in. x 3/4 in.Maximum Cutter Diameter ................................. 1-15/16 in.Fence Length .....................

9 FEATURES Fig. 3 SWITCH KEY SWITCH IN LOCKED POSITION SWITCH OFF SWITCH ON WARNING: Always remove the switch key when the tool is not in use and keep it in a safe place. In the event of a power failure, turn the switch OFF ( O ) and remove the key. This action will prevent the tool from accidentall...

10 Inch 1 0 1 2 3 Inch 1 0 1 2 3 FEED DIRECTION 1 2 3 1 2 3 UNPACKING This product requires assembly.  Carefully remove the product and any accessories from the box. Make sure that all items listed in the packing list are included.  Inspect the product carefully to make sure no breakage or damage ...

11 Fig. 7 ASSEMBLY Fig. 5 ASSEMBLING THE ROUTER TABLE Assembling the router table involves attaching the switch box, the under table guards, the legs, the router/insert plate assembly, the fence assembly, throat plate, starting pin, and installing the miter gauge to the router table. ATTACHING THE S...

12 ASSEMBLY PRE-DRILLING HOLES FOR THROUGH TABLE DEPTH ADJUSTMENT See Figure 8. Since each router will have different placements for through table depth adjustments, pilot holes have been pre-drilled in the throat plate to assist in through table adjustments. Only the models listed below in the key ...

13 ASSEMBLY BRAND MODEL BASE TYPE FASTENER SIZE INSERT PLATE HOLES USED NUMBER OF HOLES Bosch 1617 Fixed 10-24 x 5/8 in. A1, A3, A5 3 Bosch 1617 EVS Fixed 10-24 x 5/8 in. A1, A3, A5 3 Bosch 1617 EVSPK Fixed 10-24 x 5/8 in. A1, A3, A5 3 Craftsman 17504 Fixed 10-32 x 5/8 in. A2, A4, A6 3 Craftsman 175...

14 0 Inch 1 2 1 3 0 0 Inch 1 2 1 3 0 FENCE LOCK KNOBS CARRIAGE BOLTS FENCE LOCK KNOB WASHER SLOT Fig. 13 Inch 1 0 1 2 3 Inch 1 0 1 2 3 FEED DIRECTION ASSEMBLY Fig. 12 INSERT PLATE STRAIGHT EDGE ADJUSTING SCREWS HEX KEY CARRIAGE BOLT WASHER FENCE ASSEMBLY MAKING INSERT PLATE LEVEL See Figure 12.  Un...

15 FEED DIRECTION Inch 1 0 1 2 3 Inch 1 0 1 2 3 Inch 1 0 1 2 3 Inch 1 0 1 2 3 FEED DIRECTION Fig. 16 STARTING PIN HOLES STARTING PIN INSTALL REMOVE Fig. 15 ASSEMBLY Fig. 14 Inch 1 0 1 2 3 Inch 1 0 1 2 3 FEED DIRECTION THROAT PLATE NOTCH TAB MITER GAUGE MITER GAUGE BAR POINTER SLOT The proper size th...

16 inch FEED DIRECTION 1 inch 1 VACUUM HOSE VACUUM PORT Inch 1 0 1 2 3 Inch 1 0 1 2 3 FEED DIRECTION Inch 1 0 1 2 3 Inch 1 0 1 2 3 FEED DIRECTION HEX NUT WORK TABLE FLAT WASHER LOCK WASHER ASSEMBLY CLAMP WORK TABLE ATTACHING THE VACUUM HOSE See Figure 17. The vacuum port molded into the fence will a...

17 OPERATION PERFORMING A ROUTING OPERATION Observe the following rules when using the router.  Read the entire operator’s manual for the router and router table.  Plug the router table power cord into a power source.  Always control the power to the router with the router table switch whenever t...

18 1/4 0 Inch 1 0 1 2 3 Inch 1 0 1 2 3 FEED DIRECTION Inch 1 0 1 2 3 Inch 1 0 1 2 3 OPERATION Fig. 20 MITER GAUGE KNOB MITER GAUGE INSERTING/REMOVING CUTTERS  Unplug the router table and/or the router.  Remove the fence assembly. (See Attaching the Fence Assembly in the Assembly section.) LOOSEN C...

19 MAINTENANCE WARNING: Do not at any time let brake fluids, gasoline, petroleum-based products, penetrating oils, etc., come in contact with plastic parts. Chemicals can damage, weaken or destroy plastic which may result in serious personal injury. Electric tools used on fiberglass material, wallbo...

20 OPERATOR’S MANUAL ROUTER TABLE A25RT01 987000-11403-08-07 (REV:00) A25RT01 • PARTS AND SERVICE Prior to requesting service or purchasing replacement parts, please obtain your model and serial number from the product data plate. • MODEL NUMBER • SERIAL NUMBER • HOW TO OBTAIN REPLACEMENT PARTS: Rep...