Ryobi A18MS01- User Manual

Page 2 - RULES FOR SAFE OPERATION; READ ALL INSTRUCTIONS; Keep the work area clean.; Always wear safety glasses with side shields.; TABLE OF CONTENTS

2 3 RULES FOR SAFE OPERATION Safe operation of this accessory requires that you read and understand this operator’s manual, the operator’s manual for the table saw and all labels affixed to the tool. READ ALL INSTRUCTIONS n Know your accessory. Read the operator’s manual carefully. Learn its applica...

Page 3 - SYMBOLS; SYMBOL

2 3 SYMBOLS Some of the following symbols may be used on this tool. Please study them and learn their meaning. Proper interpreta-tion of these symbols will allow you to operate the tool better and safer. Read The Operator’s Manual Safety Alert No Hands Symbol No Hands Symbol No Hands Symbol SYMBOL N...

Page 5 - PREPARING THE STAND; LOCKING; ASSEMBLY; UNPACKING

4 5 Fig. 2 PREPARING THE STAND See Figure 2. n Lay the stand’s top surface down on the floor with the folded legs on top. n Push in a leg locking pin and rotate that leg up until the locking pin clicks into place. n Repeat with the remaining three legs. n Lift the stand and place it in an upright po...

Page 6 - To assemble the work support:; To install the work supports:; ATTACHING SAW MOUNTING BRACKETS

6 7 ASSEMBLING AND INSTALLING MATERIAL WORK SUPPORTS See Figures 3 - 5. The material work supports help balance the workpiece during cutting operations. To assemble the work support: n Slide a carriage bolt (M6 x 60 mm) through the square hole in the work support and extend through the other side. n...

Page 8 - MOUNTING THE MITER SAW TO THE STAND; �To remove saw from stand:

8 9 ASSEMBLY MOUNTING THE MITER SAW TO THE STAND See Figures 8 - 9. Use the handles located at the rear of the mounting brackets to aid in installing or removing saw and bracket assembly. n �Lift the saw and bracket assembly, allowing the assembly to tilt slightly toward your body. n While still til...

Page 9 - LOWER; OPERATION; APPLICATIONS

8 9 Fig. 9 ASSEMBLY � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � LOWER LOCKING LEVERS TO SECURE TO STAND OPERATION WARNING: Do not allow familiarity with tools to make you care-less. Remember tha...

Page 10 - USING THE EXTENSION RAILS; To raise the work stops:

10 11 OPERATION USING THE EXTENSION RAILS See Figure 10. Use the extension rails when working with larger workpieces. To extend the rails: n Loosen the extension adjustment knob. n Extend the rail to the desired position. n Tighten the extension adjustment knob. Fig. 10 USING THE WORK STOPS See Figu...

Page 11 - Installing the workshelf:

10 11 � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � n Insert the 3/4 x 7-1/2 in. plywood strip horizontally be-tween the 6 in. strips, making sure the long edge is flush with the base. n Pre-drill...

Page 12 - MAINTENANCE; GENERAL MAINTENANCE

RYOBI TECHNOLOGIES, INC. 1428 Pearman Dairy Road, Anderson, SC 29625 Post Office Box 1207, Anderson, SC 29622-1207 Phone 1-800-525-2579 www.ryobitools.com 983000-710 5-05 MAINTENANCE To adjust: n Use a wrench to slightly loosen the nut. n Turn the screw with a phillips screwdriver. Rotate clock-wise...

Table of Contents:

Other Manuals for Ryobi A18MS01

Summary

Other Ryobi Models