Page 2 - I. GENERAL OPERATION; SAFETY RULES; Safe Operation Practices for Ride-On Mowers; WARNING
2 I. GENERAL OPERATION • Read, understand, and follow all instructions on the machine and in the manual before starting. • Do not put hands or feet near rotating parts or under the machine. Keep clear of the discharge opening at all times. • Only allow responsible adults, who are familiar with the i...
Page 4 - CUSTOMER RESPONSIBILITIES; TABLE OF CONTENTS; PRODUCT SPECIFICATIONS
4 CONGRATULATIONS on your purchase of a new tractor. It has been designed, engineered and manu fac tured to give you the best possible dependability and performance. Should you experience any problem you cannot easily rem-edy, please contact your nearest authorized service center/department. We have...
Page 5 - UNASSEMBLED PARTS; Steering Wheel
5 UNASSEMBLED PARTS Steering Wheel Steering Wheel Insert (1) Large Flat Washer Steering Boot Seat (2) Keys Slope Sheet Key (1) Oil Drain Tube (1) Knob (1) Washer 17/32 x 1-3/16 x 12 Gauge (1) Hex Bolt 5/16-18 x 4 (1) 5/16 Lock Washer Steering Extension Shaft Steering Wheel Adapter
Page 6 - ASSEMBLY; TOOLS REQUIRED FOR ASSEMBLY; UNPACK CARTON
6 ASSEMBLY TOOLS REQUIRED FOR ASSEMBLY A socket wrench set will make assembly easier. Stan dard wrench sizes are listed.(1) 3/4" wrench Pliers (1) 1/2" wrench Tire pressure gauge Utility knife When right or left hand is mentioned in this man ual, it means when you are in the operating po si ...
Page 7 - TO DRIVE TRAC
7 ASSEMBLY NOTE: You may now roll or drive your tractor off the skid. Follow the ap pro pri ate instruction below to remove the tractor from the skid . TO ROLL TRACTOR OFF SKID (See Op- er a tion section for location and function of con trols) • Press lift lever plunger and raise attachment lift lev...
Page 8 - CHECKLIST
8 CHECK TIRE PRESSURE The tires on your tractor were overinfl ated at the factory for shipping purposes. Correct tire pressure is important for best cutting performance.• Reduce tire pressure to PSI shown in “PRODUCT SPEC I FI CA TIONS” section of this manual. CHECK DECK LEVELNESS For best cutting r...
Page 9 - OPERATION
9 OPERATION These symbols may appear on your tractor or in literature supplied with the product. Learn and understand their mean-ing. DANGER, KEEP HANDS AND FEET AWAY FREE WHEEL (Automatic Models only) OVER TEMP LIGHT KEEP AREA CLEAR SLOPE HAZARDS 15 15 (SEE SAFETY RULES SECTION) BATTERY REVERSE FOR...
Page 10 - KNOW YOUR TRACTOR
10 02871 OPERATION KNOW YOUR TRACTOR READ THIS OWNER'S MANUAL AND SAFETY RULES BEFORE OPERATING YOUR TRACTOR Compare the illustrations with your tractor to familiarize yourself with the locations of various controls and ad just ments. Save this manual for future reference. Our tractors conform to th...
Page 11 - HOW TO USE YOUR TRACTOR
11 OPERATION The operation of any tractor can result in foreign objects thrown into the eyes, which can result in severe eye dam age. Always wear safety glass es or eye shields while op-erating your tractor or per form ing any adjustments or repairs. We rec om mend a wide vision safety mask over spe...
Page 12 - TO OPERATE ON HILLS
12 OPERATION TO OPERATE ON HILLS WARNING: Do not drive up or down hills with slopes greater than 15° and do not drive across any slope. • Choose the slowest speed before starting up or down hills. • Avoid stopping or changing speed on hills.• If slowing is necessary, move throttle control lever to s...
Page 13 - ADD GASOLINE; TOWING CARTS AND OTHER AT TACH MENTS; BEFORE STARTING THE ENGINE; CHECK ENGINE OIL LEVEL
13 ADD GASOLINE • Fill fuel tank to bottom of fi ller neck. Do not overfi ll. Use fresh, clean, regular un lead ed gasoline with a minimum of 87 octane. (Use of leaded gasoline will increase carbon and lead oxide deposits and reduce valve life). Do not mix oil with gasoline. Purchase fuel in quan ti...
Page 14 - MOWING TIPS; PURGE TRANSMISSION
14 FIG. 9 MOWING TIPS • Mower should be properly leveled for best mowing per- formance. See “TO LEVEL MOWER HOUSING” in the Service and Adjustments section of this manual. • The left hand side of mower should be used for trim- ming. • Drive so that clippings are discharged onto the area that has bee...
Page 15 - MAINTENANCE; LUBRICATION CHART; MAINTENANCE SCHEDULE; GENERAL RECOMMENDATIONS; BEFORE EACH USE
15 MAINTENANCE LUBRICATION CHART ➀ FRONT WHEEL BEARING ZERK ➀ FRONT WHEEL BEARING ZERK ➁ ENGINE ➀ SPINDLE ZERK ➀ SPINDLE ZERK ➀ GENERAL PURPOSE GREASE ➁ REFER TO MAINTENANCE “ENGINE” SECTION IMPORTANT: DO NOT OIL OR GREASE THE PIVOT POINTS WHICH HAVE SPECIAL NYLON BEARINGS. VISCOUS LU BRI CANTS WILL...
Page 16 - TRACTOR
16 MAINTENANCE BLADE REMOVAL (See Fig. 10) • Raise mower to highest position to allow access to blades. • Remove blade bolt, lock washer and fl at washer se cur ing blade. • Install new or resharpened blade with trailing edge up towards deck as shown. IMPORTANT: TO ENSURE PROPER ASSEMBLY, CENTER HOL...
Page 17 - TRANSAXLE COOLING; BATTERY; TRANSAXLE PUMP FLUID; ENGINE; LUBRICATION
17 MAINTENANCE V-BELTS Check V-belts for deterioration and wear after 100 hours of operation and replace if necessary. The belts are not ad just able. Re place belts if they begin to slip from wear. TRANSAXLE COOLING The transmission fan and cooling fi ns should be kept clean to assure proper coolin...
Page 18 - CLEANING
18 MAINTENANCE MUFFLER Inspect and replace corroded muffl er and spark arrester (if equipped) as it could create a fi re hazard and/or dam-age. SPARK PLUGS Replace spark plugs at the beginning of each mowing season or after every 100 hours of operation, whichever occurs fi rst. Spark plug type and g...
Page 19 - SERVICE AND ADJUSTMENTS; TO LEVEL MOWER HOUSING
19 SERVICE AND ADJUSTMENTS FIG. 15 TO LEVEL MOWER HOUSING Adjust the mower while tractor is parked on level ground or driveway. Make sure tires are properly infl ated (See “PROD UCT SPECIFICATIONS” section of this manual). If tires are over or underinfl ated, you will not properly adjust your mower....
Page 21 - TRANSAXLE MOTION CONTROL LE; TO CHECK AND ADJUST BRAKE
21 SERVICE AND ADJUSTMENTS TRANSAXLE MOTION CONTROL LE VER NEUTRAL ADJUSTMENT (See Fig. 23) The motion control lever has been pre set at the factory and adjustment should not be necessary.• Loosen adjustment bolt in front of the right rear wheel, and lightly tighten. • Start engine and move motion c...
Page 22 - TO A D
22 FIG. 25 SERVICE AND ADJUSTMENTS TO REMOVE WHEEL FOR REPAIRS (See Fig. 24) • Block up axle securely.• Remove axle cover, retaining ring and washers to allow wheel removal (rear wheel contains a square key - Do not lose). • Repair tire and reassemble.• On rear wheels only: align grooves in rear whe...
Page 24 - STORAGE; FUEL SYSTEM; ENGINE OIL; OTHER
24 STORAGE Immediately prepare your tractor for storage at the end of the season or if the tractor will not be used for 30 days or more. WARNING: Never store the trac tor with gas o line in the tank inside a building where fumes may reach an open fl ame or spark. Allow the engine to cool before stor...
Page 25 - TROUBLESHOOTING POINTS
25 TROUBLESHOOTING POINTS Will not start 1. Out of fuel. 1. Fill fuel tank. 2. Engine not “CHOKED” properly. 2. See “TO START ENGINE” in Operation section. 3. Engine fl ooded. 3. Wait several minutes before attempting to start. 4. Bad spark plug. 4. Replace spark plug. 5. Dirty air fi lter. 5. Clean...
Page 27 - LIMITED WARRANTY
27 LIMITED WARRANTY The Manufacturer warrants to the original consumer purchaser that this product as manufactured is free from defects in materi-als and work man ship. For a period of two (2) years from date of purchase by the original consumer purchaser, we will repair or replace, at our option, w...
Page 28 - SERVICE NOTES
Page 29 - SUGGESTED GUIDE FOR SIGHTING SLOPES FOR SAFE OPERATION
29 15 DEGREES MAX. FOLD ALONG DO TTED LINE THIS IS A 15 DEGREE SLOPE ONLY RIDE UP AND DOWN HILL,NOT ACROSS HILL SUGGESTED GUIDE FOR SIGHTING SLOPES FOR SAFE OPERATION WARNING: To avoid serious injury, operate your tractor up and down the face of slopes, never across the face. Do not mowslopes greate...
Page 30 - PARTS AND SERVICE
This product has been expertly en gi neered and carefully manu fac tured to rigid quality stan dards. As with all mechanical products, some adjustments or part replacement may be necessary during the life of your unit. For Parts and service, contact our authorized distributor: call 1-800-849-1297 • ...
