Runco VHD-4402 - Manual

Congratulations on your purchase of the VHD-4402 ULTRA! This processor is designed to work with either a CRT projector or a fixed-pixel device (DLP, Plasma, etc.), and will provide full aspect ratio con- trol as well as greatly enhanced picture quality. For example, DLP projectors were not initially...

7 FRONT AND REAR PANEL DESCRIPTIONS Front Panel M U L T I F I L M Menu 4402 ULTRA 1 2 3 4 5 7 8 6 9 R UN C O 1. IR RECEIVER Receives the IR commands from the remote control. 2. MENU BUTTON The MENU button brings up the main adjustment menu. After making adjustments, the MENU button will bring you ba...

8 1. 12v Fuse This fuse protects the 12v outputs from the MASK and SCREEN jacks.(Screen Fuse: 5mm x 25mm, AGC, 1A, 250v, Fast Blow) 2. Mask This is a 12V output that is used to trigger masking on screens that have that capability (For use on motorized screens only). 3. Screen This is a 12V output th...

While there are many different ways to connect your source equipment to your VHD-4402 ULTRA, the examples shown above are the most common and are recommended by Runco. • COMPOSITE VIDEO INPUT: Composite video is the most common type of signal used, but is also the lowest in picture quality. Many sou...

12 To get started using your VHD-4402 ULTRA and projector, follow these simple steps: 1. Ensure all sources that you are using are properly connected to the VHD-4402 ULTRA. This is something your Runco dealer has probably already done for you; if not, please refer to the ‘Connection Examples’ and th...

13 QUICK SET-UP GUIDE Overall Functional Description The VHD-4402 ULTRA’s purpose is twofold. First, it provides aspect ratio control and can do so on either a WIDESCREEN or a standard 4:3 screen. Second, it pro- vides a clean, progressive signal to the projector. The processing the VHD-4402 ULTRA u...

14 The main menu (shown above) includes two sections: Source Selection/ Picture quality adjustments and Functional adjustments. Pressing MENU on the front panel or on the remote control will bring up the main menu. In the menu shown above, Composite video is selected as the current source. This is i...

Aspect Ratio allows selection of one of the three aspect ratios provided by the processor. You have two options for selecting an aspect ratio: First, highlight ASPECT RATIO on the main menu, then press ENTER. Then select the desired aspect ratio, and again press ENTER. The second option is to simply...

18 An ‘aspect ratio’ is simply the ratio of the width vs. the height of the screen. For example, the current aspect ratio standard is 4:3 (or 1.33:1), where the image is 4 units wide and 3 units tall. ASPECT RATIOS First, the Basics 4 units wide 3 units tall All of our ‘regular’ televisions are this...

M U L T I F I L M Menu 4402 ULTRA 12v Fuse Mask Screen RS-232 IN V H B G R Pass-through Pb Pr Y R UNCO RS-232 OUT S-VIDEO COMPOSITE 3.5" 17.45" 17" 17.45" 17" 16" 3.5" 16" R UN C O 3.5" 20 DIMENSIONS Front Panel Side Rear Panel Top

RS-232 PROTOCOL 9600 Baud8 bitsNo parity1 Stop bit ASCII RxD of the PC or TxD of the VHD is on pin2TxD of the PC or RxD of the VHD is on pin3Gnd is pin 5RTS of the PC or CTS of the VHD is on pin7 (not used)CTS of the PC or RTS of the VHD in on pin8 (not used) Command format <input><aspect r...

22 Inputs: (1) Component, (1) S-video, (1) Composite, (1) Pass-through Input standards: NTSC (PAL, NTSC export version) Output formats: 540p, 600p (38 khz) Bandwidth: Video inputs: 5.5 MhzPass-through: 100 Mhz Power input: 120V (220V export model), 50/60 Hz Power consumption: 15W Control Options: RS...