Page 3 - LIMITED WARRANTY
LIMITED WARRANTY Copyright Rose Electronics 2002. All rights reserved. No part of this manual may be reproduced, stored in a retrieval system, or transcribed in any form or any means, electronic or mechanical, including photocopying and recording, without the prior written permission of Rose Elect...
Page 4 - FCC/IC STATEMENTS, EU DECLARATION OF CONFORMITY; FEDERAL COMMUNICATIONS COMMISSION
FCC/IC STATEMENTS, EU DECLARATION OF CONFORMITY FEDERAL COMMUNICATIONS COMMISSION AND INDUSTRY CANADA RADIO-FREQUENCY INTERFERENCE STATEMENTS Models: CRK-2DFMPD1D CRK-2DFMPD2D CRK-2DFMUD1D CRK-2DFMUD2D CRK-2DFSPD1D CRK-2DFSUD1D CRK-2DFSPD2D CRK-2DFSUD2D This equipment generates, uses and can radiate...
Page 5 - TABLE OF CONTENTS; Contents
TABLE OF CONTENTS Contents Disclaimer ......................................................................................................... 2 System introduction .......................................................................................... 2 Features ...................................
Page 6 - INTRODUCTION; Disclaimer; Thank you for choosing the Rose Electronics
INTRODUCTION 2 CRYSTALVIEW DVI FIBER INSTALLATION AND OPERATIONS MANUAL Disclaimer While every precaution has been taken in the preparation of this manual, the manufacturer assumes no responsibility for errors or omissions. Neither does the manufacturer assume any liability for damages resulting fro...
Page 7 - Features; DDC Information; Package contents
CRYSTALVIEW DVI FIBER INSTALLATION AND OPERATIONS MANUAL 3 Features Perfect image quality at resolutions up to 1920 x 1200 @ 60Hz using fiber optic cable over all allowed distances, all lower resolutions with refresh rates of at least 75Hz Extend a KVM station from a CPU up to 33,000 feet (10,00...
Page 8 - MODELS
MODELS 4 CRYSTALVIEW DVI FIBER INSTALLATION AND OPERATIONS MANUAL Models / Connectors (Single Video) PS/2 Transmitter (2-DVI-I / 1-MiniDin6 – “Y” cable needed) PS/2 Receiver (1-DVI-I / 2-MiniDin6) USB Transmitter (2-DVI-I / 1-USB type B) USB Receiver (1-DVI-I / 2-USB type A) Transmitter / Receiver (...
Page 9 - USB Transmitter
CRYSTALVIEW DVI FIBER INSTALLATION AND OPERATIONS MANUAL 5 Models / Connectors (Single Video – Serial / Audio) PS/2 Transmitter (2-DVI-I / 1-MiniDin6 – “Y” cable needed) PS/2 Receiver (1-DVI-I / 2-MiniDin6) USB Transmitter (2-DVI-I / 1-USB type B) USB Receiver (1-DVI-I / 2-USB type A) Transmitter / ...
Page 10 - REAR
6 CRYSTALVIEW DVI FIBER INSTALLATION AND OPERATIONS MANUAL Models (Dual Video) REAR FRONT PS/2 Transmitter (4-DVI-I / 1-MiniDin6) ”Y” cable needed PS/2 Receiver (2-DVI-I / 2-MiniDin6) USB Transmitter (4-DVI-I / 1-USB Type B) USB Receiver (2-DVI-I / 2-USB Type A) Transmitter (Front-All) (1-Power / 2-...
Page 12 - Cables; (See Attachment B for cable part numbers); CrystalView DVI Fiber to PC cable
8 CRYSTALVIEW DVI FIBER INSTALLATION AND OPERATIONS MANUAL Cables (See Attachment B for cable part numbers) Transmitter unit to CPU cable CPU cables connect from the transmitter to a CPUs keyboard, video monitor and mouse ports. A “Y” PS/2 cable for the keyboard and mouse are needed. Receiver to KVM...
Page 13 - INSTALLATION; Installation; Figure 1. Typical cabling configurations
INSTALLATION CRYSTALVIEW DVI FIBER INSTALLATION AND OPERATIONS MANUAL 9 Installation Please refer to the safety section first before proceeding with any installation or configuration of the CrystalView DVI Fiber. When installing the CrystalView DVI Fiber, locate the transmitter as close as possible ...
Page 14 - Transmitter to Receiver cabling; Maximum distance; Table 1.Transmitter to receiver cabling; Applying power
10 CRYSTALVIEW DVI FIBER INSTALLATION AND OPERATIONS MANUAL Transmitter to Receiver cabling Cable type (w/ LC connectors) Maximum distance 62,5µm Multimode-Fiber 650 ft / 200 m 50.0µm Multimode-Fiber 1300ft / 400m 9.0µm Singlemode-Fiber 33,000ft / 10,000m Table 1.Transmitter to receiver cabling Appl...
Page 15 - Diagnostic LED Indicators; Off – No power applied, device not ready
CRYSTALVIEW DVI FIBER INSTALLATION AND OPERATIONS MANUAL 11 Diagnostic LED Indicators Power (Red) Off – No power applied, device not ready On- Power applied, device ready Data Error (Green) • Off - No errors, device ready • Blinking / On – Transmitter / Receiver communication not established Lin...
Page 16 - OPERATION; Operating instructions
OPERATION 12 CRYSTALVIEW DVI FIBER INSTALLATION AND OPERATIONS MANUAL Operating instructions Operation of your computer is no different than having your keyboard, monitor, and mouse connected directly to the computer. All functions, applications, upgrades and other items can be done normally. The on...
Page 17 - DDC Source
CRYSTALVIEW DVI FIBER INSTALLATION AND OPERATIONS MANUAL 13 Carefully remove the four (4) Phillips screws from the bottom of the unit. If your model is a dual version, also remove the UNC screws that secure the video connectors. A- Remove the top cover exposing the internal PC board as shown below B...
Page 18 - (Turn on the remote monitor power if power is off); Reset DDC table to default values; second upon successful re-programming of the default DDC values; Color Depth Selection; Color Depth
14 CRYSTALVIEW DVI FIBER INSTALLATION AND OPERATIONS MANUAL 5. Wait until the STATUS LINK LED illuminates 6. Connect the remote monitor’s video cable to the remote unit. (Turn on the remote monitor power if power is off) 7. The remote monitor’s DDC information will be read automatically, transferred...
Page 19 - Selecting moment of switching to next frame; Moment to switch JP3 Description
CRYSTALVIEW DVI FIBER INSTALLATION AND OPERATIONS MANUAL 15 Selecting moment of switching to next frame Normally the transmission of screen data is terminated when a frame is displayed on the screen. If the video source switches to a new frame during this display period, horizontal screen breaks may...
Page 20 - TROUBLESHOOTING; Troubleshooting; There isn’t a picture.
TROUBLESHOOTING 16 CRYSTALVIEW DVI FIBER INSTALLATION AND OPERATIONS MANUAL Troubleshooting The troubleshooting section is used as a guide to understanding the capabilities of the CrystalView DVI Fiber and for general troubleshooting. If you have any problems or questions concerning the installation...
Page 21 - SERVIDE; Service Information; Maintenance and Repair; Rose Electronics; Technical Support
SERVIDE CRYSTALVIEW DVI FIBER INSTALLATION AND OPERATIONS MANUAL 17 Service Information Maintenance and Repair This Unit does not contain any internal user-serviceable parts. In the event a Unit needs repair or maintenance, you must first obtain a Return Authorization (RA) number from Rose Electroni...
Page 22 - SAFETY; Safety
SAFETY 18 CRYSTALVIEW DVI FIBER INSTALLATION AND OPERATIONS MANUAL Safety The CrystalView DVI Fiber KVM extender has been tested for conformance to safety regulations and requirements, and has been certified for international use. Like all electronic equipment, the CrystalView DVI Fiber should be us...
Page 23 - Safety and EMC Regulatory Statements; documentation to get more information about the product.; WARNING
CRYSTALVIEW DVI FIBER INSTALLATION AND OPERATIONS MANUAL 19 Safety and EMC Regulatory Statements Safety information Documentation reference symbol. If the product is marked with this symbol, refer to the product documentation to get more information about the product. WARNING A W ARNING in the manua...
Page 24 - APPENDICES; Appendix A. General specifications; Power adapter
APPENDICES 20 CRYSTALVIEW DVI FIBER INSTALLATION AND OPERATIONS MANUAL Appendix A. General specifications Maximum resolution 1920 x 1200 @ 60Hz over all allowed distances all lower resolutions with refresh rates of at least 75Hz Video compatibility DVI-D Keyboard PS/2 or USB Mouse PS/2 or USB Power ...
Page 25 - Appendix B. Parts and cables; Rackmount kit; Description
CRYSTALVIEW DVI FIBER INSTALLATION AND OPERATIONS MANUAL 21 Appendix B. Parts and cables Part Number (Multimode) Description CRV-DLDFMPD1D DVI-D / PS/2 Single video (Transmitter) CRV-SRDFMPD1D DVI-D / PS/2 Single video (Receiver) CRV-DLDFMPD2D DVI-D / PS/2 Dual video (Transmitter) CRV-SRDFMPD2D DVI-...
Page 26 - Appendix C. Rackmount Kit
Appendix C. Rackmount Kit Rack mounting the CrystalView DVI Fiber uses the rackmount kit part number RM-BR3. You can mount 1 to 4 units on a single shelf and mount the shelf in a standard 19” rack. The units can be orientated on the rack with either the front or rear panel facing to the front or rea...
