Rose Electronics CTP-8S - Manual

Rose Electronics CTP-8S

Rose Electronics CTP-8S – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.

1 Page 1
2 Page 2
3 Page 3
4 Page 4
5 Page 5
6 Page 6
7 Page 7
8 Page 8
9 Page 9
10 Page 10
11 Page 11
12 Page 12
13 Page 13
14 Page 14
15 Page 15
16 Page 16
17 Page 17
18 Page 18
19 Page 19
20 Page 20
21 Page 21
22 Page 22
23 Page 23
24 Page 24
25 Page 25
26 Page 26
27 Page 27
28 Page 28
29 Page 29
30 Page 30
31 Page 31
32 Page 32
33 Page 33
34 Page 34
35 Page 35
36 Page 36
37 Page 37
38 Page 38
39 Page 39
40 Page 40
Page: / 40

Table of Contents:

  • Page 3 – Limited Warranty
  • Page 4 – Table of Contents; Contents
  • Page 5 – Introduction; Disclaimer
  • Page 6 – Model Number and Options; First Steps; additional cables they usually arrive in the same package.
  • Page 7 – FRONT PANEL DISPLAY; Caretaker Plus Front Panel Display; is lit whenever the unit is powered on.
  • Page 8 – QUICK SETUP LIST – Serial Units; Serial Set-Up for PCs
  • Page 9 – Caretaker Plus Rear Panel – Serial Model
  • Page 10 – QUICK SETUP LIST – Parallel Units; your computers to ports 1-8 with the correct cables.; Caretaker Plus Rear Panel – Parallel Model
  • Page 11 – CABLING; Parallel Cabling; to your specified length.; Serial Cabling; CONFIGURATION
  • Page 12 – Table 1. Configuration Menu Display
  • Page 13 – Configuration Menu Items; from the user is shown in underlined courier type.; Protocol; changes are made when you exit the configuration menu.; Timeout; prompt and enter the new timeout value.
  • Page 14 – Form Feed; custom configuration.; Keep
  • Page 15 – Exit
  • Page 16 – Reverse Channel Data Timeout; reverse channel data timeout.; Filter Characters
  • Page 17 – Configuration Commands
  • Page 18 – Protocol Command
  • Page 19 – Parallel Enable Logic Command; other than Y or N is used no action is taken.; Initialization String Command; following a NULL will be ignored.; Grounding; disconnect the power cord until the ground has been restored.
  • Page 20 – OPERATIONS; Initial State
  • Page 21 – Buffer Characteristics; Printer Initialization Signal (Parallel Models Only)
  • Page 23 – Initialization String
  • Page 24 – Power Up Initial Display; Program Checksum Test
  • Page 25 – Static Ram Read/Write Test
  • Page 26 – Flow Control Display Mode (Serial Models Only); status of the shared device's input buffer.
  • Page 27 – TROUBLESHOOTING; Troubleshooting; Common Problems and Solutions
  • Page 29 – Maintenance and Repair; Technical Support representative.
  • Page 30 – DIAGNOSTICS; Diagnostic Modes
  • Page 31 – Print Configuration/Test Pattern Function; Serial Units
  • Page 32 – Long Test Without Loopback; - EPROM program checksum test is the same as described previously.; Test 3; - Same as static ram read/write test above; Test 6; advance and the select switches may be pressed.
  • Page 33 – Long Test with Loopback; Table 9. Loopback Test Connectors
  • Page 34 – APPENDICES; Appendix A: Serial Cabling; Other Devices
  • Page 35 – Appendix B: Pinout Specifications; Serial Models; Pin; Parallel Models
  • Page 36 – Appendix C: MP1000 Memory Board; About the Board; during installation.; Installation; Opening the Caretaker Plus
  • Page 37 – Installing the Board; tighten the spacers for each board.; Adding Chips to an Empty Board or Adding Additional Chips; To obtain 2MB an additional board must be installed.; Verification of Installation
  • Page 38 – Appendix D: Factory Defaults
Loading the manual

10707 Stancliff Road Houston, Texas 77099

Phone: (281) 933-7673 Internet: WWW.ROSE.COM

INSTALLATION

AND

OPERATIONS MANUAL

"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.

Summary

Page 3 - Limited Warranty

Limited Warranty Copyright  Rose Electronics 1990-2002. All rights reserved. No part of this manual may be reproduced, stored in a retrieval system, or transcribed in any form or any means, electronic or mechanical, including photocopying and recording, without the prior written permission of Rose ...

Page 4 - Table of Contents; Contents

Table of Contents Contents Disclaimer .................................................................................................................... 1 Introduction .................................................................................................................. 1 Features .......

Page 5 - Introduction; Disclaimer

Introduction CARETAKER PLUS INSTALLATION AND OPERATIONS MANUAL 1 Disclaimer While every precaution has been taken in the preparation of this manual, the manufacturer assumes no responsibility for errors or omissions. Neither does the manufacturer assume any liability for damages resulting from the u...

Other Rose Electronics Models

All Rose Electronics Other