Rolls RM83T - Manual
Rolls RM83T – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.
RM83T
Eight Channel Mic Mixer
Start Guide
ROLLS CORPORATION
SALT LAKE CITY, UTAH
4/11
pwr
+20
LEVEL
TONE
LEVEL
LEVEL
LEVEL
LEVEL
LEVEL
LEVEL
0 10
LEVEL
1
TONE
2
TONE
3
TONE
4
TONE
5
TONE
6
TONE
7
TONE
LEVEL
8
MASTER
+20
+20
+20
+20
+20
+20
+20
1/8”
STEREO
INPUT
MADE IN USA
www.rolls.com
RM83T
TRANS BALANCED
MIC MIXER
75889 0 0 8 3 0
6
2
SPECIFICATIONS
Input Impedance:
Mic:
600 Ω XLR balanced
1/4":
10K
Ω
unbalanced
Bus Input:
10K Ω unbalanced
Max Input Level:
Mic:
+4 dBV balanced
Line:
+22
dBV
Input Connectors:
8: XLR, 8: 1/4" (Line), 1: RCA (Bus input)
Outputs:
XLR bal., RCA unbalanced Prefade out
Max
Gain: Mic:
60
dB
Line:
35
dB
Tone
Control:
12
dB
Treble/Bass
cut
Phantom
Power:
+48
VDC
Output
Level:
+22
dBV
max
Output
Impedance: 51
Ω
Phase Shift:
<10 degrees, 20Hz to 20 kHz
Max
S/N
ratio:
106
dB
THD:
<.01%
CMRR:
>120
dB
(Mic)
Size:
19"
x
1.75"
x
6"
(48.3
x
4.5
x
15
cm)
Weight:
6
lbs.
DIP SWITCH DEFAULT SETTING:
ALL OFF
JUMPER DEFAULT SETTING:
1/4” JACKS AS INPUT
OPERATION
CONFIGURING THE 1/4” INPUT JACKS AS DIRECT OUTPUTS
The eight 1/4” Input jacks come from the factory confi gured as line inputs and
are electrically mixed with the XLR jacks. They may be used together if desired.
To confi gure a channel’s 1/4” jack as a Direct Out, fi rst remove the RM83T lid.
For each channel there are dual three-pin headers with shorting jumper on two
pins. The setting from the factory is on “IN”. By moving the shorting jumpers to
the confi guration shown as “OUT” (one jumper up, the other down), the jack then
becomes a Direct Output.
CONFIGURING THE 1/4” INPUT JACKS AS INSERTS
To confi gure a channel’s 1/4” jack as an Insert, fi rst remove the RM83T lid and
locate the corresponding channel’s dual three-pin header. Move both shorting
jumpers down as shown below as “INSRT”, the jack then becomes an Insert.
Direct
Output
Insert
Input
CONFIGURING THE OUTPUT FOR MIC OR LINE LEVEL
The RM83T ships from the factory with the XLR Main Output confi gured as Line
Level (+4 dB). To change this to Mic Level (-10 dB), carefully remove the lid,
locate the Mic/Line header which is near the Main Output jack. Move the two
jumpers from the Line Level position (shown below on the right), to the Mic Level
position (shown on the left).
Mic
Level
Line
Level
JUMPER DEFAULTS
The internal jumpers are confi gured from the factory as follows:
1/4” = INPUTS
MAIN OUT LEVEL = LINE LEVEL
"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.
