RocketFish RF-TVMFM03 - Manual

1 Install the TV brackets

Option 1: Installing for a flat mounting surface

1

Align the TV brackets (A and B) with the screw holes on the back of the TV.

2

Place the M4/M5 washers (H) or M6/M8 washers (O) over the holes in the TV brackets that

align with the screw holes on the back of the TV, then insert the M4 screws (F), M5 screws (J),

M6 screws (L or M), or M8 screws (Q) through the washers.

3

Tighten the screws until they are snug against the TV bracket. Do not over tighten.

2 Add the horizontal bars

1

Slide the horizontal bars (C) through the wire guides on the TV brackets.

2

Secure the bars to the TV brackets using the 9/16 in. × 8/32 in. Phillips head screws (W ).

Option 2: Installing for an obstructed mounting surface

Note:

Use additional washers (H) with M4/M5 hardware only.

1

Place the M4/M5 spacers (I) or M6/M8 spacers (P) and the M4/M5 washers (H) into the

recessed screw holes on the back of the TV.

2

Align the TV brackets (A and B) with the spacers and washers on the back of the TV.

3

Place the M4/M5 washers (H) or M6/M8 washers (O) over the holes in the TV brackets that

align with the screw holes on the back of the TV, then insert the M4 screws (G), M5 screws (K),

M6 screws (N), or M8 screws (R or S) through the washers.

4

Tighten the screws until they are snug against the TV bracket. Do not over tighten.

QUICK SETUP GUIDE

RF-TVMFM03

Tools you will need:

• Stud

finder

• Awl
• Pencil
• Level
• Tape

measure

• Phillips

screwdriver

• Socket

wrench

with

1/2 in. socket or

adjustable

wrench

•

7/32 in. wood drill bit

• Power

drill

Package contents

A

Right vertical TV bracket (1)

B

Left vertical TV bracket (1)

C

Horizontal TV bracket (2)

D

Arm assembly (1)

E

Wall plate (1)

M4 bag

F

M4 × 12 mm screws (4)

G

M4 × 30 mm screws (4)

H

M4/M5 washers (8)

I

M4/M5 spacers (4)

M5 bag

J

M5 × 12 mm screws (4)

K

M5 × 30 mm screws (4)

M6 bag

L

M6 × 12 mm screws (4)

M

M6 × 20 mm screws (4)

N

M6 × 35 mm screws (4)

O

M6/M8 washers (4)

P

M6/M8 spacers (4)

Thank you for choosing the Rocketfish RF-TVMFM03.
The RF-TVMFM03 TV mount is designed to support a
flat-panel TV weighing up to 130 lbs. (58.9 kg).

M8 bag

Q

M8 × 16 mm screws (4)

R

M8 × 40 mm screws (4)

S

M8 × 60 mm screws (4)

Hex key bag

T

3/16 in. hex key (1)

Lag bolt bag

U

Lag bolt washer (4)

V

5/16 in. × 2-3/4 in. lag bolt (4)

Bracket hardware

W

9/16 in. × 8/32 in. Phillips head screw (4)

X

3/8 in. × 8/32 in. Phillips head screw (1)

Cable ties

Y

8 in. nylon cable ties (5)

Cap screws

Z

5/32 in. hex key (1)

AA

Cap screws (2)

A

B

C

D

E

M4 bag

Cap screws with hex key

M5 bag

M6 bag

Bracket hardware

M8 bag

Hex key bag

Cable ties

Lag bolt bag

M4

×

12 mm

F

M4

×

30 mm

G

M5

×

12 mm

J

K

M8

×

16 mm

Q

M8

×

40 mm

R

M8

×

60 mm

S

M6/M8

P

M4/M5

I

M6/M8

O

M4/M5

H

T

Y

M6

×

12 mm

L

M6

×

20 mm

M

M6

×

35 mm

N

W

X

AA

V

U

Z

M5

×

30 mm

5/32 in.

5/16 in. × 2-3/4 in.

3/16 in.

3 Install the wall plate to a wood stud wall

Note

: Any material covering the wall must not exceed 5/8 in. (16 mm).

1

Locate the studs. Verify the center of the stud with an awl

or thin nail or use an edge-to-edge stud finder.

2

Level the wall plate (E) and mark the hole locations.

3

Drill pilot hole to a depth of 3 in. using a 7/32 in. diameter drill bit.

4

Align the wall plate (E) with the pilot holes.

5

Place the washers (U) over the holes in the wall plate (E),

insert the lag bolts (V ) through the washers, then tighten

the lag bolts only until the washers (U) are pulled firmly

against the wall plate.

CAUTION

: Avoid potential

injuries or property damage!
DO NOT over-tighten
the lag bolts (V ).

10-1/5 in.

7 in.

TV shifts 7 in. from the home position to
full extension.

16 in.

<5/8 in.

Note

: Intended for use on

wood stud walls with 16 in.
or less spacing only.

R

or

or

or

or

or

(75 mm)

3 in.

Wall

TV

C

M

Y

CM

MY

CY

CMY

K

RF-TVMFM03_10-0726_QSG_V2_EN.eps 1 7/2/2010 1:18:59 PM

RF-TVMFM03_10-0726_QSG_V2_EN.eps 1 7/2/2010 1:18:59 PM

V2

FINAL

FOR PRINT