ROBERTS R737 - Manual - manualsarea.com

Page 2 - Liquid crystal display

Controls (top panel) STANDBY S T FM MHz 2 1 4 3 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 16. FM button 17. MW button 18. LW button 19. Preset buttons 20. + 5 button 21. Standby switch 11. Liquid crystal display 12. Tuning up button 13. Telescopic aerial 14. Power button 15. Tuning down button 6...

Page 3 - Liquid crystal display; MHz; a. Waveband indicator

Controls (LH end) PU9-B INPUT 240V 50Hz OUTPUT 9V 300mA - + DC 9V PIN -ve 22 Liquid crystal display 22.DC Socket STANDBY S T MHz kHz FM MW LW M a b c d e f a. Waveband indicator b. Stereo indicator c. Memory indicator d. Low battery indicator e. Sleep time indicator f. Standby indicator 2

Page 4 - The telescopic aerial is inoperative on MW and LW.; Headphones

General Do not allow this unit to be exposed to water, steam or sand. Do not leavethe unit where excessive heat could cause damage such as in a parked carwhere the heat from the sun can build up even though the outsidetemperature may not seem too high. It is recommended that the FM bandbe used were ...

Page 5 - Setting the clock; Ensure the batteries are fitted and the power switch (14) is off.; Search tuning

Setting the clock Ensure the batteries are fitted and the power switch (14) is off. Press and hold the mode button (5) until the display starts to flash. Releasethe mode button. You now have 5 seconds to start the next procedureotherwise the display will stop flashing and return to showing normal ti...

Page 6 - Memory tuning; Tune in the desired station as previously described.; To recall a station from preset memory

Memory tuning You may store up to 25 stations in memory. 10 on FM, 10 on medium waveand 5 on long wave. Tune in the desired station as previously described. Press the memory button (8) to open the memory a flashing 'M' will appearin the display. While the 'M' is flashing press one of the preset butt...

Page 7 - Setting the standby time; Waking up to the bleeper

Setting the standby time Ensure that the receiver is switched off. Press the mode button (5) once,the STANDBY symbol in the display will start to flash. Press and hold down the mode button (5) until the STANDBY symbol and the time shown in the display begin to flash. Release the mode button. You now...

Page 8 - Sleep timer; symbol in the display.; Low battery indicator; Note: FM stereo is only available via the headphone socket.; L i g h t

Sleep timer The R737 has a built in sleep timer which will automatically switch off thereceiver after the preset time has elapsed. Switch on the receiver and select the required station. Press and holddown the sleep button (7) the timer will count down from 90 minutes in 10minute steps. Release the ...

Page 9 - Specifications; Power Requirements; Circuit Features

Specifications Power Requirements 9.0V Batteries 6 x IEC R14 (C size) Battery Life Approx. 60 hrs. of listening for 4 hours a day atnormal volume using alkaline cells. Frequency Coverage FM87.5 -108M Hz MW 522 - 1620kHz LW 144 - 281kHz Circuit Features Loudspeaker 100mm 8 ohms Output Power 1 watt in...

Page 11 - Guarantee; The guarantee does not cover:

Guarantee This instrument is guaranteed for twelve months from the date of delivery to the original owner against failure due to faulty workmanship or componentbreakdown, subject to the procedure stated below. Should any component or part fail during this guarantee period it will be repaired or repl...

Page 12 - ROBERTS RADIO TECHNICAL SERVICES DEPARTMENT; Isleworth Middlesex; Issue 5

ROBERTS RADIO TECHNICAL SERVICES DEPARTMENT 97-99 Worton Road Isleworth Middlesex TW7 6EG Technical Helpline:- 020 8758 0338 (Mon-Fri during office hours) Issue 5

ROBERTS R737 - Manual

Table of Contents:

Summary

Other ROBERTS Models