Page 2 - Safety Information; CAUTION
Safety Information i DANGER! Avoid Powerlines! When following the instructions in this guide to install and connect thesatellite antenna and connections, take extreme care to avoid contactwith overhead power lines, lights and power circuits. Contact with powerlines, lights, and power circuits may be...
Page 3 - Table of Contents
1 Table of Contents 3 First Things First .............................................................. 3 An Introduction ................................................................................ 3 Installation Overview ....................................................................... 4...
Page 4 - Running Cable into the House and Connecting to the Receiver 70
2 Table of Contents Testing the System ......................................................... 33 Setting Up the Temporary Stand and selecting a site .................. 34 Assembling the Test Components ................................................. 34 Picking Up the Satellite Signal .............
Page 5 - First Things First; An Introduction; Hi, my name is Mark and I wrote this DSS; Some Indoor Stuff
3 First Things First 3 An Introduction Hi, my name is Mark and I wrote this DSS ® System Installation Manual. You probably weren’t expectinga personal introduction, but then, this digitalsatellite system was designed to give you more thanyou expected. Installing the dish isn’t too complicated, but y...
Page 6 - Installation Overview; And The Rest Of The Manual?
4 First Things First Installation Overview The manual is organized into sections that need to be performedin the order they are presented. First Things First. This chapter gives you the information you’ll need to find out whether you really want to tackle the DSS ® System installation yourself. You’...
Page 7 - YES; Second Big Question: Do I Have a Clear; NO; General Site Survey
5 First Things First The First Big Question: Should I DoThis Myself? While the installation is not difficult, it does require that you havesome experience in electrical wiring and minor constructiontechniques. Also, you may have to climb a ladder, so you’ll want tobe comfortable working with heights...
Page 8 - How High Up in the Sky is the Satellite?
6 First Things First First Things First Where Is The Satellite, Anyway? The satellite is always located south of Texas. That means if youlive in Miami, you must have a clear line of sight to thesouthwest; if you live in San Francisco, you must have a clear lineto the southeast. How High Up in the Sk...
Page 9 - Unpack and Take Inventory
7 First Things First First Things First Unpack and Take Inventory Verify that the DSS ® dish box contains these parts: • mounting foot and mast assembly • satellite dish • LNB (Low Noise Block converter) • LNB support arm • hardware packet 1 Phillips head screw 1 Retainer nut LNB Mounting Hardware 4...
Page 10 - Start Putting The Dish Together
8 First Things First Start Putting The Dish Together You won’t completely assemble the dish in this section, but youwill begin the assembly procedure. 1. Locate the satellite dish, the four self-locking nuts and fourstar washers that came in the hardware packet. 2. Place the dish on the LNB support ...
Page 11 - What ’s To Do Indoors?; First, you’ll connect the DSS; Some Outdoor Stuff
9 Some Indoor Stuff What ’s To Do Indoors? A fine question. Well, there are a few tasks you need toaccomplish before you can go outside and install thedish. First, you’ll connect the DSS ® receiver to your TV. One of the four connections scenarios shown should matchyour system. Then, you’ll work on ...
Page 12 - Connecting the DSS; Jacks and Cables
10 Some Indoor Stuff Connecting the DSS ® Receiver You’ll need to connect your DSS ® receiver to your TV and use the on-screen menu system to find the dish pointing coordinates foryour location. The following pages show four preferred methods of connectingthe DSS ® receiver to your TV. These connect...
Page 13 - Choosing a Connection
11 Some Indoor Stuff Choosing a Connection The following pages show four examples of hookups commonlyused to connect the DSS ® receiver with a TV and other components. Refer to your TV and VCR Owner’s Manuals formore information on hooking up your specific components. Connection A Provides the best ...
Page 14 - Connection A; Best Picture and Sound Quality; dish to
12 Some Indoor Stuff Connection A Best Picture and Sound Quality To use this connection you must have: • TV with separate RF, audio/video, and S-Video inputs (jacks) • VCR with RF input and output • Coaxial, audio/video, and S-Video cables To connect TV, VCR and antenna or cable box. 1. Connect coax...
Page 16 - Connection B; Very Good Picture and Sound Quality
14 Some Indoor Stuff Connection B Very Good Picture and Sound Quality To use this connection you must have: • TV with separate RF and audio/video inputs (jacks) • VCR with RF input and output • Coaxial and audio/video cables To connect TV, VCR and antenna or cable box. 1. Connect coaxial cables as s...
Page 18 - Connection C; Good Picture and Sound Quality
16 Some Indoor Stuff Connection C Good Picture and Sound Quality To use this connection you must have: • TV with RF input (jack) • VCR with RF and audio/video inputs • Coaxial and audio/video cables To connect TV, VCR, and antenna or cable box. 1. Connect coaxial cables and audio/video cables as sho...
Page 20 - Connection D; dish to the Satellite In jack
18 Some Indoor Stuff Connection D Good Picture and Sound Quality To use this connection you must have: • TV with RF input • Coaxial cables To connect TV and antenna or cable box: 1. Connect coaxial cables as shown. To receive DSS ® programming: • Tune TV to channel 3 or 4 (depending on how you set t...
Page 22 - Programming the DSS; Using the Remote: The Point & Select Rule
20 Some Indoor Stuff Programming the DSS ® Remote to Control Your TV In a few pages, you’ll use the DSS ® receiver’s menu system to find the dish pointing coordinates for your location. You’ll probablyfind it easier if you use the DSS ® remote instead of the receiver’s front panel buttons, so you ne...
Page 23 - TV Code List (for programming the DSS
21 Some Indoor Stuff A-Mark ...................................... 102 Admiral ..................................... 005 Amtron ...................................... 064 Akai .................................. 002, 103 Anam ................................ 104, 105 Anam National .................. ...
Page 24 - Setup
22 Some Indoor Stuff Using the Setup Menu to Find theElevation and Azimuth The DSS ® receiver is preprogrammed to give you the coordinates for pointing your dish at the satellite. All you have to do is enteryour zip code. First, plug in your DSS ® receiver. Setup The first time that you turn on the ...
Page 25 - Set the Elevation on the Dish; Locate the dish and support arm.
23 Some Indoor Stuff Set the Elevation on the Dish The first part of the dish pointing process is to set the dish topoint up toward the satellite. This is called “setting theelevation.” 1. Locate the dish and support arm. 2. Loosen the two elevation nuts so the support sleeve canrotate easily. 3. Ro...
Page 27 - A compass is required for this section.
25 Some Outdoor Stuff You’re finally ready to install the dish, right? Sorry, notjust yet. First you have to select the best mounting site.You may already know where you want to mount thedish, but it’s a good idea to examine all the options.Here’s an overview: First you’ll make a precise site survey...
Page 28 - Precise Site Survey; Using a Compass to Find the Satellite; Repeat this survey in several places on your property.
26 Some Outdoor Stuff Precise Site Survey In Chapter 1, you conducted a general site survey to find thelocation or locations that will provide the dish with a clear line ofsite to the satellite. Now you’ll use a compass to make a moreprecise survey. Using a Compass to Find the Satellite 1. Go outsid...
Page 29 - Do You Have A Suitable Location?
27 Some Outdoor Stuff Another Site Survey? You’ve gone through the site survey once already, butexperience tells us this second survey is crucial. Do You Have A Suitable Location? Based on the site surveys you made in the previous section, doyou have a clear view to the satellite from at least one l...
Page 30 - Choosing A Mounting Surface; Wall Studs or Solid Wood; This is the simplest mounting; Lap Siding; (You may need to install spacers underneath the; Brick or Poured Concrete
28 Some Outdoor Stuff Choosing A Mounting Surface Once you have identified the site (or sites) for mounting thedish, you need to choose a mounting method. The method formounting the dish depends on where you want to mount thedish and the type of mounting surface. You can install the dishon several s...
Page 31 - Other Mounting Options; Pole Mount; Do not use a pole mount in wet or marshy areas.; Chimney Mount; Use the roof mount only as a last resort
29 Some Outdoor Stuff Other Mounting Options • Pole Mount A pole mount is good if you want or need to install the dishsome distance away from your house. You may needsupporting guy wires if the pole extends too far above theground. Do not use a pole mount in wet or marshy areas. • Chimney Mount You ...
Page 32 - About Grounding the System; Grounding the DSS; How Many Cables and Wires Do I Need?
30 Some Outdoor Stuff About Grounding the System Now that you’ve selected your permanent mounting site (ornarrowed it down), you need to determine where you’ll run theRG-6 coaxial cables and how you’ll the ground the DSS ® system. Grounding the DSS ® system to the central building ground helps prote...
Page 33 - Estimating Cable Requirements; Acceptable central building ground points may include:
31 Some Outdoor Stuff Estimating Cable Requirements Here’s how to determine where to put the grounding blockand estimate the length of the RG-6 coaxial cables andground wires. 1. Locate the central building ground. You will ground thedish and the cable grounding block to a single point inthe central...
Page 35 - Testing the System; Earn Extra Credit; Temporary stand for the DSS; Tools Needed for the Test; phillips-head screwdriver
33 Testing the System Testing the System ➣ Some Indoor Stuff ➣ ➣➣ ➣ First Things First Some OutdoorStuff Testing the System Mounting The Mast Final Approach Earn Extra Credit This chapter includes instructions for setting up the dishon a temporary site in order to test the system. Whilethis is not s...
Page 36 - Setting Up the Temporary Stand; You must test the system outside; Assembling the Test Components
34 Testing the System Setting Up the Temporary Stand 1. Choose a location for the system test. Here are someconsiderations: • You must test the system outside • you’ll need a flat surface for the temporary stand • the site you pick for the test must have an unobstructed viewto the satellite • the si...
Page 37 - Tighten the bolts on the foot so that the mast will not rotate.
35 Testing the System mast 5 3. Tighten the bolts on the foot so that the mast will not rotate. 4. Secure the mounting foot to the temporary stand. Try usingclamps, lag bolts, or a helper to hold the mast foot in place. 5. Place the dish assembly on the mast. 6. Make sure you have a length of RG-6 c...
Page 38 - Connect the end of the cable to the LNB.; Hint
36 Testing the System BOLT NUT ( insert first ) OUT TOTV IN FROM ANT S-VIDEO VIDEO R L AUDIO WIDE BAND DATA SATELLITE IN PHONE JACK CH4CH3 LNB 8. Connect the end of the cable to the LNB. 9. Insert the end of the LNB into the end of the LNB supportarm. Push any extra cable back through the LNB suppor...
Page 39 - Picking Up the Satellite Signal; Point the Dish
37 Testing the System Picking Up the Satellite Signal In this section, you’ll pick up the satellite signal by pointing thedish toward the satellite. You’ve already set the elevation on thedish, so now you’ll need to point the dish to the correct azimuth.Keep in mind that for the system test, you’re ...
Page 40 - Bring Up the On-screen Signal Strength
38 Testing the System 4. Locate the tick mark on the compass that corresponds to theazimuth number you wrote down in the last chapter. 5. Point the LNB support arm in the same direction as theazimuth tick mark on the compass. 6. Lightly tighten the nuts on the LNB support sleeve so the LNBdoes not s...
Page 41 - adjust the Azimuth; Carefully rotate the dish one tick mark to the right.
39 Testing the System adjust the Azimuth 1. If necessary, loosen the nuts on the support sleeve so that theLNB support arm can rotate left and right. 2. Locate the piece of tape at the top of the mast. This tape ismarked with evenly spaced “tick” marks. 3. Carefully rotate the dish one tick mark to ...
Page 42 - If necessary, adjust the Elevation; Did you hear one continuous tone?; Go to the next step, Troubleshooting the System Test,; Your system is working and you have located the precise
40 Testing the System If necessary, adjust the Elevation If you still haven’t picked up the satellite signal, you may need toadjust the elevation. 1. Return the LNB support arm to the original compassdirection. 2. Tighten one of the three nuts on the support sleeve so thedish will not rotate left an...
Page 44 - Disconnecting Test Components; Do not skip this step!; Now that you know your components
42 Testing the System Disconnecting Test Components Do not skip this step! Now that you know your components are working, and you have a clear idea of how to connect thesystem, you’ll need to follow a different procedure to make apermanent connection. You don’t need to disconnect all the components,...
Page 45 - Mounting the Mast; Materials Needed
43 Mounting the Mast In Chapter 3, you conducted a precise survey andperformed other steps to help you decide on thepermanent mounting site for your DSS ® dish. In this chapter, you’ll actually begin the installation bymounting the dish mast on the surface you’ve chosenfor your permanent site. Which...
Page 46 - bubble level; Important Considerations:; Make sure the wooden surface is structurally sound
44 Mounting the Mast Mounting On Wall Studs orSolid Wood Materials Needed to Mount the Mast on Wall Studsor Solid Wood: (2) 5/16" x 3" lag screws (4) 5/16" x 2" lag screws (4) 5/16" washers Tools Needed to Mount the Mast on Wall Studsor Solid Wood: electric drill with 1/8" an...
Page 47 - Mounting on Wall Studs or; Do not mount the dish near
45 Mounting the Mast Step-by-step Instructions for Mounting on Wall Studs or Solid Wood 1. Locate the center of a stud where you want to mount themast foot. Make sure you locate and secure the mounting foot tothe center of a wall stud. Do not mount the dish near the edge of a stud. 2. Hold the mount...
Page 48 - Turn to Final Approach on page 63 for instructions on; IMPORTANT; Do not mount the DSS
46 Mounting the Mast 5. Remove the mounting foot and drill two 1/8" holes inthe two center hole locations and four 3/16" holes in thefour outside corner locations. 6. Use a 7/16" wrench to loosen the nuts on the mountingfoot so that you can rotate the mast to access both of thecenter mou...
Page 49 - Mounting on Lap Siding; Materials Needed to Mount the Mast on Lap Siding; Do NOT mount the DSS
47 Mounting the Mast Mounting on Lap Siding Materials Needed to Mount the Mast on Lap Siding (2) 5/16" x 3" lag screws (4) 5/16" x 2" lag screws (4) 5/16" washers Tools Needed to Mount the Mast on Lap Siding: electric drill with 1/8" and 3/16" wood bits bubble level 1/2...
Page 50 - on Lap Siding; Do not mount the dish near the; To locate a stud underneath panel siding, locate the
48 Mounting the Mast Step-by-step Instructions for Mounting on Lap Siding 1. Locate the center of a stud where you want to mount themast foot. If possible, choose a position where the mounting foot fits onone siding board. When the mounting foot spans two piecesof siding, it should positioned so tha...
Page 51 - Use a level to verify that the center line is perfectly vertical.; Skip to the section titled “Installing a Spacer” on
49 Mounting the Mast Mounting the Mast level on centerline of template Level Not Level No Yes 3. Use a level to verify that the center line is perfectly vertical. 4. Use a pencil to mark the two center holes and the fouroutside corner holes of the mounting foot. 5. Remove the foot and drill two 1/8&...
Page 52 - Installing a Spacer; Insert the spacer under the mounting foot.
50 Mounting the Mast Installing a Spacer When the mounting foot spans two pieces of siding, it should bepositioned so most of the foot is on the top board. A spacershould be installed to help hold the bottom of mounting foot inplace. The spacer can be made of either solid wood or plastic. 1. Measure...
Page 53 - Mounting on Brick or Poured Concrete
51 Mounting the Mast Mounting on Brick or Poured Concrete Materials Needed to Mount the Mast on Brickor Poured Concrete: (4) B4015 or equivalent double-expansion anchors (4) #20, 1/4" x 3" machine screws (4) 5/16" flat washers Tools Needed to Mount the Mast on Brickor Poured Concrete: el...
Page 54 - on Brick or Poured Concrete; Hold the mounting foot in position on the mounting surface.
52 Mounting the Mast Step-by-step Instructions for Mounting on Brick or Poured Concrete 1. Hold the mounting foot in position on the mounting surface. 2. If you are mounting on a vertical or sloped surface, use alevel to ensure that the center line is vertical. 3. Mark the four outside holes on the ...
Page 55 - Mounting On a Hollow or Cinder
53 Mounting the Mast Mounting On a Hollow or Cinder Block Wall Materials Needed to Mount the Mast on a Hollow orCinder Block Wall: (4) 1/4" hollow wall togglers (4) #20, 1/4" x 3" machine screws (4) 4/16" flat washers Tools Needed to Mount the Mast on a Hollow orCinder Block Wall: el...
Page 56 - on a Hollow or Cinder Block Wall; Center the mounting foot on the mark you made.
54 Mounting the Mast Step-by-step Instructions for Mounting on a Hollow or Cinder Block Wall 1. When installing togglers in cinder blocks, it is important toposition them in the core of the block. To position the footon the wall, measure 7-1/2" from one edge of the block andmark the center of th...
Page 57 - b. Pull the ring so the metal channel rests flush behind the wall.
55 Mounting the Mast b. Pull the ring so the metal channel rests flush behind the wall. Hold the ring tight and slide the plastic cap along the strapsuntil the cap is flush with the wall. c. Push the straps side-to-side to snap them off flush with thewall. d. Repeat for all four holes. 7. Use a 7/16...
Page 58 - Mounting the Dish On A Pole; Materials Needed to Mount the Dish on a Pole:
56 Mounting the Mast Mounting the Dish On A Pole Materials Needed to Mount the Dish on a Pole: (1) 1-1/4" inner diameter Schedule 40 galvanized steel pipe witha measured outer diameter of 1.6" (3) bags quick-setting concrete Tools Needed to Mount the Dish on a Pole: bubble level screwdriver ...
Page 59 - the Dish on a Pole; Use a hacksaw to cut a 45
57 Mounting the Mast Step-by-step Instructions for Mounting the Dish on a Pole 1. Dig a hole 36" deep and 8" to 12" wide at the mountinglocation. The depth of the hole must extend at least 6" below thefrost line. For most installations, a pole 6' long is sufficient,since this allows ...
Page 60 - Mounting the Mast on a Chimney; Materials Needed to Mount the Mast on a Chimney:
58 Mounting the Mast Mounting the Mast on a Chimney Materials Needed to Mount the Mast on a Chimney: (1) RCA D915 Chimney Mount Kit Tools Needed to Mount the Mast on a Chimney: bubble level 7/16" wrench screwdriver tin snips pliers ladder pencil Important Considerations: • Make sure the chimney ...
Page 61 - Mounting the Mast on a Roof; Materials Needed to Mount the Mast on a Roof:
59 Mounting the Mast Mounting the Mast on a Roof Materials Needed to Mount the Mast on a Roof: (2) 5/16" x 3" lag screws (4) 5/16" x 2" lag screws (4) 5/16" washers roof sealant Tools Needed to Mount the Mast on a Roof: electric drill with 1/8" and 3/16" wood bits bubble ...
Page 62 - the Mast on a Roof; Use a pencil to mark the six holes in the mounting foot.
60 Mounting the Mast Step-by-step Instructions for Mounting the Mast on a Roof 1. Locate the center of a rafter where you want the mountingfoot to be located. 2. Hold the mounting foot in a position so the center line iscentered on a rafter. 3. Use a bubble level to make sure the center line is perf...
Page 63 - Fill all six holes with a small amount of roof sealant.
61 Mounting the Mast 7. Fill all six holes with a small amount of roof sealant. 8. Use a 7/16" wrench to loosen the nuts on the mounting footso you can rotate the mast to access both of the centermounting holes. 9. Hold the mounting foot over the holes so the top part of themast will rotate and ...
Page 65 - Final Approach
63 Final Approach ➣ Some Indoor Stuff ➣ ➣➣ ➣ First Things First Some OutdoorStuff Testing the System Mounting The Mast Final Approach CAUTION Use caution when installing, adjustingor dismantling the dish and mast. Theweight of the dish may cause the dishand mast to swing down and strikeyou, a bystan...
Page 66 - Leveling the Mast; . If the mast is not level, the elevation and azimuth
64 Final Approach Leveling the Mast Leveling the mast is one of the most important steps ininstallation . If the mast is not level, the elevation and azimuth settings will not be accurate. This will make it difficult to obtainthe satellite signal. The mast must be level in both the side-to-side and ...
Page 67 - Is the bubble centered in the level’s window?; a) If the bubble is not centered, determine which side of the
65 Final Approach 4. Is the bubble centered in the level’s window? YES Continue to “Leveling Front-to-Back”. NO a) If the bubble is not centered, determine which side of the mounting foot needs to be raised. b) Unscrew the lag or machine screws from that side of the mounting foot. c) Place 5/16"...
Page 68 - Final Dish Assembly; Place the dish-LNB arm assembly on top of the mast.
66 Final Approach Final Dish Assembly 1. Place the dish-LNB arm assembly on top of the mast. 2. Find the length of RG-6 coaxial cable that will extend fromthe satellite dish to the cable’s point of entry into the house. If the distance of the RG-6 coaxial cable is greater than 112feet you may need t...
Page 69 - The hex retainer nut must be inserted into the top of; The National Electrical Code specifies that coaxial
67 Final Approach 5. Insert the end of the LNB into the end of the LNB supportarm (push any extra coaxial cable back through the supportarm). 6. Find the special hex retainer nut and insert it into the LNBmounting hole on top of the LNB support arm. Hint: The hex retainer nut must be inserted into t...
Page 70 - Locate a grounding block.
68 Final Approach Routing Cable and Grounding atthe House Entry Point 1. Locate a grounding block. 2. Attach the grounding block to the side of your house close tothe point you have chosen as the coaxial cable entry point.You may have to use anchors, togglers, or wood screwsdepending on the surface ...
Page 71 - Ensure that the routing of both grounding wires are secure.
69 Final Approach 7. Locate the grounding wire that will extend from thegrounding block to the central building ground. Attach thegrounding wire to the grounding block by placing it throughthe wire hole in the grounding block and tightening thescrew. 8. Route the grounding wire from the grounding bl...
Page 72 - Make sure there are no wires or pipes behind the; About the Phone Connection; The DSS
70 Final Approach Running Cable into the House andConnecting to the Receiver 1. Drill a 1/2" hole in the location you want the coaxial cable toenter your house. CAUTION Make sure there are no wires or pipes behind the wall in the area of the hole. 2. Locate the RG-6 coaxial cable that will exten...
Page 73 - Turn on your TV and the DSS
71 Final Approach Acquiring and Fine Tuning theSatellite Signal The signal strength meter is used to determine whether you arereceiving the satellite signal. It also indicates the strength of thesatellite signal. (Refer to your User’s Manual for information onusing the on-screen menus and other feat...
Page 75 - Restart the signal meter.; Ordering DSS; You have successfully completed the installation of your DSS; Programming with DIRECTV:
73 Final Approach 5. AFTER YOU GET A SIGNAL, continue adjusting the azimuth(compass direction) by rotating the dish in small incrementsleft and right until you achieve the highest possible signalstrength. 6. Tighten the support sleeve nuts so the dish will not rotateleft and right. 7. Slightly loose...
Page 76 - Appendix A: Troubleshooting; DSS
74 Appendix A: Troubleshooting Every Instruction Manual Needs aTroubleshooting Section... ...And this is it. Most times, problems experienced with the DSS ® system can be corrected quickly and simply. DSS ® Receiver Won’ t Turn On 1. Make sure the problem is not with the receiver — turn on thereceiv...
Page 77 - Troubleshooting; Remote Problems
75 Troubleshooting Remote Problems 1. Verify that your DSS ® receiver is receiving power. 2. Verify that your TV is set to the correct channel to receive theDSS ® signal: the S-video channel, the video input channel, or channel 3 or 4 (depending on how you set the CH3/CH4switch on the back of the re...
Page 78 - Can’ t Pick Up the Satellite Signal; NOT
76 ON/OFF DISPLAY ANTENNA MENU SELECT Troubleshooting Can’ t Pick Up the Satellite Signal Most problems with signal acquisition can be traced to one ofthese points: 1. Make sure you’re using RG-6 coaxial cable to connect the LNBto the grounding block and the grounding block to the DSS ® receiver. St...
Page 80 - Temporary Satellite Signal Loss; Rain fade is a normal, temporary loss of a; Overheated Components.; You hear a dialing sound while talking; Your DSS
78 Temporary Satellite Signal Loss If you lose the satellite signal temporarily, the problem canusually be traced to one of these points: 1. Rain Fade. Rain fade is a normal, temporary loss of a satellite signal due to the inability of the satellite signal topenetrate unusually heavy clouds, rainfal...
Page 81 - Appendix B: Connecting to a Phone Jack; Why Do You Need a Phone Jack?; To connect the DSS
79 Appendix B: Connecting to a Phone Jack Why Do You Need a Phone Jack? The DSS ® receiver calls a 1-800, toll-free telephone number once a month to update your access card. In addition, to easily orderpay-per-view events, you should have the DSS ® receiver connected to a phone line. These calls onl...
Page 82 - Connecting to a Phone Jack
80 Using a DSS ® Wireless Phone Jack System Since a phone jack may not be located near your DSS ® receiver, the DSS ® Wireless Phone Jack system allows you to easily put a phone jack right where you want it. The system consists of abase unit hooked to an existing phone jack and an extension unitthat...
Page 83 - Appendix C: Warranty Information; Digital Satellite System (DSS; What your warranty covers:
81 Appendix C: Warranty Information Digital Satellite System (DSS ® ) Limited Warranty What your warranty covers: • Any defect in materials or workmanship. • Basic installation, provided installation is performed by a Thomson ConsumerElectronics Authorized Installer. For how long after your purchase...
Page 84 - Warranty Information; If you are not located near an exchange point:
82 Warranty Information 3. Take your unit and your evidence of purchase date, such as a bill of sale, to theexchange location and you will be provided the new or refurbished unit. Pleaseretain all accessories such as the remote control hand unit. 4. If the repairs are covered by your warranty, you w...
Page 85 - What your warranty does not cover:; Acts of God, such as but not limited to lightning damage.; Product Registration:
83 Warranty Information What your warranty does not cover: • Acts of God, such as but not limited to lightning damage. • Adjustment of customer controls. • Damage from misuse or neglect. • A unit that has been modified or incorporated into other products or is used forinstitutional or other commerci...
Page 86 - Index
84 Index A access card 41, 73acquiring the satellite signal 37, 71aiming the dish using the on-screen signal meter 38 assembling the dish final assembly 66 audio/video jacks 10azimuth setting 39 B brick surface mounting option considerations 28, 51materials and tools needed 51 C cable, RG-6 coaxial....
Page 88 - CREATING A GREENER FUTURE; At; Thomson Consumer Electronics; we are dedicated to the preservation; Thomson; The Earth
86 100% RECYCLED PAPER MINIMUM 50% POST CONSUMER CREATING A GREENER FUTURE At Thomson Consumer Electronics we are dedicated to the preservation of our natural heritage and to a healthy and safe way of life for currentand future generations. This is a global effort which encompasses everyTHOMSON faci...