RCA PRO-SW220P - Manual
RCA PRO-SW220P – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.
Table of Contents:
- Page 2 – To reduce the risk of fire or; CAUTION; TO REDUCE THE RISK OF
- Page 5 – From Left or Right Speaker
- Page 8 – Printed in USA; Limited One-Year Warranty; We Service What We Sell
PRO-SW220P 200-Watt-Powered Subwoofer
Your RCA PRO-SW220P 200-Watt
Powered Subwoofer is designed to give
you the best possible low frequency sound
for the ultimate home theater experience.
You will be astonished by the realism it
adds to movie sound effects and the power
it lends to all kinds of music.
The subwoofer combines the power of a
built-in 200-watt RMS amplifier with a
responsive, 12-inch coated paper cone
woofer — all housed in a ported bass-
reflex enclosure to produce tight, floor-
rumbling powerful bass (down to 36 Hz)
that you can feel as well as hear. The
power indicator lets you know when the
subwoofer is operating.
Your subwoofer has an adjustable high cut
filter and high and low level inputs so it is
easily incorporated into existing systems,
or used as an integral part of a subwoofer/
satellite combination.
Its other features include:
Auto On/Off
— automatically switches
the PRO-SW220P’s amplifier to standby if
the subwoofer does not receive a signal for
about 11 minutes.
Standby Indicator
— power indicator
changes color when the subwoofer is
connected to power but not receiving a
signal.
High-Level Input
— lets you connect the
subwoofer to an amplifier’s or receiver’s
speaker outputs.
Note:
You need speaker wire (not
supplied) to connect the subwoofer to an
amplifier or receiver’s speaker outputs.
High Level Output
— lets you connect
the subwoofer between an amplifier or
receiver (without line out terminals) and
other speakers.
Low Level Input
— lets you connect the
subwoofer to an amplifier’s or receiver’s
subwoofer out or pre out jacks. These
inputs automatically sum left and right
channel information.
Note
: You need phono cables (not
supplied) to connect the subwoofer to an
amplifier or receiver’s subwoofer out or
pre out jacks.
Volume Control
— lets you match the
PRO-SW220P’s output level to your
satellite speakers’ output (if used).
Phase (Polarity) Switch
— Inverts the
subwoofer’s output polarity so you can set
it to match the main speakers.
Frequency Hz Control
— lets you set the
high frequency cutoff point. Rotated fully
clockwise, the subwoofer cuts high
frequencies over 200 Hz. Rotated fully
counterclockwise, it cuts high frequencies
over 50 Hz.
©
2001 RadioShack Corporation.
All Rights Reserved.
"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.
Summary
2 S S S SA A A AF FF FE E E ET T T TY Y Y Y IIIIN N N NS S S ST T T TR R R RU U U UC C C CT T T TIIIIO O O ON N N NS S S S • Never open the cabinet or remove the metal control panel, as this might result in electrical shock or damage to the unit. • If your PRO-SW220P needs servicing, contact your lo...
5 You need two pairs of speaker pins (available at your local RadioShack store) to make the connection. Follow these steps to connect the wires to each terminal using speaker pins. 1. Separate the conductors for a length of about 2 inches on the end of each wire. Then strip 1 / 2 inch of insulation ...
RadioShack A Division of RadioShack Corporation Fort Worth, Texas 76102 40-5031 03/2001 Printed in USA Limited One-Year Warranty This product is warranted by RadioShack against manufacturing defects in material and workman-ship under normal use for one (1) year from the date of purchase from RadioSh...
