RCA D770 - Manual - manualsarea.com

Page 2 - : For users of RCA and PROSCAN DBS products: Older DBS models require; INFO; or; MENU; key on this remote be used to make program; Table of Contents; Note; : Reprogramming may be required after batteries are replaced.; Battery Installation

Thank you for purchasing this RCA universal remote control. Thisproduct is designed to operate a wide variety of video and audiocomponents. Please retain this guide for future reference. This universal remote control is already programmed for most RCA, GE, and PROSCAN branded TVs, VCRs, DBS systems ...

Page 3 - Key Description; SAT; OK

Key Description ANTENNA In TV Mode, lets you switch the source of the video signalfrom satellite signals to an off-airantenna or cable signal when using the OUT TO TV jack. In VCR Mode, it functionsas a TV/VCR input key. ARROWS Use the navigation arrows to move the on-screen highlight up,down, left,...

Page 4 - appears on the screen. Pressing; will display more

5 LED indicator light This light turns red at each valid key press. When programming the remote control, it flashes or turns on or off to indicateprogramming status. MENU Displays the Main menu. If you are already in the menu system, press OK or MENU to select a highlighted choice. When you are usin...

Page 5 - Programming For TV— Direct Entry Method; Programming For VCR— Direct Entry Method

Programming For TV— Direct Entry Method 1. Manually turn on the TV. 2. Locate the enclosed TV Code List. Find your brand of TV. 3. Press and hold the TV key. 4. Enter a code from the code list. 5. Release the TV key, and then press ON•OFF to see if the TV responds to the remote control commands. If ...

Page 6 - Programming The AUX1 And AUX2 Keys; ON•OFF

7 Programming The AUX1 And AUX2 Keys You can assign any one of the following components to the AUX1 or AUX2 keys: A second TV, VCR, DVD, satellite system, cable box, or an audio component. Note: The AUX1 key is pre-programmed with codes to control Dish Network digital satellite receivers. The SAT ke...

Page 7 - Using Automatic Code Search; does; Using The Remote To Control A Component

8 Using Automatic Code Search The following instructions can be used to program the remote to controlthe TV, VCR or DVD. If you want to exit the automatic code searchwithout programming any of your components, press the CLEAR key until the LED (red light) turns off. 1. Turn on the component you want...

Page 8 - ENTERING THE MENU MODE; GUIDE; EXITING THE MENU MODE

9 Changing The RF Remote Control Code (Continued) 1. Select Options in the Main menu. 2. Select System Options. 3. Select RF Remote. 4. If you normally use the SAT key on your remote to control your RCA satellite receiver, choose a number between 000 and 255. Follow theon-screen instructions to ente...

Page 9 - Troubleshooting

10 Troubleshooting Problem: The remote can’t be programmed to operate yourcomponent. • You may be too far away from the component or at a wrong angle. Thisremote uses IR (infrared) technologyto communicate with components.The remote sends the code and thecomponent’s IR sensor reads thecode. Therefor...

Page 10 - Questions; RECORD

11 Questions Please visit www.rca.com Problem: The VCR won’t record. • As a safety feature, you must press the RECORD key twice to begin recording. • Make sure the tape is properly loaded in the VCR. • Make sure the tape is not write-protected. If the safety tab is removed, the tape is write-protect...

Page 11 - Consolidate Five Remote Controls Into One!

* Your RCA universal remote control is compatible with most brands of infrared remote-controlled components manufactured after 1990. Some well-known brands are shown below. The complete list of brands is found on the Code List inside this package. The remote already operates most RCA, GE and PROSCAN...

RCA D770 - Manual

Table of Contents:

Summary

Other RCA Models