RCA ANT3036W - Manual
RCA ANT3036W – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.
Table of Contents:
- Page 2 – Step 3: Unfold the back section; so that the stamps face you.; Step 4: Connect the back section to the
- Page 3 – Step 5: Unfold the front section; On the front section, find the reflector booms
- Page 4 – booms so that the stamps face you.; Step 7: Attach the phasing lines; Find the washers and 10/32” hex nuts in the
- Page 5 – Step 9: Install the transformer; Find the 10/32” hex nuts and washers in your; Step 10: Insert end caps; gently tap them into the antenna booms to; Step 8: Attach the mast clamp insert; Insert the U-bolt into the mast clamp on
- Page 6 – Step 12: Connect the coax cable; it or use of plastic wire ties.; Step 11: Attach the antenna to the mast; Point small end of antenna toward your local; 2 Month Limited Warranty
- Page 7 – Paso 2: Desdoble la sección central; Voltee la sección central y desdoble los elementos; Lea la hoja de INFORMACIÓN IMPORTANTE DE SEGURIDAD
- Page 8 – Paso 3: Desdoble la sección posterior; orientadas hacia usted.; Paso 4: Conecte la sección posterior a la
- Page 9 – Paso 5: Desdoble la sección frontal
- Page 10 – Paso 7: Fije las líneas de fase
- Page 11 – Paso 9: Instale el transformador; Estos elementos tienen postes en sus bases.; Paso 10: Inserte las tapas de los extremos; Utilice un martillo de goma para golpearlos; Paso 8: Fije el inserto de la; orientados hacia el lado cerrado del perno en U.
ANT3036W / ANT3036X
Outdoor Antenna
User’s Guide
Step 1: Unpack
Remove all three sections of the antenna and the hardware bag from
package. Make sure the following parts are in the package:
• 3 antenna sections
• Hardware bag
U-Bolt
Transformer
Mast Clamp Insert
(4) Plugs
(4) 10/32” Hex nuts
(2) 1/4” Hex Nuts
Matching
(8) 7/16” Washers
• 58” mast (ANT3036W only)
Middle
section
Step 2: Unfold the middle section
Find the middle section of the antenna
(illustrated on the left).
Starting from the rear of the middle section,
unfold the long VHF Elements until they lock
into place (as illustrated below).
Turn the middle section over and unfold the
shorter elements on the other side.
Rear
BEFORE YOU START!!!
Please read the IMPORTANT SAFETY INFORMATION sheet
included in this package.
Back
Middle
Front
"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.
Summary
Step 3: Unfold the back section On the middle section (the one you unfolded in step 2), find the word “Back” stamped in blue on the boom. Find the same stamp on the boom of the back section. Line up both booms so that the stamps face you. Remove the screw and nut from end of the middle section close...
Step 5: Unfold the front section Find the front section of the antenna (illustrated on the left). On the front section, find the reflector booms (illustrated below). Each reflector boom has four elements. Unfold each slightly. Then, starting with the element closest to the main boom, unfold the elem...
On the front section (the one you unfolded in step 5), find the word “Front” stamped in red on the boom. Find the same stamp on the boom of the middle section. Line up both booms so that the stamps face you. Remove the screw and nut from end of the middle section closest to the front section. Insert...
