Page 2 - Equipment Approval Information; Interference Information; Important Information
2 Equipment Approval Information Your telephone equipment is approved for connection to the Public Switched Telephone Network and is in compliance with parts 15 and 68, FCC Rules and Regulations and the TechnicalRequirements for Telephone Terminal Equipment published by ACTA. 1 Notification to the L...
Page 3 - Table of Contents
3 S E E M A R K I N G O N B O T T O M / B A C K O F P R O D U C T RISK OF ELECTRIC SHOCK DO NOT OPEN WARNING: TO PREVENT FIRE ORELECTRICAL SHOCKHAZARD, DO NOTEXPOSE THISPRODUCT TO RAINOR MOISTURE. THE LIGHTNINGFLASH AND ARROWHEAD WITHIN THETRIANGLE IS AWARNING SIGNALERTING YOU OF“DANGEROUSVOLTAGE” I...
Page 4 - CID R
Table of Contents F LASH ................................................................................................................. 26 R EDIAL ................................................................................................................ 26 R EVIEWING THE R EDIAL N UMBERS .....
Page 5 - Introduction
5 Introduction CAUTION: When using telephone equipment, there are basic safety instructions that should always be followed. Refer to the IMPORTANT SAFETYINSTRUCTIONS provided with this product and save them for future reference. Your Four-Line Speakerphone is a full-featured phone ideally suited for...
Page 6 - Make sure your package includes the following items:
6 Connections & Setup Telephone Jack Requirements To use this phone, you will need an RJ11C (for a single line) or a RJ14C (for two lines) typemodular phone jack, which might look like the one pictured here, installed in your home. Ifyou don’t have either modular jack, call your local phone comp...
Page 7 - Base Layout
7 Connections & Setup DELETE EXIT SELECT/SAVE DIAL STORE MENU DIRECTORY NEW MESSAGE INTERCOM CONFER LINE 4 LINE 3 LINE 2 LINE 1 PRIVACY PAGE TRANSFER PAUSEREDIAL VOLUME FLASH HEADSET SPEAKER MUTE HOLD 16 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 INTERCOM/MEMORY LOG MEM. MEM. MEM. MEM. MEM. MEM. MEM. M...
Page 8 - Important Installation Information; Never install telephone wiring during a lightning storm.; Important Installation Guidelines; Avoid areas of excessive moisture or extremely low temperature.
8 Connections & Setup Important Installation Information • Never install telephone wiring during a lightning storm. • Never install telephone jacks in wet locations unless the jack is specifically designed for wet locations. • Never touch non-insulated telephone wires or terminals, unless the te...
Page 9 - Installing the Phone; placed on a level surface, such as a table top or desk.
9 Connections & Setup Installing the Phone The phone may be connected to two 2-line (RJ14C) wall jacks or four single line (RJ11C)wall jacks to accomodate all four lines. 1. Choose an area near an electrical outlet and telephone wall jack. Your phone should be placed on a level surface, such as ...
Page 13 - Other System Phones; OR; Programing the Telephone; This telephone has several programmable functions.; Language; Press the MENU button while in standby mode.
13 Connections & Setup Other System Phones 1. Press LINE 1. 2. Look at all the other stations. If they all indicate line 1 is being used, the connection is correct. OR 1. Press the INTERCOM button. The display shows INTERCOM and ENTER CALLING PHONE ID. 2. Enter a phone ID by pressing an Intercom...
Page 14 - Priority Line
14 Connections & Setup 3. Press the SELECT button. 4. Use the REVIEW < or > button to scroll to SET RING TONE. 5. Press the SELECT button. The ringer tone settings for each of the four telephone lines show in the display. 6. Use the REVIEW < or > button to scroll to through each ring...
Page 15 - Delay Ring; Use this setting to delay the Central Office ring.; Phone ID
15 Connections & Setup Delay Ring Use this setting to delay the Central Office ring. 1. Press the MENU button while in standby mode. 2. Use the REVIEW < or > button to scroll to SET PHONE OPTIONS . 3. Press the SELECT button. 4. Use the REVIEW < or > button to scroll to SET DELAY RIN...
Page 16 - Phone Name; Intercom Auto Answer
16 Connections & Setup NOTE: If the phone cannot find an ID, determine if there are too many phones connected to the system. A maximum of 16 phones can be connected in the system atone time. NOTE: To changing a phone ID, press the SELECT button. Select the new ID by pressing the corresponding me...
Page 17 - or; Flash Time; Call Alert Tone
17 Connections & Setup 3. Press the SELECT button. 4. Use the REVIEW < or > button to scroll to INTERCOM AUTO ANS . 5. Press the SELECT button. 6. Use the REVIEW < or > button to choose YES or NO . 7. Press the SELECT button to save. Flash Time 1. Press the MENU button while in stand...
Page 18 - Display Contrast
18 Connections & Setup 5. Press the SELECT button. 6. Use the REVIEW < or > button to scroll to ON or OFF . 7. Press the SELECT button to save. The cursor automatically moves to LINE 2. 8. Repeat steps 6 and 7 for each telephone line. After you select a tone for Line 4, press the EXIT butt...
Page 19 - • uses multiple area codes
19 Connections & Setup Local Area Code (Not applicable to model 25403.) 1. Press the MENU button while in standby mode. 2. Use the REVIEW < or > button to scroll to SET AREA CODE. 3. Press the SELECT button. 4. Use the REVIEW < or > button to scroll to LOCAL AREA CODE. 5. Press the S...
Page 20 - Manually Setting the Time and Date; Press the SELECT button, and the cursor moves to the minute field.
20 Connections & Setup 3. Press the SELECT button. 4. Use the REVIEW < or > button to scroll to REGIONAL AREA CODES. 5. Press the SELECT button. All six regional area code fields and Enter Number show in the display. 6. Use the touch tone pad on your phone to enter up to six regional area ...
Page 21 - Hour Format; Restoring the Default Settings
21 Connections & Setup 12. Use the REVIEW < or > button to select the date. 13. Press the SELECT button, and the cursor moves back to the hour field. 14. Press the EXIT button. NOTE: You may press EXIT at any step in the process. It is not necessary to re-program the complete time & da...
Page 22 - Operation; Basic Operation; Making Calls with the Handset
22 Operation Basic Operation Your phone provides the convenience of accessing four separate telephone lines, each obtained from the telephone company and eachhaving its own phone number. This is generally applicable to small offices. It provides for 16 telephones (or stations) to share multiple line...
Page 23 - Making Calls with the Optional Headset; If you receive a call on the priority line,
23 Operation Making Calls with the Optional Headset 1. Connect the headset plug to the HEADSET jack on the side of the base. 2. Adjust the headset to rest comfortably on top of your head and over your ear. 3. Move the microphone to approximately 2 to 3 inches from your mouth. 4. Press the HEADSET bu...
Page 24 - If you receive a call on a line other than the priority line,; Pick up the handset and press the corresponding line button, OR; Switching Between the Speakerphone, Handset, and Headset
24 Operation 3. Press the HEADSET button (headset mode). 4. When finished, hang up the handset, press the SPEAKER button or press the HEADSET button. If you receive a call on a line other than the priority line, 1. Pick up the handset and press the corresponding line button, OR 2. Press the SPEAKER ...
Page 25 - Do Not Disturb; the duration by 1 hour intervals up to 24 hours.; Hold; Placing a Call on Hold
25 Operation Do Not Disturb 1. When the unit is idle, press the PRIVACY button. The Privacy indicator flashes and the last setting is displayed. 2. Use the REVIEW < or > button to the duration. You may choose from 15 minutes, 30 minutes, 45 minutes, 1 hour, or 2 hours and increase the duration...
Page 26 - Flash; Press the REDIAL button; Reviewing the Redial Numbers; Your phone records up to six previously dialed phone numbers.; Transferring a Call to Another Station; indicator flashes green.
26 Operation Flash Use the FLASH button to activate custom calling services such as call waiting or call forwarding, which are available through yourlocal phone company. Redial 1. Pick up the handset or press the SPEAKER button (speakerphone mode), and the priority line is automatically selected, OR...
Page 27 - line button and repeat the transfer process from step 1.; Receiving a Transferred Call from Another Station; Providing Privacy
27 Operation • If the party at the other station doesn’t pick up the transferred call, and you want to attempt to transfer to another station, press the line button and repeat the transfer process from step 1. Receiving a Transferred Call from Another Station If a call is transferred to your station...
Page 28 - Volume; Ringer Volume; Conference Calls; To connect and conference; Press the HOLD button to place the call on hold.
28 Operation Volume The ringer, speaker, and handset/headset volume is set independently with the VOLUME up and down buttons. There are 8 possible volumesettings per mode. The volume indicator scale is displayed during volume adjustment. Ringer Volume 1. While the phone is on the hook, press the VOL...
Page 29 - To disconnect one party:; Hang up the handset, or press the SPEAKER or HEADSET button.; Intercom Calls; Answering an Intercom Call
29 Operation To disconnect one party: Press the line button for the person you want to continue speaking with, and the other party is automatically disconnected. To disconnect both parties: Hang up the handset, or press the SPEAKER or HEADSET button. NOTE: If you press the HOLD button to put them on...
Page 30 - Intercom Hold; Make an intercom call or answer an intercom call.; Intercom Conference Calls; Place a call or make an intercom call.
30 Operation NOTE: If you are using the speakerphone, press the INTERCOM button to answer. If you are using the headset (headset indicator flashes), press the INTERCOMbutton., or when the intercom indicator turns green, lift the handset and begin speaking. NOTE: Press SPEAKER or lift the handset to ...
Page 31 - Caller ID; To disconnect both parties:; Hang up the handset, or press the SPEAKER button.; Paging All Stations; Summary Screen; Battery indicator; 0 Total CALLS; Name of phone
31 Caller ID To disconnect both parties: Hang up the handset, or press the SPEAKER button. NOTE: If you press the HOLD button to put them on hold first, you may then disconnect from each party individually. Paging All Stations 1. Lift the handset. 2. Press the PAGE button and listen for the beep. Th...
Page 32 - Receiving and Storing CID Records; • Press the REVIEW < o r > button to scroll through the call records.; Saving a CID Record to the Intercom/Memo Log or to Phone Book Memory; If you do not need to edit the name or number, press the STORE button.; JOHN SMITH
32 Caller ID Receiving and Storing CID Records This unit receives and displays information transmitted by your local phone company. This information can include the phone number, dateand time; or the name, phone number, date and time. The unit can store up to 99 calls for later review. When the memo...
Page 33 - Deleting a CID Record; This feature allows you to clear all CID records at once.; Dialing Back; If You Programmed Your Local Area Code
33 Caller ID Deleting a CID Record To delete the record shown in the display, press the DELETE button once. Deleting All Call Records This feature allows you to clear all CID records at once. 1. While viewing a CID record, press and hold the DELETE button. PRESS DELETE AGAIN CLEAR ALL CALLER ID show...
Page 34 - If You Did Not Program Your Local Area Code; Call Waiting Caller ID; Storing a Number and Name in Memory; ENTER NAME
34 Caller ID If You Did Not Program Your Local Area Code 1. Use the REVIEW < o r > button to display the number you want to dial. You will only see 10-digit numbers (i.e.234-555-1234). 2. Press DIAL to dial back. You may adjust the number format if “Press 65 to adjust ” shows in the display. C...
Page 35 - Memory; ENTER LOCATION
35 Memory 4. Use the touch-tone pad to enter a name (up to 21 characters). More than one letter is stored in each of the number keys. For example, to enter Bill Smith, press the 2 key twice for the letter B. Press the 4 key 3 times for the letter I. Press the 5 key 3 times for the letter L. Pressthe...
Page 36 - Reviewing the Memo Log (memory location memory); Press the EXIT button when you are finished reviewing memories.; Editing a Name or Number Stored in Phone Book (Directory) Memory; While viewing the desired number, press the SELECT button.
36 Memory Reviewing the Memo Log (memory location memory) 1. Press the DIRECTORY button. 2. Press the Intercom/MemoryLog button (1-16). 3. Press the EXIT button when you are finished reviewing memories. Editing a Name or Number Stored in Phone Book (Directory) Memory 1. Press the DIRECTORY button. 2...
Page 37 - Storing a Pause in Memory
37 Memory Storing a Pause in Memory Use the REDIAL/PAUSE button to insert a delay in the dialing sequence of a stored telephone number when a pause is needed (for example,when you must dial a 9 to get an outside line or when you must enter codes to access your bank’s information line). Dialing a Sto...
Page 38 - DELETE; Clear All Memories; SET SET PHONE OPTIONS.; Chain Dialing
38 Memory To delete an Intercom/Memo Log: 1. Press the DIRECTORY button. 2. Press the corresponding button (1-16) for the Intercom/Memo Log you want to delete. 3. Press the DELETE button and delete. DELETE again shows in the display. 4. Press the DELETE button again to confirm. NOTE: Press the EXIT ...
Page 39 - Other Information; For example; Display Messages; 0 TOTAL CALLS; UNKNOWN CALLER; BLOCKED CALL; Battery power level is low.
39 Other Information For example Memory location Local access number of long distance company 6 Authorization code (ID) 7 Long distance phone number 8 1. Press the line you want. 2. Press memory location 6. 3. Press memory location 7. 4. Press memory location 8. Display Messages The following specia...
Page 40 - Operation By Battery; Troubleshooting Guide
40 Other Information Operation By Battery If the power cord is not plugged into the unit, and the battery is available, the unit enters Battery Operation Mode. In this mode, the unitfully supports all operational features, except the intercom call function. Operation without Power If the power cord ...
Page 42 - General Product Care; DO NOT expose to direct sunlight or moisture.; Service
42 Other Information General Product Care To keep your telephone working and looking good, follow these guidelines: • Avoid putting the phone near heating appliances and devices that generate electrical noise (for example, motors or fluorescent lamps). • DO NOT expose to direct sunlight or moisture....
Page 43 - Limited Warranty
43 Other Information Limited Warranty What your warranty covers: • Defects in materials or workmanship. For how long after your purchase: • One year, from date of purchase. (The warranty period for rental units begins with the first rental or 45 days from date of shipment to the rental firm, whichev...
Page 45 - To Order; AC power adapter; Accessory Order Form
45 To Order To place your order by phone, haveyour Visa, MasterCard or DiscoverCard ready and call the toll-freenumber listed below. Use this number only to place anorder for accessory items listed onthis order form. 1-800-338-0376 To place your order by mail, detachand mail the completed order form...
Page 46 - Index
46 Index Dialing a Stored Number 37Dialing Back 33Display Contrast 18Display Messages 39Do Not Disturb 25 E Editing a Name or Number Stored in a Memo Log(Memory Location) 36 Editing a Name or Number Stored in Phone Book(Directory) Memory 36 Equipment Approval Information 2 F Flash 26Flash Time 17 G ...
Page 48 - Printed in China
Visit the RCA web site at www.rca.com Please do not send any products to the Indianapolis address listed in this manual or on the carton. This will only add delays inservice for your product. ATLINKS USA, Inc. 101 West 103rd Street Indianapolis, IN 46290 ©2003 ATLINKS USA, Inc. Trademark(s)® Registe...
Page 50 - Información sobre la Aprobación de Equipo; Información de Interferencias; Información Importante
2 Información sobre la Aprobación de Equipo El equipo de su teléfono esta aprobado para la conexión con la red Telefónica Pública (Public Switched Telephone Network) y cumple con los requisitos establecidos en las secciones 15 y 68 de las Reglas yRegulaciones de la FCC y con los Requerimientos Técni...
Page 51 - Tabla de Contenido
3 VEA ADVERTENCIA EN LA PARTE POSTERIOR/BASE DEL PRODUCTO. RIESGO DE SACUDIDA ELÉCTRICA NO ABRA ADVERTENCIA: PARA PREVENIREL RIESGO DEUNFUEGO O DE UNASACUDIDAELECTRICA, NOEXPONGAESTE APARATO A LALLUVIA O A LAHUMEDAD. EL RELÁMPAGO Y LAPUNTA DE FLECHADENTRO DEL TRIÁNGULOES UNA SEÑAL DEADVERTENCIA,ALER...
Page 53 - Introducción
5 Introducción CUIDADO: Cuando utilice equipo telefónico, hay instrucciones básicas de seguridad que siempre deben seguirse. Refiérase a la sección INSTRUCCIONES IMPORTANTES DESEGURIDAD provistas con este producto y guárdelas para referencia en el futuro. Su teléfono de Cuatro Líneas con Altavoz es ...
Page 54 - Conexión y Programación; Requerimientos de Enchufe Telefónico; Base; Lista de Partes
6 Conexión y Programación Requerimientos de Enchufe Telefónico Para utilizar este teléfono, usted necesitará un enchufe modular tipo RJ11C (para una línea sencilla) otipo RJ14C (para dos líneas), que puede ser como el enchufe ilustrado aquí, instalado en su casa. Siusted no tiene ningún enchufe modu...
Page 55 - Botón de la Línea 2; Formato de la Base
7 Conexión y Programación DELETE EXIT SELECT/SAVE DIAL STORE MENU DIRECTORY NEW MESSAGE INTERCOM CONFER LINE 4 LINE 3 LINE 2 LINE 1 PRIVACY PAGE TRANSFER PAUSEREDIAL VOLUME FLASH HEADSET SPEAKER MUTE HOLD 16 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 INTERCOM/MEMORY LOG MEM. MEM. MEM. MEM. MEM. MEM. MEM. M...
Page 56 - Informacion Importante para la Instalacion
8 Conexión y Programación Informacion Importante para la Instalacion • Nunca instale cableado telefónico durante una tormenta de relámpagos. • Nunca instale enchufes telefónicos en localizaciones mojadas a menos que el enchufe haya sido diseñado específicamente para localizaciones mojadas. • Nunca t...
Page 57 - Instalacion del Telefono
9 Conexión y Programación Instalacion del Telefono El teléfono puede estar conectado a dos enchufes telefónicos de 2 líneas (RJ14C) o 4 enchufes de líneasencillo (RJ11C) para acomodar las 4 líneas. 1. Escoja un área cerca de un enchufe eléctrico y de un enchufe telefónico de pared. Su teléfonodeberí...
Page 60 - Terminal de Datos
12 Conexión y Programación 5. Conecte el cable del auricular: Conecte un extremo del cable espiral en el enchufe al costado de la base y el otro extremo en el auricular, y coloque el auricular sobre la base. 6. Verifique qua haya tono de marcar: Levante el auricular y escuche para ver si hay tono de...
Page 61 - Otros Teléfonos en el Sistema; Para Programar el Teléfono; Idioma; Tono del Timbre
13 Conexión y Programación Otros Teléfonos en el Sistema 1. Oprima el botón de Línea 1. 2. Vea todas las otras estaciones. Si todas indican que la Línea 1 está en uso, la conexión está correcta. O 1. Oprima el botón de interfono (“INTERCOM”). La pantalla indica “INTERFON ” e “INSC IDENTIFIC DEL TELE...
Page 62 - Línea Prioritaria
14 Conexión y Programación 3. Oprima el botón “SELECT” para salvar. 4. Utilice los botones para revisar (“REVIEW < o > ”) para llegar a la indicación “PROG TONO TIMBRE.” 5. Oprima el botón “SELECT.” La programación del tono del timbre para cada una de las líneas telefónica aparecerá en la pant...
Page 63 - Para Retrasar el Timbre; Identificador del Teléfono
15 Conexión y Programación Para Retrasar el Timbre Utilice esta programación para retrasar el timbrado en la Oficina Central. 1. Oprima el botón de menú (“MENU”) mientras está en la modalidad de alerta. 2. Utilice los botones para revisar (“REVIEW < o >”) para llegar a la indicación “PROG OPCI...
Page 64 - Nombre Telefónico; Para Contestar Automáticamente el Interfono
16 Conexión y Programación NOTA: Si el teléfono no puede encontrar un identificador, determine si hay muchos teléfonos conectados al sistema. Un máximo de 16 teléfonos pueden estar conectados en el sistema almismo tiempo. NOTA: Para cambiar un identificador telefónico, oprima el botón “SELECT.” Sele...
Page 65 - Tiempo para Servicios Especiales
17 Conexión y Programación 3. Oprima el botón “SELECT” para salvar. 4. Utilice los botones para revisar (“REVIEW < o >”) para llegar a la indicación “AUTO CONTEST INTERF.” 5. Oprima el botón “SELECT.” 6. Utilice los botones para revisar (“REVIEW < o > ”) para seleccionar “SI ” o “NO.” 7....
Page 66 - No Desconocido o Bloqueado (No es aplicable al modelo 25403); Contraste de la Pantalla
18 Conexión y Programación 5. Oprima el botón “SELECT.” 6. Utilice los botones para revisar (“REVIEW < o >”) para seleccionar entre activado y desactivado (“ON ” or OFF ”). 7. Oprima el botón “SELECT” para salvar. El cursor se mueve automáticamente a la LINEA 2. 8. Repita los pasos 6 y 7 para ...
Page 67 - Clave de Área Local (No es aplicable al modelo 25403); Claves de Área Regionales (No es aplicable al modelo 25403)
19 Conexión y Programación Clave de Área Local (No es aplicable al modelo 25403) 1. Oprima el botón de menú (“MENU”) mientras está en la modalidad de alerta. 2. Utilice los botones para revisar (“REVIEW < o >”) para llegar a la indicación “PROG CLAVE DE AREA.” 3. Oprima el botón “SELECT” para ...
Page 68 - Para Programar Manualmente la Hora y la Fecha
20 Conexión y Programación 3. Oprima el botón “SELECT” para salvar. 4. Utilice los botones para revisar (“REVIEW < o > ”) para llegar a la indicación “CLAVE DE AREA REGIONAL.” 5. Oprima el botón “SELECT.” Los campos de las seis claves de área regionales y la indicación “Inscriba Número” aparec...
Page 69 - Formato de Hora
21 Conexión y Programación 12. Utilice los botones para revisar (“REVIEW < o >”) para seleccionar la fecha. 13. Oprima el botón “SELECT,” y el cursor regresa al campo de la hora. 14. Oprima el botón de salida (“EXIT”). NOTA: Usted puede oprimir el botón de salida (“EXIT”) en cualquier paso del...
Page 70 - Operación; Operación Básica; Para Hacer una Llamada con el Altavoz
22 Operación Operación Básica Su teléfono le ofrece la conveniencia de poder tener acceso a cuatro líneas telefónicas por separado, cada una habiendo sida obtenida a través de la compañíatelefónica y cada una teniendo su propio número telefónico. Esto generalmente es aplicable a pequeñas oficinas. L...
Page 71 - Para Hacer Llamadas con los Audífonos Opcionales; Marcado Previo; Si usted recibe una llamada en su línea prioritaria,
23 Operación Para Hacer Llamadas con los Audífonos Opcionales 1. Conecte los audífonos en el enchufe de audífonos marcado (“HEADSET”) al costado de la base. 2. Ajuste los audífonos a que descansen sobre su cabeza y sobre su oreja. 3. Mueva el micrófono a aproximadamente 2 a 3 pulgadas de su boca. 4....
Page 72 - Para Cambiar Entre Altavoz, Auricular y Audifonos
24 2. Oprima el botón de altavoz (“SPEAKER”) (en modalidad de altavoz), u Operación 3. Oprima el botón de audífonos (“HEADSET”) (en modalidad de audífonos). 4. Cuando haya terminado, cuelgue el auricular, oprima el botón de altavoz (“SPEAKER”) o el botón de audífonos (“HEADSET”). Si usted recibe una...
Page 73 - Favor de No Molestar; En Espera; Para Poner una Llamada en Espera; Para Liberar una Llamada
25 NOTA: También el cambio de altavoz a auricular o a audífonos cancela el enmudecedor. Operación Favor de No Molestar 1. Cuando el aparato está inactivo, oprima el botón de privacidad (“PRIVACY”). El Indicador de Privacidad parpadea y la última programación semuestra en la pantalla. 2. Utilice los ...
Page 74 - Botón “FLASH”; Para Volver a Marcar; Para Revisar los Números de “Redial”
26 NOTA: La llamada que está en espera puede ser levantada desde cualquier estación utilizando este procedimiento. Operación Botón “FLASH” Utilice el botón de servicios especiales (“FLASH”) para activar servicios especiales como llamada en espera o transferencia de llamada, que son disponibles atrav...
Page 75 - Para Recibir una Llamada Transferida desde otra Estación; Privacidad; Para Ofrecer Privacidad
27 indicador de línea parpadea en verde. Operación • Si la persona del otro lado de la estación no contesta y usted desea intentar transferir la llamada a otra estación, oprima el botón de la línea y repita el proceso de transferencia desde el paso 1. Para Recibir una Llamada Transferida desde otra ...
Page 76 - Volumen; Volumen del Timbre; Llamadas en Conferencia; Para conectar una llamada en conferencia:
28 NOTA: Si usted pone una llamada en espera mientras está en modalidad de privacidad, nadie más que usted puede tener acceso a la línea en espera. Operación Volumen El nivel de volumen del timbre, altavoz, y auricular/audífonos puede programarse independientemente con los botones para ajustar el vo...
Page 77 - Para Desconectar a una Persona:; Llamadas por Interfono; Para Contestar una Llamada de Interfono
29 NOTA: Si usted tiene más de una línea en espera, y usted quiere tener una llamada en conferencia, primero tiene que seleccionar una línea en la que usted quiera poner la conferencia. Operación Para Desconectar a una Persona: Oprima el botón de línea de la persona con la que usted quiera seguir co...
Page 78 - Llamada en Interfono en Espera; Llamadas en Conferencia por Interfono
30 Cuando usted recibe una llamada por el INTERFONO, el indicador del interfono (“INTERCOM”) parpadea en rojo, y la pantalla muestra el nombre el nombre dela persona que llama y el número de identificador del teléfono. Operación NOTA: Si usted está utilizando el altavoz, oprima el botón de interfono...
Page 79 - Para Desconectar a una Persona; Identificador de Llamadas; Para Desconectar Ambas Personas:; Para Localizar Todas las Estaciones; Pantalla Sumario
31 Para Desconectar a una Persona Oprima el botón de línea o el de interfono de la persona con la que usted quiera seguir conversando, y la otra persona será desconectada automáticamente. Identificador de Llamadas Para Desconectar Ambas Personas: Cuelgue el auricular, u oprima el botón de altavoz (“...
Page 80 - Para Recibir y Almacenar Archivos del Identificador de Llamadas
32 llama aparece en la pantalla Identificador de Llamadas Para Recibir y Almacenar Archivos del Identificador de Llamadas Este aparato recibe y muestra información transmitida por su compañía telefónica local. Esta información puede incluir el número telefónico, fecha y hora; o elnombre, número tele...
Page 81 - Para Borrar un Archivo del Identificador de Llamadas
33 Para almacenar información en el Registro de Interfono/Memo, oprima uno de los botones del registro de memoria (1-16). Identificador de Llamadas Para Borrar un Archivo del Identificador de Llamadas Para borrar el archivo que aparece en la pantalla, oprima el botón de borrar (“DELETE”) una vez. Pa...
Page 82 - Si Usted No Programó su Clave de Área
34 ejemplo 1-425-555-5555). 4. Para marcar el número telefónico mostrado, levante el auricular u oprima nuevamente el botón para marcar (“DIAL ”). Identificador de Llamadas Si Usted No Programó su Clave de Área 1. Utilice los botones para revisar (“REVIEW < o >”) para mostrar el número que ust...
Page 83 - Memoria; Para Revisar La Memoria del Libreo Telefónico (Directorio)
35 NOTA: Si usted comete un error, utilice los botones para revisar (“REVIEW < o >”) para mover el cursor al dígito incorrecto, y oprima el botón “DELETE” para borrar. 3. Oprima el botón para seleccionar (“SELECT”) y la indicación de que inscriba nombre aparece en la pantalla (“INSCRIBA NOMBRE...
Page 84 - Para Almacenar el Último Número Marcado
36 las letras correspondientes para la memoria que usted quiera revisar. Por ejemplo, oprima la tecla del 5 para mostrar las memorias del libro que empiezancon la letra J. Oprima dos veces la tecla del 5 para ir a las memorias del libro que empiezan con la letra K. 3. Oprima el botón de salida (“EXI...
Page 85 - Para Almacenar una Pausa en la Memoria; Para Borrar/ Limpiar Memorias
37 5. Oprima el botón para almacenar (”STORE”). La indicación INSCRIBA LOCALIZ aparece en la pantalla. 6. Oprima el botón de directorio (“DIRECTORY”) para almacenar el número que volverá a marcarse en la memoria del Libro Telefónico u oprima el botón deregistro del Interfono/Memo (1-16) para almacen...
Page 86 - Para Borrar Todas la Memorias
38 2. Utilice los botones para revisar (“REVIEW < o >”) para ver la memoria que usted quiere borrar. 3. Oprima el botón para borrar (“DELETE”) y borre. La indicación de borrar (“DELETE”) aparece en la pantalla. 4. Oprima nuevamente el botón para borrar (“DELETE”) para confirmar. Memoria Para b...
Page 87 - Otra Información; Mensajes en la Pantalla del Identificador de Llamadas
39 Este proceso le permite marcar una sucesión de números almacenados en localizaciones de memoria separadas. Esto es útil cuando usted debe marcar variassecuencias de números, como cuando hace llamadas frecuentes a través de una compañía de larga distancia. Otra Información Por ejemplo Localización...
Page 88 - Operación de las Baterías; Solución de Problemas
40 La corriente de las baterías está baja. (No es aplicable al modelo 25403). Otra Información Operación de las Baterías Si el cable de corriente no está conectado dentro del aparato, y la batería está disponible, el aparato entra en la función de Modalidad de Operación porBaterías. En esta modalida...
Page 90 - Cuidado General del Producto; Cómo Obtener Servicios de Mantenimiento
42 Teléfono con Identificador (Estación del Identificador )” Otra Información Cuidado General del Producto Para mantener su teléfono funcionando bien y con buena apariencia, observe las siguientes pautas: • Evite poner el teléfono cerca de calentadores (calefactores) de ambiente y dispositivos que g...
Page 91 - Garantía Limitada
43 Otra Información Garantía Limitada Lo que cubre su garantía: • Defectos de materiales o de trabajo. Por cuánto tiempo después de la compra: • Un año, a partir de la fecha de compra. (El periodo de garantía para unidades arrendadas se inicia con la primera renta o 45 días de la fecha del embarque ...
Page 93 - Para Ordenar; Formulario para Hacer Pedidos de Accesorios
45 Para Ordenar Para hacer su orden por teléfono, tengasu tarjeta Visa, MasterCard o Discoverlista y llame al número sin cargo queaparece a continuación. Utilice este número únicamente parahacer una orden de artículos accesoriosenlistados en este formulario. 1-800-338-0376 Para hacer su orden por co...
Page 94 - Índice
46 Índice G Garantía Limitada 43 I Identificador de Llamada en Espera 34 Identificador de Llamadas 31Identificador de Llamadas (CID) 31Identificador del Teléfono 15Idioma 13Indicaciones Importantes para la Instalación 8 Información de Interferencias 2Información Importante 2Informacion Importante pa...