Page 2 - Equipment Approval Information; Notification to the Local Telephone Company; Important Information
2 Equipment Approval Information Your telephone equipment is approved for connection to the Public Switched Telephone Network and is in compliance with parts 15 and 68, FCC Rules and Regulations and the Technical Requirements for Telephone Terminal Equipment published by ACTA.1 Notification to the L...
Page 3 - Rights of the Telephone Company; Interference Information
Important Information 2 Rights of the Telephone Company Should your equipment cause trouble on your line which may harm the telephone network, the telephone company shall, where practicable, notify you that temporary discontinuance of service may be required. Where prior notice is not practicable an...
Page 4 - operated with a minimum distance of 20 centimeters between the; Information for DECT Product; This telephone is compliant with the DECT 6.0 standard which
Notice: The changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. Licensing Licensed under US Patent 6,427,009. Hearing Aid Compatibility This telephone system meets FCC standards for Hearing Aid Compatibilit...
Page 5 - Table of Contents
5 E quipmEnt A pprovAl i nformAtion ............... 2 i ntErfErEncE i nformAtion ........................... 3 l icEnsing .................................................. 4 H EAring A id c ompAtibility ......................... 4 fcc rf r AdiAtion E xposurE s tAtEmEnt ...... 4 i nformAtion for dEc...
Page 7 - Introduction; CAUTION: When using telephone equipment, there are basic; in your home goes out.; Parts Checklist; ONE; Telephone Jack Requirements
Introduction CAUTION: When using telephone equipment, there are basic safety instructions that should always be followed. Refer to the IMPORTANT SAFETY INSTRUCTIONS provided with this product and save them for future reference. IMPORTANT: Because cordless phones operate on electricity, you should ha...
Page 8 - Installation; Digital Security System; ringing, unauthorized access, and charges to your phone line.; Important Installation Guidelines; microwave ovens, heating appliances and direct sunlight.
Connections & Setup Installation Digital Security System Your cordless phone uses a digital security system to protect against false ringing, unauthorized access, and charges to your phone line. INSTALLATION NOTE: Some cordless telephones operate at frequencies that may cause or receive interfer...
Page 9 - Handset Layout
Connections & Setup Handset Layout display DND/Privacy (button) Spk (Speaker button) DIR (button) CID (button) 3 Soft keys VOL +/- (buttons) Talk (button) Off (button) Redial (button) Menu/Flash (button) Exit (button) Int/Hold (button) Mute/Del (button) Visual Indicator * Tone (button) #Pause (b...
Page 10 - Base Layout
10 Base Layout Connections & Setup DND/Privacy (button) Delete (button) Exit (button) 3 Soft Keys Play/Stop (button) Memo (button) Ans Sys (button) DIR (button) CID (button) Vol +/- (buttons) Line 1 & 2 (buttons) Intercom (button) Page (button) Redial (button) Hold (button) Headset (button) ...
Page 11 - Installing the Phone; Installing the Handset Battery; NOTE: You must connect the handset battery before use.; CAUTION: To reduce the risk of fire or personal injury, use only; be inserted only one way.; BATTERY
11 Connections & Setup Installing the Phone Installing the Handset Battery NOTE: You must connect the handset battery before use. CAUTION: To reduce the risk of fire or personal injury, use only the Thomson Inc. approved Nickel-metal Hydride (Ni-MH) battery model 5-2734, which is compatible with...
Page 12 - Base Station; user’s guide. This power adaptor is intended to be correctly
12 Base Station The phone may be connected to two line (RJ14C) wall jacks to accommodate all two lines.1. Choose an area near an electrical outlet and a telephone wall jack (RJ11C), and place your cordless telephone on a level surface, such as a desktop or tabletop, or you may mount it on the wall. ...
Page 14 - Programming the Phone; Standby Screen; clock is not set. Please go to menu “Phone Setting- Date /Time” to set the; Programming Functions; programming and return to standby screen.; OFF; Phone Setting; Programming the Telephone
1 5. Place the handset in the base cradle. The charge indicator illuminates, verifying the battery is charging. 6. Allow the phone to charge for 14 hours prior to first use. If you don’t properly charge the phone, battery performance is compromised. NOTE: If the model you bought is a RE2 version, th...
Page 15 - Saved”; Auto Answer (only applicable for handset); From the Phone Setting Menu:; Auto Answer; VOL; Off
15 Area Code (base only), Registration (handset only), De-Registration (base only),2nd Call Alert (both base and handset), Handset Name (handset only),Update HS List (base only). Date/Time From the Phone Setting Menu: 1. Press the VOL (- or +) button to scroll to Date/Time . 2. Press SELECT soft key...
Page 16 - Auto Answer Intercom (applicable for base and handset); NOTE: The Dial mode only can be set in the base menu.; From the Phone setting Menu:; Registration (only applicable to handset); show “PRESS “REG” TO INITIATE REGISTRATION” once the handset has been
1 Auto Answer Intercom (applicable for base and handset) If it is set to on, this handset or base will auto answer the intercom call when it receives an intercom call. From the Phone Setting Menu: 1. Press the VOL (- or +) button to scroll to Auto Answer Int. 2. Press SELECT soft key. Use the VOL (-...
Page 17 - Register; Remove Handset
1 Register From the Phone Setting Menu: 1. Press the VOL (- or +) button to scroll to Register . 2. Press SELECT soft key. “Press base unit page button until beep” shows in the display. 3. Press and hold the Page button on base for 5 seconds. 4. “Registration” displays to indicate the base is now in...
Page 18 - nd Call Alert; Handset Name (only applicable for handset); NOTE: If you make a mistake, press DIR/CID button to move the cursor; Update Handset List (only applicable for base); Display Setting
1 2nd Call Alert If it is set to On, you will hear the alert tone when you are in conversation and there is an incoming call from another line. From the Phone Setting Menu: 1. Press the VOL (- or +) button to scroll to 2ND Call Alert . 2. Press SELECT soft key. Use the VOL (- or +) button to scroll ...
Page 19 - Language; Contrast; From the Display Setting Menu:; Sound Setting; From the Sound Setting Menu:
1 Language From the Display Setting Menu: 1. Press the VOL (- or +) button to scroll to the Language . 2. Press SELECT soft key. 3. Use the VOL (- or +) button to select English, Francais or Espanol . The default setting is English . 4. Press SELECT soft key to save your selection. Contrast From the...
Page 20 - Ring Volume; Key Tone; From the Sound Settings Menu:; Answering System (only applicable for base); From the Answering System Menu:
20 Ring Volume There are 5 volume levels and OFF for your selection. The Ring volume can be set individually for each line. From the Sound Settings Menu: 1. Press the VOL (- or +) button to scroll to the Ring Volume . 2. Press SELECT soft key. 3. Use the VOL (- or +) button to scroll to your selecti...
Page 21 - OGA Playback; OGA Record; Set OGA; NOTE: If you select the option “TIMED” when there is an incoming call,; Set Office Time
21 OGA Playback From the Answering System Menu: 1. Press the VOL (- or +) button to scroll to the OGA Playback . 2. Press SELECT soft key.3. Use left and right button to toggle between Line 1 and Line 2 and use VOL (- or +) button to scroll to your selection. 4. Press SELECT soft key to play the sel...
Page 22 - Set Work Hours; Set After Hours
22 Set Work Hours This will allow you to program the start time for the working hour. From the Answering System Menu: 1. Press the VOL (- or +) button to scroll to the Set Work Hours . 2. Press SELECT soft key.3. Use the touch-tone pad to set the time, and use AM/PM soft key to select AM or PM . 4. ...
Page 23 - Ring Delay; incoming call after 5 rings.; Message Length; Call Screening; Message Alert
2 Ring Delay This feature lets you select the number of times you want the phone to ring before the answering system answers a call. From the Answering System Menu: 1. Press the VOL (- or +) button to scroll to the Ring Delay . 2. Press SELECT soft key. 3. Use the VOL (- or +) button to scroll to yo...
Page 24 - Remote Password; Restore Setting; Telephone Operation; Making Calls with the Cordless Handset; Making Calls in the Speakerphone mode (from the base); hung up. The timer serves for both 2 lines.; Telephone Operation
2 Remote Password You can access the answering system from a tone dialing telephone in another (remote) location. The security code is required for remote access, and it prevents unauthorized access to your answering system. From the Answering System Menu: 1. Press the VOL (- or +) button to scroll ...
Page 25 - telephone number; Answering a Call
25 Making Call in the Speakerphone mode (from the handset) 1. Press the Speaker button to activate the speakerphone on the first available line. -OR- Press the LINE 1 or LINE 2 soft key to select a specific line. The handset will activate the ear piece. 2. Press the Speaker button to switch to speak...
Page 26 - Base; Mute; NOTE: When using the mute feature on the base, the indicator will
2 For the base: 1. Press the Speaker button to answer the call in speakerphone mode, -OR- 2. Press the corresponding Line button to answer the call in speakerphone mode, -OR- 3. Press the Headset button to answer the call in headset mode. 4. When finished, press Speaker button (in speakerphone) or H...
Page 27 - Do Not Disturb; the intercom call even if the Do Not Disturb function is activated.; Flash; Press a; Line; button to select a line.; Reviewing the Redial Numbers
2 Do Not Disturb This feature is set at individual telephones to disable (silence) an incoming ring signal, intercom ring. When there is an incoming call or an intercom call, the status indicators function as normal but the phone will not ring.1. When the unit is idle, press the DND/Privacy button. ...
Page 28 - the number is dialed accordingly.; Storing a Redial Record in Phone Book; Enter Name”; Transferring a Call to Another Extension; ”Unavailable”; Receiving a Transferred Call from Another Extension; “Intercom call from base/Handset; Ringer On/Off and Ringer Volume
2 NOTE: If you do not select a Line button, the line is automatically seized and the number is dialed accordingly. Storing a Redial Record in Phone Book 1. Make sure the phone is OFF (not in Talk mode). 2. Press the Redial button, then use the VOL (- or +) button to scroll to the desired redial numb...
Page 29 - “Line X ON HOLD”; Conference Calls; Join a call in progress:; joined by another user.; -way conference call by an intercom call:
2 Speakerphone, Handset, and Headset Volume While the phone is in use, during the desired mode, press the VOL (+ or -) buttons until you reach a comfortable listening level. The phone stores the setting after the last button pressed. Hold In Talk mode, press the Hold button to hold the line. “Line X...
Page 30 - Intercom; shows in the display.; Answering an Intercom Call; Page; Page; Auto Standby; Intercom Calls
0 3. The originating caller can then press the CONF soft key shown on the display to initiate a conference. Since Line 1 and 2 are both on hold, the user will be prompted to select Line 1, Line 2 or Both to conference with. The user can then use the soft keys to select the desired option. If the BOT...
Page 31 - Caller ID; Base Display; Receiving and Storing CID Records; NEW”; Reviewing CID Records; CID
1 Caller ID (CID) IMPORTANT: In order to use this unit’s Caller ID features, you must subscribe to either the standard Name/Number Caller ID Service or Call Waiting Caller ID Service. To know who is calling while you are on the phone, you must subscribe to Call Waiting Caller ID Service. When the un...
Page 32 - Saving a CID Record to Phone Book Memory; Deleting a CID Record; Delete All CID Records?”; Dialing Back; If You Programmed Your Local Area Code
2 Saving a CID Record to Phone Book Memory 1. While viewing a CID record, press the STORE soft key. 2. The name shows in the display. You can edit it. After editing, press the SAVE soft key. 3. The number shows in the display. You can edit it. After editing, press the SAVE soft key. 4. You can selec...
Page 33 - If You Did Not Program Your Local Area Code; Call Waiting Caller ID; Service. To know who is calling while you are on the phone, you must; Memory Log and Phone Book (Directory) Memory; Adding Phone Book Entries; Memory
Number of digits Explanation Example 7-digits: 7-digit telephone number (i.e.555-5555) 10-digits: 3-digit area code +7-digit telephone (i.e.425-555-5555) number 11-digits: long distance code 1 (i.e. 1-425-555-5555) +3-digit area code +7-digit telephone number 4. To dial the displayed number, select ...
Page 34 - Storing Record in One-Touch Dialing; Select Button Location”; Reviewing Phone Book Records; “Handset Name”
7. Use VOL (- or +) button to scroll to the selection and press SELECT soft key to complete. NOTE: If “Memory full” shows in the display, you should delete one or more unnecessary records and repeat above steps to continue the call record storage. Storing Record in One-Touch Dialing (Only applicable...
Page 35 - NOTE: Press the BACK soft key to keep the previous setting (making no; Copying a Phonebook Record; Deleting a Phone Book Record; Deleting All Phone Book Records; DIR
5 5. Press SELECT soft key to complete. NOTE: Press the BACK soft key to keep the previous setting (making no changes). Copying a Phonebook Record You can copy one phone book record or the whole phone book from the handset extension to the base or from the base to desired handset extension. In the e...
Page 36 - Dialing a Phone Book Record; Dial a phone book record while in Talk mode:; Answering System On/Off; Answering System Operation
Dialing a Phone Book Record Dial a phone book record while in Talk mode: 1. Make sure the phone is ON (in Talk mode) by pressing the Talk , Spk button, or selecting a Line. 2. Press the DIR button to access the phone book. 3. Use the VOL (- or +) button or the number keys to scroll to the desired re...
Page 37 - there is a steady dial tone for 7 seconds.; Monitoring Incoming Calls; length setting in the menu.; Memo Recording (Only applicable for base); From the Answer System Menu:; Message/Memo Playback
NOTE: Your unit will record a message up to the maximum length of time you set as long as the caller continues speaking. To save recording capacity, your unit will automatically stop recording after 7 seconds of silence or if there is a steady dial tone for 7 seconds. Your unit can record up to 60 m...
Page 38 - “You have NO messages”; Erasing Messages; To erase a message while it is playing; Delete message xx”; To erase all previously played messages in a mailbox; Delete all messages in; Remote Access From Remote Party
During each message playback, it shows the current message information on the screen. If the message playback is a stored incoming message, it shows the message’s CID, including Date/Time, Name and Number. If it is a memo, only Display memo and Date/Time.During each message playback, you can press t...
Page 39 - Memory Full; “Memory full”; Changing the Battery
5. To exit remote operation, hang up. The system will automatically disconnect the call if the user does not enter a command within 10 seconds. NOTE: Only the message being played can be erased in remote access mode. Memory Full When the answering system memory is full, the system answers after 10 r...
Page 41 - Troubleshooting Guide; Telephone Solutions; TONE; Other Information
1 Troubleshooting Guide Telephone Solutions No dial tone • Check or repeat installation steps: Make sure the base power cord is connected to a working electrical outlet. Make sure the telephone line cord is connected to the base and the wall jack. • Connect another phone to the same jack. If it does...
Page 42 - Caller ID Solutions; No Display; Disconnect the power adaptor from the base and reconnect it.; No Caller ID; from your local telephone company to receive CID information.; Battery; General Product Care; alcohol, or other chemical products to clean the unit. Doing so will
2 Caller ID Solutions No Display • Charge the battery (for 14 hours). Or replace the battery.• Make sure the unit is connected to a non-switched electrical outlet. Disconnect the power adaptor from the base and reconnect it. No Caller ID • You must be subscribed to the standard Name/Number Caller ID...
Page 44 - please contact customer service at; Manager, Consumer Relations
Warranty Warranty Assistance If trouble is experienced with this equipment, for warranty information, please contact customer service at 1-800-511-3180 . If the equipment is causing harm to the telephone network, the telephone company may require that you disconnect the equipment until the problem i...
Page 45 - What your warranty covers:
Warranty Limited Warranty What your warranty covers: • Defects in materials or workmanship. For how long after your purchase: • Two years, from date of purchase. (The warranty period for rental units begins with the first rental or 45 days from date of shipment to the rental firm, whichever comes fi...
Page 46 - Warranty; the above limitations or exclusions may not apply to you.
Warranty Limitation of Warranty:• THE WARRANTY STATED ABOVE IS THE ONLY WARRANTY APPLICABLE TO THIS PRODUCT. ALL OTHER WARRANTIES, ExPRESS OR IMPLIED (INCLUDING ALL IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE) ARE HEREBY DISCLAIMED. NO VERBAL OR WRITTEN INFORMATION GIVE...
Page 47 - availability. Prices are subject to change without notice.; DESCRIPTION; Handset Replacement Battery
Accessory Information Accessory Information To place order, have your Visa, MasterCard, or Discover Card ready and call toll-free 1-800-338-0376. A shipping and handling fee will be charged upon ordering. We are required by law to collect appropriate sales tax for each individual state, country, and...
Page 48 - Index
A 2nd Call Alert 18 3-way conference call by an intercom call 29 3-way conference call with two lines 29 4-way conference call (Line 1 + Line 2 + 2 extension) 29 Accessory Information 47 Adding Phone Book Entries 33 Answering a Call 25 Answering an Intercom Call 30 Answering System 20 Answering Syst...
Page 51 - Por favor lea este manual
Teléfono con Altavoz de Dos Líneas DECT 6.0 Sistema de Auricular Inalámbrico y Altavoz con Contestador Guía del Usuario Por favor lea este manual antes de operar este producto por primera vez. Modelo 25250
Page 52 - Información sobre la Aprobación de Equipo; Notificación a la Compañía Telefónica Local; Derechos de la Compañía Telefónica; Información Importante
2 Información sobre la Aprobación de Equipo El equipo de su teléfono esta aprobado para la conexión con la red Telefónica Pública (Public Switched Telephone Network) y cumple con los requisitos establecidos en las secciones 15 y 68 de las Reglas y Regulaciones de la FCC y con los Requerimientos Técn...
Page 53 - Licensing
Información Importante Información de Interferencias Este artefacto cumple con la Parte 15 de las Reglas de la FCC. Su funcionamiento es sujeto a las dos condiciones siguientes: (l) Este artefacto no puede causar interferencia dañosa, y (2) Este artefacto debe aceptar cualquier interferencia recibid...
Page 54 - Declaración de la FCC sobre Exposición a la Radiación RF; Información para el Producto DECT (Teléfono Inalámbrico
Declaración de la FCC sobre Exposición a la Radiación RF Este equipo cumple con los límites a la exposición de radiación RF de la FCC establecidos para un ambiente no controlado. Este equipo deberá ser instalado y operado a una distancia mínima de 20 centímetros entre el radiador y su cuerpo. Este t...
Page 55 - fcc; Tabla de Contenido
5 I nformacIón sobre la a probacIón de e quIpo 2 I nformacIón de I nterferencIas .................... 3 c ompatIbIlIdad con a udífonos (cca)......... 3 l IcensIng .................................................. 3 d eclaracIón de la fcc sobre e xposIcIón a la r adIacIón rf ................. 4 I nf...
Page 57 - Introducción; CUIDADO: Cuando use equipo telefónico, hay instrucciones; usted debe tener por lo menos un teléfono en su casa que no sea; Conexión y Programación; UN; Requerimientos de Enchufe Telefónico
Introducción CUIDADO: Cuando use equipo telefónico, hay instrucciones básicas de seguridad que siempre deben seguirse. Refiérase a la sección INSTRUCCIONES IMPORTANTES DE SEGURIDAD provistas con este producto y guárdelas para referencia en el futuro. IMPORTANTE: Como los teléfonos inalámbricos opera...
Page 58 - Sistema Digital de Seguridad; timbrado falso, el uso no autorizado y cargos a su línea telefónica.; Indicaciones Importantes para la Instalación; • Evite fuentes de ruido y calor, como motores, hornos de micro ondas, o
Conexión y Programación Instalación Sistema Digital de Seguridad Su teléfono inalámbrico usa un sistema de seguridad digital para evitar el timbrado falso, el uso no autorizado y cargos a su línea telefónica. NOTA SOBRE LA INSTALACIÓN: Algunos teléfonos inalámbricos operan a frecuencias que pueden c...
Page 61 - Instalar la Batería del Auricular; PRECAUCION: Para reducir el riesgo de fuego o lastimaduras; Localice el compartimento de la batería en la parte
11 Conexión y Programación Instalación del Teléfono Instalar la Batería del Auricular NOTA: Usted debe conectar la batería del auricular antes de utilizar el aparato. PRECAUCION: Para reducir el riesgo de fuego o lastimaduras personales, use solamente la batería de Níquel- Hidruro Metálico (Ni-MH) m...
Page 62 - Estación Base; para teléfono (RJ11C), y coloque su teléfono inalámbrico en una; CUIDADO: Para reducir el riesgo de lesión personal, fuego, o; receptáculos en la parte posterior del teléfono.
12 Estación Base El teléfono puede ser conectado a dos receptáculos de pared para dos líneas (RJ14C) para acomodar las dos líneas.1. Elija un área cerca de una toma eléctrica y de un receptáculo de pared para teléfono (RJ11C), y coloque su teléfono inalámbrico en una superficie nivelada, tal como un...
Page 63 - líneas tal como se indica en el siguiente diagrama
1 4. Si usted quiere montar el teléfono en la pared, puede conectar las 2 líneas tal como se indica en el siguiente diagrama; Conexión y Programación ‑O‑ ‑O‑ Linea 1 Linea 2 Linea 1 Linea 2 Lineas 1 + 2
Page 64 - comprobando que la batería está cargando.; Pantalla en Espera; NOTA: Durante la programación, usted puede presionar en cualquier; Configuración de Teléfono; Configuración de; Programación del Teléfono
1 5. Coloque el auricular en la base. El indicador de carga se ilumina, comprobando que la batería está cargando. 6. Permita que el teléfono cargue por 14 horas antes del primer uso. Si usted no carga apropiadamente el teléfono, el desempeño de la batería puede verse disminuido. NOTA: Si el modelo q...
Page 65 - “Guardado”
15 4. Presione la tecla de función programable SELECT (derecha) para confirmar y usted puede programar los elementos siguientes: Fecha/Hora (solamente la base), Respuesta Automática (solamente el auricular), Intercomunicación Respuesta Automática (tanto en la base como en el auricular), Modo Marcaci...
Page 66 - Respuesta Automática (solamente el auricular); Intercomunicación Respuesta Automática (tanto en la base; Desde el Menú de Configuración de Teléfono:
16 Respuesta Automática (solamente el auricular) Esta opción le permite levantar el auricular de la base para responder una llamada entrante sin presionar el botón Talk/Spk/L1/L2 . Cuando está apagada, esta función está inhabilitada en el auricular. Desde el Menú de Configuración de Teléfono: 1. Pre...
Page 67 - mostrará “PRESIONE “REG” PARA INICIAR EL REGISTRO” una vez que el; Registro
1 Código de Area (solamente la base) El teléfono usa un código de área preprogramado para determinar el formato del número a visualizar cuando un registro de Identificador de Llamada válido se recibe. El Código de Area preprogramado es usado también para la modalidad de Retorno de Llamada. Desde el ...
Page 68 - Para Remover el Registro de un Auricular; entrar nuevamente al modo de registro.; Alerta de 2a. Llamada
1 Para Remover el Registro de un Auricular La remoción del registro cancela el registro. Durante el proceso de remoción de registro, mantenga el auricular cerca de la base. ADVERTENCIA: No se recomienda la remoción de registro de un auricular a menos que sea absolutamente necesario, ya que una vez q...
Page 69 - Nombre de Auricular (solamente el auricular); retroceder y eliminar un caracter a la vez.; Actualizar Lista de Auricular (solamente la base); Configuración de Pantalla
1 Nombre de Auricular (solamente el auricular) Desde el Menú de Configuración de Teléfono: 1. Presione el botón VOL (‑ ó +) para desplazarse a Nombre de Auricular . 2. Presione la tecla de función programable SELECT. El nombre predeterminado es Auricular . 3. Use el teclado de tonos para ingresar un...
Page 70 - Idioma; Contraste; Desde el Menú de Configuración de Pantalla:; Configuracion de Sonido
20 Idioma Desde el Menú de Configuración de Pantalla: 1. Presione el botón VOL (‑ ó +) para desplazarse a Idioma . 2. Presione la tecla de función programable SELECT. 3. Use el botón VOL (‑ ó +) para seleccionar Inglés , Francés , Español . La configuración predeterminada es Inglés . 4. Presione la ...
Page 71 - Tono de Timbre; Volumen de Timbre; Desde el Menú Configuración de Sonido:; Tono de Tecla; Desde el Menú Configuración de Sonido:; Sistema de Contestadora (solamente la base)
21 Tono de Timbre Hay 8 niveles de tono para su selección. Estos son Melodía 1 a 8 para Línea 1 y Línea 2 respectivamente. Desde el Menú Configuración de Sonido: 1. Presione el botón VOL (‑ ó +) para desplazarse a Tono de Timbre . 2. Presione la tecla de función programable SELECT. 3. Use el botón V...
Page 72 - Reproducción OGA; Desde el Menú del Sistema de Contestadora:; Registro OGA; Desde el Menú del Sistema de Contestadora:; Configuración del OGA; Desde el Menú del Sistema de Contestadora:
22 Estado On/Off Esto es usado para encender o apagar el sistema de contestadora para cada línea telefónica en forma individual. Desde el Menú del Sistema de Contestadora: 1. Presione el botón VOL (‑ ó +) para desplazarse a Estado On/Off . 2. Presione la tecla de función programable SELECT. 3. Use e...
Page 73 - según el horario de oficina que usted establezca.; Configuración de Horas de Oficina; Configuración de las Horas Hábiles; Configuración de Horas Inhábiles
2 NOTA: Si usted selecciona la opción “Por Tiempo” cuando haya una llamada entrante, el OGA “Horas Hábiles” o el OGA “Horas Inhábiles” se visualizará según el horario de oficina que usted establezca. Configuración de Horas de Oficina Desde el Menú del Sistema de Contestadora: 1. Presione el botón VO...
Page 74 - Demora del Timbre; unidad responderá la llamada entrante después de 5 timbres.; Duración del Mensaje; Filtración de Llamada
2 Ejemplo: a) Establecer las Horas Hábiles para iniciar a las 9:00 a.m., y “Sólo Anuncio” como NO. b) Establecer las Horas Inhábiles para iniciar a las 5:00 p.m., y “Sólo Anuncio” como NO. c) Seleccione “Por Tiempo” al seleccionar el OGA. Cuando la llamada llegue dentro de las 9:00 a.m. a 5:00 p.m.,...
Page 75 - Alerta de Mensaje; Clave de Acceso Remoto; Para Restaurar Configuración; Desde el Menú Restaurar Configuración:
25 Alerta de Mensaje Esta característica configura su sistema de contestadora para dar un tono de alerta cada 10 segundos cuando haya nuevo mensaje. Desde el Menú del Sistema de Contestadora: 1. Presione el botón VOL (‑ ó +) para desplazarse a Alerta de Mensaje . 2. Presione la tecla de función prog...
Page 76 - Para hacer Llamadas con el Auricular Inalámbrico; Operación del Teléfono
26 Operación del Teléfono Para hacer Llamadas con el Auricular Inalámbrico 1. Presione el botón Talk , la unidad tomará la primera línea disponible para usted. ‑O‑ Presione la tecla de función programable Line 1 ó Line 2 para seleccionar una línea que usted desee. 2. Espere el tono de marcación y lu...
Page 77 - Premarcación
2 5. Para el auricular inalámbrico, presione el botón Talk . 6. Espere el tono de marcación, y luego marque el número telefónico.7. Presione el botón Headset (en base) o el botón End (en el auricular) al terminar. CUIDADO: Use únicamente el auricular Thomson Inc. 5-2425 que son compatibles con este ...
Page 78 - Para Alternar Entre el Modo Altavoz, Auricular y Audífono; Silencio; iluminará cuando la opción de silencio sea activada.; No Molestar; función No Molestar está activa.
2 Para Alternar Entre el Modo Altavoz, Auricular y Audífono Base Para cambiar al altavoz, presione el botón Spk . El indicador altavoz se ilumina.Para cambiar al audífono, presione el botón Headset para activar el audífono, y el indicador de audífono se ilumina. Auricular Inalámbrico Para cambiar al...
Page 79 - para seleccionar una línea.; Revisión de los Números de Remarcación; tomada y el número es marcado según corresponda.; Para Almacenar un Registro de Remarcación en el Directorio; “Ingresar Nombre”
2 Inserción de una Pausa en la Secuencia de Marcación Presione el botón #pause dos veces para insertar una demora en la secuencia de marcación cuando se necesite una pausa para esperar un tono de marcación (por ejemplo, después de marcar el 9 para tener acceso a una línea externa, o para esperar el ...
Page 80 - Transferencia de una Llamada a otra Extensión; ”No Disponible”; Para Recibir una Llamada Transferida desde otra Extensión; “Llamada de intercomunicación de la base/auricular x”; Timbre On/Off y Volumen de Timbre; NOTA: Si usted elige timbre OFF, “L1/L2 TIMBRE OFF” se muestra en la; Volumen de Altavoz, Auricular y Audífono
0 6. Usted puede editar el número de teléfono.7. Presione la tecla de función programable SAVE para entrar a la selección de Melodía de Tono VIP. Transferencia de una Llamada a otra Extensión 1. Presione la tecla de función programable XFER cuando el teléfono esté en modo Hablar. 2. Use VOL (‑ ó +) ...
Page 81 - Retención; “Línea X en; Llamadas de Conferencia; Para unirse a una llamada en progreso:; otro usuario no puede unirse a esta llamada.; Llamada de conferencia de 3 vías mediante una llamada de
1 Retención En modo Hablar, presione el botón Hold para retener la línea. “Línea X en retención” se muestra en la pantalla, y el ícono de línea parpadeará. En la base, el indicador de botón Line parpadeará también. Cuando la línea esté en retención, el tono de alerta de retención será emitido.Presio...
Page 82 - Intercomunicación de un Toque; error y “No disponible” se muestra en la pantalla.; Para Responder una Llamada de Intercomunicación; Llamadas de Intercomunicación
2 Llamada de conferencia de 4 vías (Línea 1 + Línea 2 + 2 extensiones): 1. Una vez que la unidad base o el auricular tenga tanto la Línea 1 como la Línea 2 en retención, presione el botón Intercom y luego seleccione el auricular o base deseada para intercomunicación. 2. El auricular o base seleccion...
Page 83 - Búsqueda; “Buscando desde la Base”; Nombre/Número estándar o al servicio de Identificador de Llamada; Identificador de Llamada; Exhibición de Base; Recepción y Almacenamiento de Registros CID; “NUEVO”
Búsqueda La característica de búsqueda le ayuda a ubicar un auricular extraviado. 1. Presione el botón Page en la base. El auricular emite bips y el Indicador Visual en el auricular parpadea. “Buscando desde la Base” se muestra en la pantalla del auricular. 2. Para cancelar la búsqueda, presione el ...
Page 84 - Para Eliminar un Registro CID; “Registro eliminado!”; Para Eliminar Todos los Registros de Llamada; “Eliminar todos los registros CID?”
Revisión de Registros CID • Presione el botón CID , y luego use el botón VOL (‑ ó +) para desplazarse a través de los registros de llamada. • Cuando usted se desplaza al inicio/fin de la listan, “--INICIO/FIN--” aparece en la pantalla. • Al revisar los registros CID, el número de registros se muestr...
Page 85 - Marcación de Regreso de Llamada; Si usted Programó su Código de Área Local; Número de Dígitos Explicación; Si usted No Programó su Código de Área Local; Llamada en Espera Identificador de Llamada
5 Marcación de Regreso de Llamada Al revisar los registros CID, usted puede marcar para regresar la llamada usando los números que se muestran en la pantalla presionando el botón Headset, o el botón Talk , o el botón Spk o el botón Line 1 ó Line 2 . Si usted Programó su Código de Área Local 1. Use e...
Page 86 - Bitácora de Memoria y Memoria del Directorio Telefónico; Para Añadir Registros del Directorio Telefónico; Para Almacenar un Registro en Marcación de un Toque; Memoria
6 Bitácora de Memoria y Memoria del Directorio Telefónico Usted puede almacenar datos en el directorio telefónico (hasta 99 registros en memoria) o en (Intercomunicación/Memoria) Intercom/Memory (10 botones ubicados a la derecha del teclado numérico en la base). El directorio telefónico y cada bitác...
Page 87 - Para Revisar Registros del Directorio Telefónico; Para Editar un Registro del Directorio Telefónico; “Nombre de Auricular”; Para Copiar un Registro del Directorio Telefónico; En el auricular de extensión:; “Copiar registro actual o todo el directorio?”
6. Presione la tecla de función programable SAVE. “ Ingresar número” se muestra en la pantalla. 7. Use el teclado de tonos para ingresar un número de teléfono. TIP: Presione el botón #pause dos veces para insertar una pausa en un número si es necesario. 8. Presione la tecla de función programable SA...
Page 88 - Para Eliminar un Registro del Directorio Telefónico; “Registro eliminado”; Para Eliminar Todos los Registros del Directorio Telefónico; “BORRAR; Para Marcar un Registro del Directorio Telefónico; Sistema de Contestadora
En la Unidad Base: 1. Mientras ve el registro del directorio telefónico, presione la tecla de función programable COPY. 2. “Copiar registro actual o todo el directorio?” se muestra en la pantalla. Presione la tecla de función programable CURR para copiar el registro actual o presione la tecla de fun...
Page 89 - Operación del Sistema de Contestadora; Sistema de Contestadora On/Off; marcación continuo durante 7 segundos.; Monitoreo de Llamadas Entrantes
2. Presione el botón Phonebook para accesar el directorio telefónico. 3. Use el botón VOL (‑ ó +) o las teclas numéricas para desplazarse al registro deseado. 4. Presione el botón Talk o Spk en el auricular o presione el botón Speaker o Line 1 / 2 en la base. El número es marcado en forma automática...
Page 90 - Registro de Memo; NOTA: La duración máxima permitida para memo es la misma que la
0 Registro de Memo Usted puede dejar un mensaje presionando el botón Memo en la base o seleccionando grabación de memo bajo el menú del auricular. 1. Presione el botón Memo en la base o el menú del auricular para ingresar al modo grabación de memo. 2. Use el botón VOL (‑ ó +) para seleccionar Buzón ...
Page 91 - Para Borrar Mensajes; Para borrar un mensaje mientras está en reproducción; “Eliminar mensaje xx”; Delete; “Eliminar todos los; Acceso Remoto desde una Parte Remota; NOTA: El código de seguridad predeterminado es 000.
1 Para Borrar Mensajes Usted puede borrar mensajes en las tres siguientes formas: Para borrar un mensaje mientras está en reproducción 1. Seleccione y reproduzca el mensaje que quiere borrar.2. Presione el botón Delete . La unidad le pedirá que confirme la eliminación. 3. Presione la tecla de funció...
Page 92 - Memoria Llena; “Memoria llena”; Cambiar la Batería; Otra Información
2 Memoria Llena Cuando la memoria del sistema de contestadora está llena, el sistema responde después de 10 timbres. “Memoria llena” será anunciado y espera que usted ingrese un código de seguridad de 3 dígitos. Si usted no ingresa el código de seguridad en 7 segundos, el teléfono cuelga.Usted deber...
Page 94 - Señal Significado; Solución de Problemas; Soluciones para el Teléfono; No hay tono de marcar
Otra Información Señales Sonoras del Auricular Señal Significado Un tono de gorgeo largo Señala una llamada entrante (con el timbre activado) Dis bips cortos Señal de la Página Un tono corto cada 14 segundos Advertencia de baja bateriaUn tono largo Confirmación Un tono de gorgeo corto Tono de Error ...
Page 95 - Soluciones para el Identificador de Llamadas; Nada aparece en la pantalla; Cuidado General del Producto
5 Otra Información El aparato se traba y no hay comunicación entre la base y el auricular inalámbrico • Desconecte el cable de corriente del enchufe eléctrico y de la parte posterior de la base. Quite la batería del auricular. Espere 30 segundos y vuelva a conectar el cable de corriente al enchufe d...
Page 96 - las señales de radio.; Ayuda de la Garantía; comuníquese con el departamento de servicio al cliente al; Gerente, Servicio al Consumidor; durante el período de garantía.; Garantía Limitada; Lo que cubre su garantía:; Por cuánto tiempo después de la compra:
6 Garantía Causas de una Mala Recepción • Recubrimiento externo de la casa con aluminio.• Aislación con revestimiento de papel de aluminio.• Conductos de calefacción y otras construcciones de metal que paran las señales de radio. • Está demasiado cerca de los aparatos eléctricos como microondas, coc...
Page 97 - Garantía; O ESCRITA OTORGADO POR THOMSON INC., SUS AGENTES, O EMPLEADOS SERá
Garantía Cómo obtener servicio: • Empaque bien la unidad, incluyendo todos los cables, etc., que originalmente venían con el producto. Se recomienda usar el cartón y materiales de empaque originales. • “Prueba de compra como factura o recibo de compra, que ofrezca evidencia de que el producto está d...
Page 98 - Indice
A Acceso Remoto desde una Parte Remota 41 Actualizar Lista de Auricular 19 Alerta de 2a. Llamada 18 Alerta de Mensaje 25 Auricular Inalámbrico 28 Auto Standby 33 Ayuda de la Garantía 46 B Base 28 Bitácora de Memoria y Memoria del Directorio Telefónico 36 Búsqueda 33 C Cambiar la Batería 42 Causas de...
Page 100 - dar servicio a su producto.; Información de Accesorios; . Se aplicará un cargo por envío al ordenar. La ley nos requiere; DESCRIPCIóN; Batería de Repuesto
Visite el sitio de RCA en www.rca.com Por favor no envíe ningún producto a la dirección de Indianápolis enlistada en este manual o en la caja. Esto únicamente resultará en un retraso para dar servicio a su producto. Thomson Inc. 101 West 103rd Street Indianapolis, IN 46290‑1102 © 2008 Thomson Inc. T...