QLogic APS-610 - Manual
QLogic APS-610 – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.
Table of Contents:
- Page 2 – INSTALLATION OF MAJOR COMPONENTS; Channel 3 & Alternate Channel 3
- Page 5 – be active as long as the transmitter button is depressed.
- Page 7 – Yellow = Common Relay Contact
- Page 9 – COMPLETING THE INSTALLATION
Model APS-610
Installation Manual
SELECTABLE FEATURES
Note: The method of manual override can either be selected to operate from the valet switch or operate as custom
code. Be certain to place a check mark indicating the method used in the box located on the last page of
the owner's manual.
Note: When both Passive Arming and Voltage Sensing are selected, you must hardwire the driver’s door pin
switch in order to begin the passive arming sequence.
RF Programmable Features :
Feature Selection
1 Chirp
2 Chirps
3 Chirps
4 Chirps
Default
1st Door L/UL
1 Sec.
3.5 Sec.
1 Sec L, Dbl. U/L
1 Sec.
2nd Accy Lock
Auto Lock On
Auto Lock Off
Auto Lock Off
3rd Accy. UL
Auto UL Dr.
Auto UL All
Auto UL Off
Auto UL Off
4th Headlights
On Arm
On Disarm
On Both
Off
Both
5th Passive Locks
Passive
Active
Active
6th Passive/Active Arm
Passive Arm
Active Arm
Active Arm
7th Voltage Sense
Voltage Sense
Hardwire
Hardwire
8th Siren/Horn
Siren/Horn
Siren Only
Horn Only
Siren/Horn
9th Horn Chirp
10mS
16mS
30mS
16mS
10th Override Method
Custom Code
Valet
Valet
11th Two Step Unlock
On
Off
Off
12th Chirp Delete From Tx
On
Off
Off
To program these selectable features;
Action
System Response
Turn ignition on
No response
Press and release the valet switch 3 times
1 Chirp - LED 1 flash
Within 3 seconds, turn ignition Off
Short chirp, then long chirp
First
Then On
1 chirp = 1 second door locks
Press transmitter Lock button to change
2 chirps = 3.5 second door locks
Press transmitter Lock button to change
3 chirps = 1 sec. lock, dbl 1 sec. unlock
or
Second
Press and release the valet switch
2 chirps = auto locks off
Press transmitter Lock button to change
1 chirp = auto locks on
or
Third
Press and release the valet switch
3 chirps = auto unlock off
Press transmitter Lock button to change
1 chirp = auto unlock drivers door only
Press transmitter Lock button to change
2 chirps = auto unlock all doors
or
"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.
Summary
Page 2 Fourth Press and release the valet switch 3 chirps = headlight output when arming and disarming Press transmitter Lock button to change 4 chirps = headlight output off Press transmitter Lock button to change 1 chirp = headlight output when arming Press transmitter Lock button to change 2 chir...
Page 5 Orange Wire: 300 mA Ground Output When Armed - N. C. Starter DisableThis wire is provided to control the starter cut relay. Connect the orange wire to terminal 86 of the relay.Connect relay terminal 85 to an ignition wire in the vehicle that is live when the key is in the on and crankposition...
Page 7 2 Pin White Connector: Dash Mounted L.E.D.Route the red and blue wires in the 2 pin white connector from the L.E.D. to the control module, and plug itinto the mating white connector on the side of the module. 4 Pin White Connector: Shock SensorRoute the red, black, green and blue wires in the...
