Promounts UA-PRO110 - User Manual

IMPORTANT!

For safety reasons, the concrete wall must be

capable of supporting the combined weight of the mount and
the display. The manufacturer takes no responsibility for failure
caused by walls of insufficient strength.

1

2

3

4

INSTRUCTION MANUAL

Display Size:

17” - 42”

Maximum Load:

20 kg (44 lbs)

Mounting Pattern:

100 mm x 100 mm, 200 mm x 100 mm, 200

mm x 200 mm

Tilt Range:

5° up to 15° down

Pan/Swivel Range:

up to 180°

Profile:

5.5 cm - 36.2 cm (2.2” - 14.3”)

(H) M6 x 15 Screw (x4)

(I) M8 x 15 Screw (x4)

(J ) M8 x 30 Screw (x4)

(K) M8 x 50 Screw (x4)

(L) M8 Washer (x4)

(M) Spacer (x4)

(N) S4 Allen Key (x1)

IMPORTANT!

For safety reasons, this mount must be secured

to a wood stud capable of supporting the combined weight of
the mount and display. Do not mount to drywall alone.

1

Place the mount against the wall over the marked stud. Make
sure it is level and right side up.
Mark two locations (one top and one bottom) at the center of
the stud for securing the mount to the wall (see Fig. 2) and set
it aside.
Drill a 3 mm (1/8”) pilot hole at each marked location.
Place the mount back against the wall and attach it using the
drywall screws (A) and two of the washers (B) provided (see
Fig. 3).

Do not over-tighten these screws.

Ensure that the

mount remains level after both screws are secured.

2

3

4

5

Part 1A – Mounting to the Wall (Drywall)

Part 1A – Mounting to the Wall (Drywall) (continued)

SPECIFICATIONS

BOX CONTENTS

HARDWARE KIT

TOOLS REQUIRED

INSTALLATION

PREPARATION

Fig. 4

Read these instructions before you begin.

If you are unsure

of any part of the process, contact a professional contractor or

installer for assistance. Improper installation can result in injury

or damage.
The wall or mounting surface must be capable of supporting

the combined weight of the mount and the display; if not, the

structure must be reinforced.
Locate pipes, wires, or any other hazards in the wall where you

wish to install the mount before drilling.
Safety gear and proper tools must be used. Failure to do so

can result in injury or damage.
Two people are recommended for installation. Do not attempt

to lift a heavy display without assistance.
Follow all instructions and recommendations regarding

adequate ventilation and suitable locations for mounting your

display. Consult the owner‘s manual for your particular display

for more information.

CAUTION:

This wall mount is intended for use only with the

maximum weight of 20 kg (44 lbs). Use with heavier than the

maximum weights indicated may result in instability causing

possible injury.

1

2

3

4

5

6

WARNINGS

Phillips Head Screw Driver
Electric or Portable Drill
3 mm (1/8”) Drill Bit and Stud Finder for Drywall Installation
8 mm (5/16”) Masonry Bit for Concrete Installation
Level

Mount (x1)
Plastic Cover (x2)

Instruction Manual (x1)
Hardware Kit (x1)

Part 1B – Mounting to the Wall (Concrete)

Place the mount against the wall in

the desired location. Make sure it is

level and right side up.
Mark two locations (one top and

one bottom) for securing the mount

to the wall (see Fig. 4) and set it

aside.
Drill an 8 mm (5/16”) hole at each

marked location. Remove any excess dust from the holes.
Insert a concrete anchor (C) into each hole so that it is flush

with the concrete surface (see Fig.5). A hammer can be used

to lightly tap the anchors into place if necessary.

Use a high quality stud finder to locate a stud where you wish
to install your mount. Mark both edges of the stud to help
identify the exact center.

NOTE:

You must use the center of the stud to avoid cracking

or splitting the wood during installation.

Prepare the mount for installation
by disassembling the display plate
from the mount. Do this by
removing the safety screws as
shown (see Fig.1). Place the screws
in a safe location.

Fig. 2

Fig. 3

Fig. 1

(A) Drywall Screw (x2)

(B) Washer (x2)

(C) Concrete Anchor (x2)

(D) M4 x 15 Screw (x4)

(E) M4 x 50 Screw (x4)

(F) M5 x 15 Screw (x4)

(G) M5 Washer (x4)

FULL MOTION WALL MOUNT

FOR LCD, PLASMA, and LED DISPLAYS

UA-PRO110