Premier Mounts CTM-MS2 - Manual

CTM-MS2 Page - 8 - Installation Manual Thread Depth Indicator 1. Insert the thread depth indicator (supplied) through the thread inserts found on the back of the flat panel to make sure the inserts measure the same full depth and mark it (Figure 1). 2. Locate the correct diameter screw for the threa...

CTM-MS2 Installation Manual Page - 9 - Mounting Bracket Installation NOTE : Proper installation procedure by qualified personnel as outlined in the installation instructions must be adhered to. Failure to do so could result in serious personal injury and possible damage to the flat panel. WARNING : ...

CTM-MS2 Page - 10 - Installation Manual 3. Install the nylon spacers (if needed) to the mounting points on the flat panel (Figure 6). 4. Lay the left and right mounting brackets (stamped arrows facing out) - (Figure 7). Figure 6 Figure 7 5. Match the center of viewing guide with the centerline you m...

CTM-MS2 Installation Manual Page - 11 - L C Figure 8 Figure 9 7. The Griplates™ have M4, M5 M6 and M8 hole patterns to fit the hardware that your flat panel requires. EXAMPLE: If your plasma uses M8 x 20 Phillip screws. Use the M8 mounting points (Figure 10). 8. Once the mounting brackets are aligne...

CTM-MS2 Page - 12 - Installation Manual CTM-MS2 Installation 1. Using a (commercially available) wood stud finder, locate the 16" or 24" stud centers behind the wall (Figure 12). 2. Once found, make a pencil marking on the center of the wood studs (Figure 13). NOTE: The wall plates have 16&#...

CTM-MS2 Installation Manual Page - 13 - 4. Level the wall plate with the reference arrow pointing up to the ceiling (Figure 15). 5. Drill six (6) ¼" pilot holes to the marked wall. 6. Secure the plate using the six (6) 5/16" lag bolts and flat washers (Figure 16). 16" Figure 15 Figure 16...

CTM-MS2 Installation Manual Page - 15 - 2. Make any lateral shift adjustment and lock it by tightening the two (2) M6 x 30mm Phillips screws found on the bottom of the mounting brackets. Use the foot leveler to adjust your plasma. CAUTION : Do not over tighten the M6 x 30mm screws to the rods (Figur...

CTM-MS2 Installation Manual Page 17 Technical Specifications 28.000 (171.2) 1 2 L C 16.000(406.4) 24.000 (616.97) 8.000 (203.2) 8.000 (203.2) 19.000(482.6) CL 21.000 (533.4) 12° 2.331 (59.21) 19.000(482.6) A B C D E H G F G H A. Wall plate B. Mounting brackets C. Griplate™ D. Mounting hardware E. M6...

CTM-MS2 Page 18 Installation Manual Warranty Limited Lifetime Warranty All Premier Mounts products carry a limited lifetime warranty from ship date against defects in materials and workmanship. Premier Mounts is not liable for improper installation that results in damage to mounts, adapters, display...

CTM-MS2 Installation Manual Page 19 Notes Premier Mounts 3130 E. Miraloma Avenue Anaheim, CA 92806 Phone: (800) 368-9700 Fax: (800) 832-4888 [email protected] www.mounts.com IN-CTMMS2.R2

AST-2446/2 Suspension Adapter Installation Instructions Page 1 AST-2446/2 INSTALLATION INSTRUCTIONS 1. Separate the upper pipe and lower tube. Install the upper pipe to the ceiling structure using commercial standards and commercially available suitable hardware (Figure 1). 2. Once the upper pipe ha...

AST-2446/2 Suspension Adapter Page 2 Installation Instructions Figure 2 . Figure 3 .

PSD-S Installation Instructions Page 1 PSD-S INSTALLATION INSTRUCTIONS 1. Separate the upper pipe and the lower tube. 2. Install the upper pipe in the ceiling structure using suitable commercial hardware. 3. Screw the lower portion of the PSD-S to the coupling and secure with the Allen screws. 4. On...