PowerSmart PS4006 - User Manual

Page 3 - CONTENTS; Special safety rules for electric mini circular saw...........................; TECHNICAL DATA; Electric Mini Circular Saw

3 CONTENTS Technical data…...………………………………………………………. 3 Introduction …...………………………………………………………... 4 Safety information …...………………………………………………… 4 General safety rules…….……………………………………………….. 5 Special safety rules for electric mini circular saw……………………… 8 Symbols …...……………………………………………………….…… 11 Knowing ...

Page 4 - INTRODUCTION; Thank You for Purchasing a PowerSmart; SAFETY INFORMATION; DANGER

4 INTRODUCTION Thank You for Purchasing a PowerSmart ® Product. This manual provides information regarding the safe operation and maintenance of this product. Every effort has been made to ensure the accuracy of theinformation in this manual. PowerSmart ® reserves the right to change this product an...

Page 5 - GENERAL SAFETY RULES; SAVE THESE SAFETY INSTRUCTIONS; is, have a licensed electrician check the outlet.

5 GENERAL SAFETY RULES Safety is a combination of common sense, staying alert, and knowing how your power tool works. SAVE THESE SAFETY INSTRUCTIONS . WARNING: Do not operate this unit until you read this instruction manual for safety, operation and maintenance instructions. Failure to follow all in...

Page 8 - SPECIFIC SAFETY RULES FOR ELECTRIC MINI CIRCULAR SAW; When cutting pipe or conduit ensure that etc.

8 SPECIFIC SAFETY RULES FOR ELECTRIC MINI CIRCULAR SAW  Hold power tool by insulated gripping surfaces, when performing an operation where the cuttingaccessory may contact hidden wiring. Cutting accessory contacting a “live” wire may make exposedmetal parts of the power tool “live” and could give t...

Page 9 - Cutting Procedures; Keep hands away from the cutting area and the saw blade.

9 Cutting Procedures WARNING: Keep hands away from the cutting area and the saw blade.  Do not reach underneath the workpiece. The guard cannot protect you from the blade below theworkpiece.  Adjust the cutting depth to the thickness of the workpiece. Less than a full tooth of the blade teethshoul...

Page 10 - stare into the beam, please observe all safety rules as follows:

10 Lower Guard Function  Check lower guard for proper closing before each use. Do not operate the saw if lower guard does notmove freely and close instantly. Never clamp or tie the lower guard into the open position. If saw isaccidentally dropped, lower guard may be bent. Raise the lower guard with...

Page 11 - SYMBOLS

11 SYMBOLS Some of the following symbols may be used on this product. Please study them and learn their meaning.Proper interpretation of these symbols will allow you to operate the product better and safer. SYMBOL NAME DESIGNATION/EXPLANATION V Volts Voltage A Amperes Current Hz Hertz Frequency (cyc...

Page 12 - KNOWING YOUR ELECTRIC MINI CIRCULAR SAW; Unpacking; Saw blade

12 KNOWING YOUR ELECTRIC MINI CIRCULAR SAW Unpacking Unpack the power tool and all its parts, and compare against the list below. Do not discard the carton orany packaging materials. Please call 1-800-791-9458 or E-mail us at [email protected] if anyparts are damaged or missing. Including: Electric ...

Page 13 - ASSEMBLY INSTRUCTION; could result in serious personal injury.; MOUNTING/REPLACING THE SAW BLADE; Removal of the Saw Blade; Clean the saw blade (1) and all clamping parts to be assembled.

13 ASSEMBLY INSTRUCTION WARNING: Do not use this product if any parts on the packing list are already assembled to your productwhen you unpack it. Parts on this list are not assembled to the product by the manufacturerand require customer installation. Use of a product that may have been improperly ...

Page 14 - OPERATING INSTRUCTION; SWITCHING ON AND OFF; ADJUSTMENT; Depth adjustment

14 INSTALL THE RIP GUIDE To install the rip guide on the machine, perform the following steps.  Unplug your circular saw.  Insert the rip guide (7) through all three slots on the base plate (3) at the front of the saw, starting withslot in the left side edge of the base.  Slide the left guide (7)...

Page 15 - Angle Adjustment; CUTTING METHODS; Parallel Cut Adjustment

15 Angle Adjustment  Loosen the bevel scale bracket (10) for angle adjustment.  Adjust the base plate (3) to the desired angle between 0°to45°  Tighten the bevel scale bracket （ 10 ） . CUTTING METHODS Parallel Cut Adjustment  Loosen the lock knob of edge guide.  Slide the edge guide through the...

Page 16 - LASER FUNCTION; Press the laser generator switch to “I” position, the laser

16 LASER FUNCTION WARNING: Do not stare directly at the laser beam, do not deliberately aim the beam at personnel and ensure that it is not directed towards the eye of a person for longer than 0.25s. When you make the line of the cut on the work piece, the laser line generator can help you get bette...

Page 17 - MAINTENANCE; Blade

17 MAINTENANCE WARNING: Do not at any time let brake fluids, gasoline, petroleum-based products, penetrating oils, etc., come in contact with plastic parts. Chemicals can damage, weaken ordestroy plastic which may result in serious personal injury. Regular cleaning is required for the safe operation...

Page 18 - EXPLODED VIEW& PARTS LIST

PowerSmart PS4006 - User Manual

Table of Contents:

Summary