Powermatic 1791293 - User Manual

Page 2 - Warranty and Service

2 Warranty and Service Powermatic ® warrants every product it sells against manufacturers’ defects. If one of our tools needs service or repair, please contact Technical Service by calling 1-800-274-6846, 8AM to 5PM CST, Monday through Friday. Warranty Period The general warranty lasts for the time ...

Page 3 - Table of Contents

3 Table of Contents Warranty and Service .................................................................................................................................... 2 Table of Contents .............................................................................................................

Page 7 - Features of the OES9138 Edge Sander

7 Features of the OES9138 Edge Sander Read and understand the entire contents of this manual before attempting set-up or operation! Failure to comply may cause serious injury.

Page 8 - Unpacking; Contents of the Shipping Container; Assembly

8 Unpacking Open shipping container and check for shipping damage. Report any damage immediately to your distributor and shipping agent. Do not discard any shipping material until the Edge Sander is assembled and running properly. Compare the contents of your container with the following parts list ...

Page 9 - Control Switch Bracket; Grounding Instructions

9 7. The Edge Sander should be located in a dry, well-lighted area, on a solid and level surface, preferably a concrete floor. Leave plenty of space around the machine for operations and routine maintenance work. 8. Exposed metal areas of the Edge Sander have been factory coated with a protectant. T...

Page 11 - Test Run After Wiring; Converting to 460 Volt; Adjustments; Main Table Positioning

11 Test Run After Wiring On the three-phase unit, after wiring has been completed, you should check that the wires are connected properly: 1. Connect machine to power source and press the start button (A, Figure 8). 2. The sanding belt should move left to right, as viewed from the front of the machi...

Page 13 - Tracking Adjustment

13 End Guard The end guard (A, Figure 15) on the right side of the machine can be swung out of the way for sanding long workpieces. (The miter gauge will need to be removed for such a procedure.) Loosen the hand knob (B, Figure 15) and swing open the end guard all the way until it catches the latch ...

Page 14 - Operating Controls

14 To adjust tracking, proceed as follows: 1. Loosen the nut (A, Figure 18). 2. Turn the adjustment knob (B, Figure 18) counter-clockwise to shift the belt upward; clockwise to shift the belt downward. 3. When the belt is centered and tracking properly, tighten nut (A, Figure 18). 4. After adjustmen...

Page 15 - Maintenance; Lubrication

15 Maintenance Before doing maintenance on the machine, disconnect it from the electrical supply. Failure to comply may cause serious injury. Periodically check both drums. The drums are made of rubber material and may experience wear after a long period of use, at which time they should be replaced...

Page 16 - Troubleshooting the OES9138 Edge Sander

16 Troubleshooting the OES9138 Edge Sander Trouble Probable Cause Remedy Machine will not start/restart or repeatedly trips circuit breakers or blows fuses. Machine not connected to power source. Verify machine is connected to power. Fuse blown, or circuit breaker tripped. Replace fuse, or reset cir...

Page 19 - Replacement Parts

19 Replacement Parts Replacement parts are listed on the following pages. To order parts or reach our service department, call 1-800-274-6848 Monday through Friday, 8:00 a.m. to 5:00 p.m. CST. Having the Model Number and Serial Number of your machine available when you call will allow us to serve yo...

Page 20 - Parts List: Base Assembly

20 Parts List: Base Assembly Index No. Part No. Description Size Qty 1 ............... OES-001 .................. Machine Base ...................................................... .................................... 1 2 ............... OES-002 .................. Magnetic Motor Starter ..............

Page 21 - Base Assembly

Page 22 - Parts List: Drive Unit

22 Parts List: Drive Unit Index No. Part No. Description Size Qty 1 ............... OES-020 .................. Ball Bearing Assembly ...................................... ....................................... 2 2 ............... TS-2360121 ............. Flat Washer ..................................

Page 23 - Drive Unit

Page 24 - Parts List: Tracking and Belt Release Unit

24 Parts List: Tracking and Belt Release Unit Index No. Part No. Description Size Qty 1 ............... OES-036 .................. Belt Release Post ................................................ .................................... 2 2 ............... OES-037 .................. Bushing .............

Page 25 - Tracking and Belt Release Unit

25 Tracking and Belt Release Unit 1 2 3 1 33 3 0 1 2 3 2 2 0 21 2 6 6 2 6 22 1 8 6 25 3 5 3 7 3 6 34 14 6 1 6 17 1 8 8 1 8 1 9 1 1 7 6 5 9 1 0 12 1 3 3 3 9 3 6 38 4

Page 26 - Parts List: Table Assembly

26 Parts List: Table Assembly Index No. Part No. Description Size Qty 1 ............... OES-056 .................. Elevation Casting ................................................. .................................... 1 2 ............... OES-057 .................. DU Bushing .........................

Page 28 - Parts List: Contour Sanding Unit

28 Parts List: Contour Sanding Unit Index No. Part No. Description Size Qty 1 ............... OES-077A ................ Sanding Arm Casting ........................................... .................................... 1 2 ............... TS-1550071 ............. Flat Washer .........................

Page 30 - Electrical Connections – 1 Phase, 230V

Page 31 - Electrical Connections – 3 Phase, 230V

Page 32 - Electrical Connections – 3 Phase, 460V

Powermatic 1791293 - User Manual

Table of Contents:

Summary

Other Powermatic Grinding Machines Models