Powermatic 1632 - Manual - manualsarea.com

Page 2 - Warranty and Service

2 1.0 Warranty and Service Powermatic warrants every product it sells against manufacturers’ defects. If one of our tools needs service or repair, please contact Technical Service by calling 1-800-274-6846, 8AM to 5PM CST, Monday through Friday. Warranty Period The general warranty lasts for the t...

Page 3 - Table of contents

3 2.0 Table of contents Section Page 1.0 Warranty and Service ..................................................................................................................................... 2 2.0 Table of contents .....................

Page 4 - Safety warnings

4 3.0 Safety warnings As with all machines, there is a certain amount of hazard involved with the use of this sander. Use the machine with the respect and caution demanded where safety precautions are concerned. W hen normal safety precautions are overlooked or ignored, personal injury to the oper...

Page 5 - About this manual

5 blades. A machine under repair should be RED TAGGED to show it should not be used until the maintenance is complete. 14. Maintain tools in top condition. Keep all tools sharp and clean for the best and safest performance, and follow instructions for lubricating and changing accessories. Never st...

Page 6 - Specifications

6 5.0 Specifications Stock number ...................................................... 1791250 ..........................................................1791251 Model number ..................................................... 1632-1 ................................................................

Page 7 - Setup and assembly; Shipping contents; Electrical connections; Voltage conversion

7 6.0 Setup and assembly Remove the sander from its crate and inspect for damage to ensure all parts are intact. Any damage should be reported to your distributor and shipping agent immediately upon discovery. Before proceeding with installation, read your instruction manual thoroughly. Familiariz...

Page 8 - Adjustments

8 An undersized cord will cause a drop in line voltage resulting in loss of power and overheating. Table 1 shows correct size to use depending on cord length and nameplate ampere rating. If in doubt, use the next heavier gauge. The smaller the gauge number, the heavier the cord. 8.0 Adjustments Di...

Page 9 - Feed speed adjustment; Operation; Controls; Maintenance

9 Figure 5 8.5 Feed speed adjustment The Model 1632 has two speeds that feed the workpiece at 15 feet per minute (FPM) finished surface sanding, and 32.5 FPM for faster, lighter sanding. To change the feed rate: 1. Disconnect machine from power source. 2. Remove cap screw that holds the sprocket c...

Page 10 - Troubleshooting the 1632 Sander; Replacement Parts

10 11.0 Troubleshooting the 1632 Sander Symptom Possible Cause Correction Motor will not start Low voltage. Check power line for proper voltage. Open circuit in motor or loose connection. Inspect all lead connections on motor for loose or open connections. Motor will not start: fuses or circuit br...

Page 12 - Electrical Control and Upper Adjustment Roller – Exploded View

12 12.2.1 Electrical Control and Upper Adjustment Roller – Exploded View

Page 13 - Electrical Control and Upper Adjustment Roller – Parts List

13 12.2.2 Electrical Control and Upper Adjustment Roller – Parts List Index No Part No Description Size Qty 1 ................ 6293203 .................... Upper Door (L) ......................................................... ...................................... 1 2 ................ 6293204 ....

Page 14 - Sanding Drum Assembly – Exploded View

Page 15 - Sanding Drum Assembly – Parts List

15 12.3.2 Sanding Drum Assembly – Parts List Index No Part No Description Size Qty 1 ................ 6293240 .................... Ring ......................................................................... ...................................... 2 2 ................ 6293241 .......................

Page 17 - Base and Table Adjustment Assembly – Parts List

17 12.4.1 Base and Table Adjustment Assembly – Parts List

Page 20 - Conveyor Belt and Table – Exploded View

20 12.5.1 Conveyor Belt and Table – Exploded View

Page 21 - Reduction Motor – Exploded View

Page 22 - Conveyor Belt and Table Reduction Motor – Parts List

22 12.5.3 Conveyor Belt and Table; Reduction Motor – Parts List Index No Part No Description Size Qty 1 ................ 6293351 .................... Hex Socket Cap Screw ............................................ 1/4" x 1/4"...................... 6 2 ................ 6293352 ..............

Page 24 - Electrical Connections – 1632 Sander

24 13.0 Electrical Connections – 1632 Sander 13.1 460V – 3 Phase