Poulan PRO 810 EPT - Manual

Page 2 - IMPORTANT WARNINGS AND; PLAN AHEAD

2 IDENTIFICATION OF SYMBOLS DANGER! This unit can be dangerous! Careless or im- proper use can cause serious or even fatal injury. Read and understand the instruction manual before using the unit. DANGER! Falling objects can cause severe head injury. Wear head protection when operating this unit. Do...

Page 3 - DANGER; ELECTRICAL SAFETY

3 Snug Fitting Clothing Safety Shoes Safety Chaps Heavy Duty Gloves Eye Protection Hearing Protection Safety Hat S Keep children, bystanders, and animals a minimum of 50 feet (15 meters) away from the work area. Do not allow other people or animals to be near when starting or operat- ing the unit. D...

Page 4 - DOUBLE INSULATION CONSTRUCTION; PRUNER SAFETY

4 vent damage to unit and/or extension cord and to reduce the possibility of the extension cord disconnecting from the unit during op- eration. See ATTACH THE EXTENSION CORD TO YOUR TRIMMER in the OPERA- TION section. S Do not attempt to repair unit. Inspect the insu- lation and connectors on the po...

Page 7 - RECOMMENDED ATTACHMENTS; ADDITIONAL SAFETY RULES; FOR OPTIONAL ATTACHMENTS

7 of this tool and seek medical attention. An anti--vibration system does not guarantee the avoidance of these problems. Users who op- erate power tools on a continual and regular basis must monitor closely their physical con- dition and the condition of this tool. RECOMMENDED ATTACHMENTS This model...

Page 8 - EDGER SAFETY; SAVE THESE INSTRUCTIONS; VACUUM SAFETY

8 EDGER SAFETY WARNING: Always use handlebar when operating edger attachment. Attach handlebar above arrow on safety label on the upper shaft (motor end of unit). If your edger attachment does not include a handlebar, a handlebar accessory kit (#530071864) is available from your authorized service d...

Page 10 - ASSEMBLY

10 ASSEMBLY WARNING: If received assembled, review all assembly steps to ensure your unit is properly assembled and all fasteners are secure. Examine parts for damage. Do not use dam- aged parts. NOTE: If you need assistance or find parts missing or damaged, call 1-800-554-6723. TOOLS REQUIRED S Hex...

Page 11 - PIVOT; OPERATION; OPERATING INSTRUCTIONS; SELECT AN EXTENSION CORD

11 ATTACHING SHIELD (for line trimmer attachment) WARNING: The shield must be prop- erly installed. The shield provides partial protec- tion from the risk of thrown objects to the opera- tor and others and is equipped with a line limiter blade which cuts excess line to the proper length. The line li...

Page 15 - MAINTENANCE

15 Mowing SWEEPING -- The fanning action of the rotat- ing line can be used for a quick and easy clean up. Keep the line parallel to and above the surfaces being swept and move the tool from side to side. Sweeping MAINTENANCE WARNING: Disconnect unit from power source before performing maintenance. ...

Page 16 - SERVICE AND ADJUSTMENTS; CHAIN SHARPENING

16 BAR MAINTENANCE If your pruner cuts to one side, has to be forced through the cut, or been run with an im- proper amount of bar lubrication it may be necessary to service your bar. A worn bar will damage your chain and make cutting difficult. After each use, with unit disconnected from power sour...

Page 17 - USER REPLACEABLE SERVICE PARTS; STORAGE; SEASONAL STORAGE

17 12. Now, install bar clamp making sure the adjusting pin is positioned in the lower hole in the guide bar. Adjusting Pin Lower Hole Guide Bar 13. Install bar clamp nut and finger tighten only. Do not tighten any further at this point. Proceed to the CHAIN ADJUST- MENT section. CHAIN ADJUSTMENT Se...

Page 19 - LIMITED WARRANTY

19 TROUBLE CAUSE REMEDY Line pulls back into head. 1. Too little line outside of head. 2. Line size incorrect. 1. Remove cover and pull 4 inches (10 cm) of line outside of head. 2. Use only 0.080 inch (2 mm) dia. line. TROUBLESHOOTING TABLE (continued) Line usage is excessive. 1. Check line routing....

Poulan PRO 810 EPT - Manual

Table of Contents:

Summary

Other Poulan PRO Models