Porter-Cable RN175 - Manual

Page 2 - GB; ENGLISH

2 Matthew G. PopikVice President of Engineering PORTER ✦✦ CABLE Porter-Cable Corporation4825 Highway 45 NorthJackson, TN 38305 Date of Manufacture: ___________________________ Fecha de fabricación:, Date de fabrication: Serial No: ______________________________________ Número de serie:, Nombre d'ord...

Page 3 - GENERAL SAFETY RULES; When using pneumatic tools, basic safety precautions; DEATH; or; SERIOUS INJURY; Check manual for selectable; Never use oxygen or other bottled; Explosion may occur. Never use

3 GENERAL SAFETY RULES DANGER: When using pneumatic tools, basic safety precautions should always be followed to reduce the risk of personal injury, includingthe following: READ AND FOLLOW ALL INSTRUCTIONS. There are certain applications for which this tool was designed. Porter-Cablestrongly recomme...

Page 5 - Keep proper footing; Fire fasteners into work surface only:; In

5 22. Do not overreach. Keep proper footing a n d b a l a n c e a t a l l t i m e s w h e n u s i n g o rhandling the tool. 23. Fire fasteners into work surface only: never into materials too hard to penetrate.Fig. 15. 24. Grip tool firmly to maintain controlwhile allowing tool to recoil away fromwo...

Page 6 - FOREWORD

6 EMPLOYER’S RESPONSIBILITIES DANGER: Employer must enforce compliance with the safety warnings and all other instructions contained in this manual. Keep this manual available for use by all people assigned to use this tool. For personal safety and proper operation of this tool, read and understandt...

Page 7 - PREPARING THE TOOL

7 Fig. 19 PREPARING THE TOOL 1. After reading and understanding this entire manual, connect tool to air supply (Fig. 18). DANGER: Never point tool at yourself or others in work area. Always connect tool to air supply before loading fasteners (Fig. 18). Do not load fasteners with trigger or safety de...

Page 8 - sliding off the roof.

8 6. Close magazine cover, close and latch feeder cover (see Fig. 23). 7. Adjust directional exhaust deflector (A) Fig. 24, so that the exhaust airblast will be directed away from the operator. The exhaust deflector providesseven detented positions for directing the exhaust blast away from theoperat...

Page 9 - OPERATING INSTRUCTIONS; USING THE TOOL WITH SELECTABLE TRIGGERING OPTIONS; ” trigger, which will; limit; the; single sequential actuation

9 OPERATING INSTRUCTIONS USING THE TOOL WITH SELECTABLE TRIGGERING OPTIONS Complete all steps of PREPARING THE TOOL before using the tool. This tool is shipped from the factory with a selectable trigger set in the “SINGLE SEQUENTIAL ACTUATION” firing mode as described in number 1 below. The selectab...

Page 10 - Do Not; CLEARING A JAMMED FASTENER

10 D A N G E R : K e e p f i n g e r s A W A Y f r o m t r i g g e r w h e n n o t d r i v i n g fasteners to avoid accidental firing. Never carry tool with finger ontrigger: tool will fire a fastener if safety is bumped. Never point tool at yourself or others in work area. Never attempt to drive a ...

Page 11 - MAINTENANCE; CLEAN AND INSPECT DAILY; Disconnect tool from air supply before cleaning and; SERVICE AND REPAIRS; TROUBLESHOOTING; Disconnect tool from air supply before performing

11 MAINTENANCE CLEAN AND INSPECT DAILY WARNING: Disconnect tool from air supply before cleaning and inspection. Correct all problems before placing the tool back in use. Wipe tool clean and inspect for wear or damage. Use non-flammablecleaning solutions to wipe exterior of tool only if necessary. DO...

Page 12 - ACCESSORIES; for a catalog or for the name of your nearest supplier.

12 PORTER-CABLE LIMITED ONE YEAR WARRANTY Porter-Cable warrants its nailing and stapling tools for a period of one year from the date of originalpurchase. We will repair or replace at our option, any part or parts of the product and accessoriescovered under this warranty which, after examination, pr...

Porter-Cable RN175 - Manual

Table of Contents:

Summary

Other Porter-Cable Models