Porter-Cable MS200 - Manual

Page 2 - GB; ENGLISH

2 Matthew G. PopikVice President of Engineering PORTER ✦✦ CABLE Porter-Cable Corporation4825 Highway 45 NorthJackson, TN 38305 Date of Manufacture:___________________________ Fecha de fabricación:, Date de fabrication: Serial No:______________________________________ Número de serie:, Nombre d'ordre...

Page 3 - SAFETY GUIDELINES / DEFINITIONS; SAVE THESE INSTRUCTIONS!; IMPORTANT SAFETY INSTRUCTIONS; READ AND FOLLOW ALL INSTRUCTIONS.

3 indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury. indicates a potentially hazardous situation which, if not avoided, could result in death or serious injury. indicates a potentially hazardous situation which, if not avoided, may result in mi...

Page 4 - GENERAL SAFETY RULES

4 Fig. 6 Fig. 5 Fig. 2 Fig. 3 Fig. 4 1. Read and understand tool labels andmanual. Failure to follow warnings couldresult in DEATH or SERIOUS INJURY. Fig. 1. 2. Operator and others in work area MUSTwear safety glasses with side shields.These safety glasses must conform to ANSIZ87.1 requirements (app...

Page 5 - Do not connect tool to pressure which

5 9. Do not connect tool to pressure which potentially exceeds 200 PSI (13.7 BAR).10. Only use air hose that is rated for amaximum working pressure of at least 150PSI (10.3 BAR) or 150% of the maximumsystem pressure, which ever is greater.11. Connect tool to air supply hose with acoupling that autom...

Page 6 - TECHNICAL SPECIFICATIONS

6 21. Remove finger from trigger when notdriving fasteners. Never carry tool with fingeron trigger. In “Contact Actuation Mode” toolwill fire a fastener if safety is bumped whiletrigger is depressed. Fig. 14. 22. Do not overreach. Keep proper footinga n d b a l a n c e a t a l l t i m e s w h e n u ...

Page 7 - EMPLOYER’S RESPONSIBILITIES

7 Employer must enforce compliance with the safety warnings and all other instructions contained in this manual. Keep this manual available for use by all people assigned to use this tool. For personal safety and proper operation of this tool, read and understandtool labels and manual. Failure to fo...

Page 9 - USING THE TOOL WITH SELECTABLE TRIGGERING OPTIONS; To use the tool in the SINGLE SEQUENTIAL ACTUATION MODE; OPERATING INSTRUCTIONS

9 USING THE TOOL WITH SELECTABLE TRIGGERING OPTIONS Complete all steps of PREPARING THE TOOL before using the tool. This tool is shipped from the factory with a selectable trigger set in the“SINGLE SEQUENTIAL ACTUATION” firing mode as described in number1 below. The selectable trigger can be set for...

Page 10 - CLEARING A JAMMED FASTENER

10 Keep fingers AWAY from trigger when not driving fasteners to avoid accidental firing. Never carry tool with finger on trigger. In “Contact Actuation Mode” tool will fire a fastener if safety is bumped while trigger is depressed. Never point tool at yourself or others. Never attempt to drive a fas...

Page 11 - CLEAN AND INSPECT DAILY; SERVICE AND REPAIRS; MAINTENANCE

11 CLEAN AND INSPECT DAILY D i s c o n n e c t t o o l f r o m a i r s u p p l y b e f o r e c l e a n i n g a n d inspection. Correct all problems before placing the tool back in use. Wipe tool clean and inspect for wear or damage. Use non-flammablecleaning solutions to wipe exterior of tool only i...

Page 12 - ACCESSORIES

12 2. Tool does nothing or Inadequate air supply. Verify adequate air supply. operates sluggishly. Inadequate lubrication. Put 5 or 6 drops of oil into air inlet. Worn or damaged Install Overhaul Kit. o-rings or seals. 3. Air leak near bottom Loose screws. Tighten screws. of tool. Worn or damaged In...

Porter-Cable MS200 - Manual

Table of Contents:

Summary

Other Porter-Cable Models