Porter-Cable MODEL 7310 - Manual

Page 3 - SAFETY GUIDELINES - DEFINITIONS; CALIFORNIA PROPOSITION 65

Some dust created by power sanding, sawing, grinding, drilling, and other construction activities contains chemicals known (to the State of California) to cause cancer, birth defects or other reproductive harm. Some examples of these chemicals are: ● lead from lead-based paints ● crystalline silica ...

Page 4 - GENERAL SAFETY RULES

R e a d a l l i n s t r u c t i o n s . F a i l u r e t o f o l l o w a l l instructions listed below may result in electric shock, fire and/or serious injury. The term "power tool" in all of the warnings listed below refers to your mains-operated (corded) power tool or battery-operated (cor...

Page 6 - ADDITIONAL SPECIFIC SAFETY RULES; causing personal injury or damage to work.

6 ADDITIONAL SPECIFIC SAFETY RULES 1. HOLD POWER TOOLS BY INSULATED GRIPPING SURFACES WHENPERFORMING AN OPERATION WHERE THE CUTTING TOOL MAYCONTACT HIDDEN WIRING OR ITS OWN CORD. Contact with a "live" wire will make exposed metal parts of the tool "live" and shock the operator. 2. U ...

Page 7 - NOTES

Page 8 - IPXX

8 SAVE THESE INSTRUCTIONS! SYMBOL DEFINITION V ........................ volts A ........................ amperes Hz ........................ hertz W ........................ watts kW ........................ kilowatts F ........................ farads µ F ........................ microfarads l ........

Page 9 - EXTENSION CORD SELECTION

9 If an extension cord is used, make sure the conductor size is large enough toprevent excessive voltage drop which will cause loss of power and possiblemotor damage. A table of recommended extension cord sizes will be found inthis section. This table is based on limiting line voltage drop to 5 volt...

Page 10 - FUNCTIONAL DESCRIPTION; FOREWORD; These trimmers are equipped with a; CARTON CONTENTS; TO START AND STOP MOTOR

10 FUNCTIONAL DESCRIPTION FOREWORD Porter-Cable Laminate Trimmers are designed for flush and bevel trimminglaminated plastics, phenolics, and other similar materials having a bondingagent too hard to be trimmed with ordinary tools. The Tilt-Base model allows trimming into corners inaccessible to sta...

Page 11 - MODEL 7310 TRIMMER ASSEMBLY

11 TO AVOID PERSONAL INJURY OR DAMAGE TO FINISHEDW O R K A L W A Y S A L L O W T H E M O T O R T O C O M E T O ACOMPLETE STOP BEFORE SETTING TRIMMER DOWN. TO INSTALL BIT DISCONNECT TOOL FROM POWER SOURCE. 1. On Models 7310 and 7319 bits may be installed with the motor unit either assembled or remove...

Page 13 - ASSEMBLING AND ADJUSTING BASE AND ROLLER GUIDE; Guide mounting holes are oversized allowing guide to be; For making flush cuts; align roller guide with straight portion of bit.; For; Tighten all screws and make a trial cut on scrap material to check; FLUSH TRIMMING; DISCONNECT TOOL FROM POWER SOURCE.; Attach base and guide to trimmer as outlined under ASSEMBLING AND

13 ASSEMBLING AND ADJUSTING BASE AND ROLLER GUIDE 1. Remove power unit from base unit (see “TO INSTALL BIT”), and install the bit. 2. The base and roller guide (A) Fig. 4, is assembled at the factory. Toassemble, remove a sub-base mounting screw (A) Fig. 5 and insert alignment pinin guide base into ...

Page 14 - Make a trial cut on scrap material. Readjust if necessary.; BEVEL TRIMMING; Make a trial cut on scrap material to check alignment. Readjust if; USING STRAIGHT EDGE GUIDE; MODEL 7319 TILT BASE TRIMMER ASSEMBLY; ADJUSTING DEPTH OF CUT

14 5. Remove guide setting gauge from trimmer and install flush trimming bit. 6. Adjust depth of cut so that the straight portion of the bit extends below the trimmer base at least the thickness of the material to be trimmed.7. Make a trial cut on scrap material. Readjust if necessary. BEVEL TRIMMIN...

Page 15 - ADJUSTING TILT; MODEL 7312 OFFSET TRIMMER ASSEMBLY; ASSEMBLING OFFSET BASE TO MOTOR

15 be sure at least 1 / 2 " of bit shank is engaged in collet. Do not use bits that result in having less than 1 / 2 " of bit shank engaged in collet. To do so may cause poor gripping of collet resulting in loose bit anddamage to work, or personal injury should the bit come out of collet. AD...

Page 18 - UNDERSCRIBE 7320 TRIMMER ASSEMBLY; The 43109 Trim Bit must be installed into the Trimmer Motor before; TYPICAL APPLICATIONS

18 UNDERSCRIBE 7320 TRIMMER ASSEMBLY The Underscribe Trimmer Base is assembled to the Model 7301 TrimmerMotor as follows: NOTE: The 43109 Trim Bit must be installed into the Trimmer Motor before attaching the motor to the Underscribe Base. DISCONNECT TOOL FROM POWER SOURCE. 1. Clean and insert shank...

Page 21 - TROUBLESHOOTING GUIDE; For assistance with your tool, visit our website at

21 5. Position the underscribe trimmer onto the face frame so that the top (see Fig. 19), is against the edge of the stile. NOTE: The trimmer should be to the right of the rail, so that the cutting action will move from right to left (see Fig. 19). 6. Verify that bit is clear of foreign objects and ...

Page 22 - KEEP TOOL CLEAN; Wear ANSI Z87.1 safety glasses while using compressed air.; FAILURE TO START; DELTA FACTORY; MAINTENANCE

22 KEEP TOOL CLEAN Periodically blow out all air passages with dry compressed air. All plastic partsshould be cleaned with a soft damp cloth. NEVER use solvents to clean plasticparts. They could possibly dissolve or otherwise damage the material. Wear ANSI Z87.1 safety glasses while using compressed...

Page 23 - SERVICE; REPLACEMENT PARTS; ACCESSORIES

23 SERVICE REPLACEMENT PARTS When servicing use only identical replacement parts. SERVICE AND REPAIRS All quality tools will eventually require servicing or replacement of parts due towear from normal use. These operations, including brush inspection andreplacement, should ONLY be performed by eithe...

Porter-Cable MODEL 7310 - Manual

Table of Contents:

Summary

Other Porter-Cable Models