Porter-Cable 7414 - Manual - manualsarea.com

Page 2 - GENERAL SAFETY RULES; WORK AREA

2 GENERAL SAFETY RULES WARNING! READ AND UNDERSTAND ALL INSTRUCTIONS. Failure to follow all instructions listed below, may result in electric shock, fire and/orserious personal injury. WARNING: SOME DUST CREATED BY POWER SANDING, SAWING,G R I N D I N G , D R I L L I N G , A N D O T H E R C O N S T R...

Page 4 - SPECIFIC SAFETY RULES AND SYMBOLS

4 unauthorized parts or failure to follow Maintenance Instructions may create arisk of electric shock or injury. SPECIFIC SAFETY RULES AND SYMBOLS 1. Always use proper guard with grinding wheel. A guard protects operator from broken wheel fragments. 2. Accessories must be rated for at least the spee...

Page 5 - ADDITIONAL SAFETY RULES FOR PAINT REMOVAL

3 N .......................... three-phase alternating current with neutral .......................... direct current n 0 .......................... no load .......................... alternating or direct current .......................... Class II Construction .......................... splash-pro...

Page 6 - CLEAN UP ALL REMOVED PAINT; AT THE END OF EACH WORK SESSION; REMOVE PROTECTIVE CLOTHING; MOTOR; EXTENSION CORD SELECTION; FUNCTIONAL DESCRIPTION; FOREWORD

6 8. CLEAN UP ALL REMOVED PAINT and dust by wet mopping the floors. Use a wet cloth to clean all walls, sills and any other surfaces where paint ordust is clinging. DO NOT SWEEP, DRY DUST OR VACUUM. Use a highphosphate detergent or trisodium (TSP) to wash and mop areas. 9. AT THE END OF EACH WORK SE...

Page 7 - TO START AND STOP THE MACHINE; ASSEMBLY

grinding operations when used with appropriate recommended accessories.T h e M o d e l 7 4 1 4 c a n b e u s e d a s a g r i n d e r w h e n e q u i p p e d w i t h t h eappropriate 7" or 9" Type 27 guard and grinding wheel (see ACCESSORIESsection of manual). Typical applications are smoothi...

Page 8 - TO INSTALL SANDING DISC

8 INSTALLATION: 1. Insert threaded end of handle into handle clamp (A) Fig. 1A. 2. Turn handle clockwise and tighten securely. CHANGING POSITIONS: 1. Loosen handle by turning 2 full turns counterclockwise. 2. Push in on handle and move handle to desired location.3. Release handle. 4. Retighten secur...

Page 9 - TO INSTALL GRINDING WHEEL; OPERATION; REAR HANDLE LOCATION

9 W A R N I N G : A l w a y s m a k e s u r e t h e w h e e l g u a r d i s p o s i t i o n e d between operator and the wheel, so that flying chips or pieces of awheel that might break will be deflected away from the operator (seeFig. 3). TO INSTALL GRINDING WHEEL 1. CAUTION: DISCONNECT MACHINE FRO...

Page 11 - MAINTENANCE; KEEP TOOL CLEAN; FAILURE TO START

the front gear housing indicates the direction in which the grinding wheelrotates. MAINTENANCE KEEP TOOL CLEAN Periodically blow out all air passages with dry compressed air. All plasticparts should be cleaned with a soft damp cloth. NEVER use solvents to cleanplastic parts. They could possibly diss...

Page 12 - PORTER-CABLE LIMITED ONE YEAR WARRANTY; ACCESSORIES

12 PORTER-CABLE LIMITED ONE YEAR WARRANTY Porter-Cable warrants its Professional Power Tools for a period of one year from the date of originalpurchase. We will repair or replace at our option, any part or parts of the product and accessoriescovered under this warranty which, after examination, prov...

Page 13 - PORTER-CABLE SERVICE CENTERS; DELTA SERVICE CENTERS

The following are trademarks of PORTER-CABLE Corporation (Las siguientes son marcas registradas de PORTER-CABLE S.A.) (Les marquessuivantes sont des marques de fabriquant de la PORTER-CABLE Corporation): BAMMER ® , LASERLOC ® , OMNIJIG ® , POCKET CUTTER ® , PORTA-BAND ® , PORTA-PLANE ® , PORTER-CABL...

Porter-Cable 7414 - Manual

Table of Contents:

Summary

Other Porter-Cable Models