Porter-Cable 310 - Manual - manualsarea.com

Page 3 - CALIFORNIA PROPOSITION 65; SAFETY GUIDELINES - DEFINITIONS

3 Some dust created by power sanding, sawing, grinding, drilling, and other construction activities contains chemicals known (to the State of California) to cause cancer, birth defects or other reproductive harm. Some examples of these chemicals are: ● lead from lead-based paints ● crystalline silic...

Page 4 - GENERAL SAFETY RULES

4 R e a d a l l i n s t r u c t i o n s . F a i l u r e t o f o l l o w a l l instructions listed below may result in electric shock, fire and/or serious injury. The term "power tool" in all of the warnings listed below refers to your mains-operated (corded) power tool or battery-operated (c...

Page 6 - ADDITIONAL SPECIFIC SAFETY RULES; SAVE THESE INSTRUCTIONS!

6 1. U s e c l a m p s o r o t h e r p r a c t i c a l w a y t o s e c u r e a n d s u p p o r t t h eworkpiece to a stable platform. Holding the work by hand or against your body is unstable and may lead to loss of control. 2. Tighten Collet nut securely to prevent the bit from slipping. Nevertight...

Page 7 - IPXX

7 SYMBOL DEFINITION V ........................ volts A ........................ amperes Hz ........................ hertz W ........................ watts kW ........................ kilowatts F ........................ farads µ F ........................ microfarads l ........................ litre...

Page 8 - EXTENSION CORD SELECTION; MOTOR

8 EXTENSION CORD SELECTION If an extension cord is used, make sure the conductor size is large enough toprevent excessive voltage drop which will cause loss of power and possiblemotor damage. A table of recommended extension cord sizes will be found inthis section. This table is based on limiting li...

Page 9 - SELECTING THE BIT; FUNCTIONAL DESCRIPTION; FOREWORD

9 SELECTING THE BIT The Model 310 is equipped with a 1 / 4 " diameter collet to accept laminate trimming bits with 1 / 4 " diameter shanks. A – Motor Unit G – Ring Spring B – Base Unit H – Clamp Knob C – Sub-Base J – Collet Nut F – Depth Adjusting Ring K – Switch A F G H C B K J H C Fig. 1 F...

Page 10 - TO INSTALL BIT; TO REMOVE THE BIT; NEVER TOUCH BIT IMMEDIATELY AFTER USE, AS IT; ADJUSTING BIT EXPOSURE; DISCONNECT TOOL FROM POWER SOURCE.

10 TO INSTALL BIT 1. DISCONNECT TOOL FROM POWER SOURCE. 2. Remove power unit from base unit as follows:a. Loosen clamping knob (H) Fig. 1.b. Grasp power unit (A) Fig. 1, and pull straight up and out of the base unit (B) Fig. 1. This will also release the depth adjusting ring (F) Fig. 1,from ring spr...

Page 11 - USING A LAMINATE TRIMMER; Always wear ansi Z87.1 safety glasses while operating

11 USING A LAMINATE TRIMMER 1. Material to be trimmed must overhang the base material by a least 1 / 8 ". 2. Always wear ansi Z87.1 safety glasses while operating a laminate trimmer. 3. DISCONNECT TOOL FROM POWER SOURCE. 4. Firmly grasp motor housing being sure switch is in the “OFF” position. 5...

Page 12 - ASSEMBLING AND ADJUSTING BASE AND ROLLER (73100); Remove power unit from base unit (see TO INSTALL BIT), and install the

12 ASSEMBLING AND ADJUSTING BASE AND ROLLER (73100) 1. DISCONNECT TOOL FROM POWER SOURCE. 2. Remove power unit from base unit (see TO INSTALL BIT), and install the bit. 3. Position the base and roller guide assembly (A) Fig. 2, to the base unit. The alignment pin on the back of the guide base fits i...

Page 13 - FLUSH TRIMMING; Attach base and guide to trimmer as outlined under ASSEMBLING AND; BEVEL TRIMMING; Make a trial cut on scrap material to check alignment. Readjust if; USING STRAIGHT EDGE GUIDE; TROUBLESHOOTING

13 FLUSH TRIMMING 1. DISCONNECT TOOL FROM POWER SOURCE. 2. Attach base and guide to trimmer as outlined under ASSEMBLING AND ADJUSTING BASE AND ROLLER. 3. Remove roller guide and replace with flush trimming guide (B) Fig. 2. This guide may be identified by the molded on letter “F”. The stud on the e...

Page 14 - KEEP TOOL CLEAN; Wear ANSI Z87.1 safety glasses while using compressed air.; FAILURE TO START; MAINTENANCE

14 KEEP TOOL CLEAN Periodically blow out all air passages with dry compressed air. All plastic partsshould be cleaned with a soft damp cloth. NEVER use solvents to clean plasticparts. They could possibly dissolve or otherwise damage the material. Wear ANSI Z87.1 safety glasses while using compressed...

Page 15 - ACCESSORIES; REPLACEMENT PARTS; SERVICE

15 A complete line of accessories is available from your Porter-Cable • Delta Supplier, Porter-Cable • Delta Factory Service Centers, and Porter-Cable Authorized Service Stations. Please visit our Web Site www.porter-cable.com for a catalog or for the name of your nearest supplier. Since accessories...

Porter-Cable 310 - Manual

Table of Contents:

Summary

Other Porter-Cable Models