Philips SWW1810 Manual — Free PDF Download

Page 3 - Contents

3 English Contents 1 Important 4 Safety 4 2 Your Wireless HD AV Connect 6 What is in the box 6 3 Overview 7 The transmitter 7 The receiver 7 The remote control 8 4 Installation 9 Connect the transmitter to your HD devices 9 Connect the receiver to the HDTV set 9 Connect the IR blaster and IR sensor ...

Page 4 - Important; Safety; Important Safety Instructions

4 e Do not use this apparatus near water. f Clean only with dr y cloth. g Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions. h Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) tha...

Page 6 - Your Wireless; What is in the box

6 HDMI cable IR blaster extender cable Power adapter for the transmitter and receiver x 2 IR sensor extender cable Anchors x 2 Screws x 2 Quick Installation Guide Adhesive tape x 2 Quick star t guide User manual 2 Your Wireless HD AV Connect Congratulations on your purchase and welcome to Philips! T...

Page 7 - The receiver; Top view; Overview; The transmitter; Front view

7 English The receiver Top view 1 Source LEDs Indicators for HDMI1 and HDMI2 2 Power button with the LED indicator Press to turn the receiver on/off. 3 Source button Press to select the source input. Rear view 1 DC IN jack Connect the power adapter of the receiver. 2 HDMI OUT adapter Connect the HDT...

Page 8 - The remote control

8 The remote control 1 POWER button Press to turn the transmitter and receiver on/off. 2 INFO button Displays on the HDTV the connection status of the receiver. 3 IR button Press to switch the IR blaster frequency to meet the requirement of the source device. 4 SOURCE button Press to switch the audi...

Page 9 - Connect the receiver to the; Installation; Connect the transmitter to

9 English 2 Connect the supplied power adapter to the transmitter. • Connect one end of the power adapter to the DC IN jack of the transmitter. • Connect the other end of the power adapter to a power outlet. » The power button of the transmitter is lit in solid blue and turns red in standby mode. Co...

Page 10 - Install remote control; Connect the IR blaster and IR

10 5 Extend and stick the IR sensor extender cable onto the front side of your HDTV. Note • The IR blaster suppor t 47KHz remote signal protocol, while the IR sensor suppor ts 36KHz - 56KHz (NEC, RC5, RC6) remote signal protocol. Install remote control batteries Caution • Risk of explosion! Keep bat...

Page 11 - On screen display on HDTV; Activate your; Turn on the power of your

11 English On screen display on HDTV On screen display Mode and status Standby mode: it is a power- saving mode ..... Star t up in progress: It takes 15- 20 seconds. x and .... Searching available channels: It occurs when the link cannot establish over 80 seconds after initialization. HDMI CH1 On mo...

Page 12 - Activate the wireless link

12 Select the source on the transmitter Press the source buttons on the remote control, transmitter or receiver until you see the available video from your device. Tip • For information on the LED indicator status, see the section on ‘LED indicator status of the transmitter’. LED indicator status of...

Page 13 - Mount your; Mount your receiver on the

13 English 5 Hook the key holes at the back of the receiver on the screws. 6 Mount your receiver You can either mount the receiver on the wall or on the back of the HDTV. Mount your receiver on the wall 1 Select a spot near the HDTV. 2 Drill two holes in the wall. Make sure that the distance between...

Page 15 - Transmitter interfaces; Technical data; Supported resolution; General specification

15 English Power supply: Input: AC 100~ 240V Output: DC 5V, 2A Operating temperature: 0~40°C/32~104°F Transmitter interfaces A/V interfaces HDMI input: Two (Type A) Control signal interfaces IR blaster extender : 2.5mm jack Power interface Power input: 5V DC jack Switches Top power switch: One Top s...

Page 16 - Notice for Canada; Notice; Notice for USA

16 IMPORTANT NOTE: Radiation Exposure Statement: • This equipment complies with FCC radiation exposure limits set for th for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body. • This transmitter must not be co...

Page 17 - One Year Limited Warranty

17 English negative consequences on the environment and human health. Please visit www.recycle.philips.com for additional information on a recycling center in your area. HDMI, and HDMI logo, and High-Definition Multimedia Interface are trademarks or registered trademarks of HDMI licensing LLC in the...

Page 18 - Frequently asked question

18 9 Frequently asked question The power LED on the receiver is not lit up in red in standby mode. • Make sure that there is power supply for the transmitter and receiver. The computer screen image is not full screen on my TV. 1 Right-click on an open space on your desktop. 2 Select Graphics Options...