Philips AEH2900/37 - User Manual

5 EN Care of the environment Environmental information All unnecessar y packaging has been omitted. We have tried to make the packaging easy to separate into three materials: cardboard (box), polystyrene foam (buffer) and polyethylene (bags, protective foam sheet.) Your system consists of materials ...

6 EN • The sensors and/or Intelligent switch are intended as an aid. They are not substitutes for home security super vision and should not be used as such. Written Offer Gibson Innovations hereby offers to deliver, upon request, a copy of the complete corresponding source code for the copyrighted o...

7 EN 2 Overview With the Smar t Home devices and Philips Smart Home app, you can have the changes at your home monitored, and set rules to have the connected home appliance powered on or off automatically according to the changes. Motion sensor The Motion sensor detects the movement of people at hom...

8 EN a Status indicator b Alignment mark Temperature and humidity sensor The Temperature and humidity sensor detects the temperature and humidity at home. a Status indicator ab AEH2120 a AEH2130

11 EN 3 Setup Join your Smart Home network 1 On your mobile device, download and install the Philips Smart Home app. 2 Follow the onscreen instructions to get connected to the Bridge. 3 Follow the onscreen instructions to add your Smar t Home devices to the Bridge. For setup, bring the Smar t Home d...

12 EN Note • The device exits the pairing mode after three minutes. To re-enter the pairing mode, open the batter y door and close it as described in Step 3. Install or replace batteries To install or replace batteries on your Smar t Home devices, do the following: 1 2 Search All devices No device h...

14 EN Plug the Intelligent switch To add the Intelligent switch to the Bridge, do the following: 1 Inser t the Intelligent switch into a power outlet properly. 2 Press and hold the Setup button until the status indicator turns from amber to red.

15 EN Reset Reset network connection Reset the network connection when: • a device re-joins the Smar t Home network after the batteries are replaced. • there are connection problems with the Smar t Home network. Indicator Status of the device flashing red Network connection lost On the sensor , do t...

16 EN 2 With the Philips Smart Home app, add the device to the Bridge (see 'Join your Smar t Home network' on page 11 ). Restore factory settings Restore factor y settings when: • you want to connect your device to another Bridge. On the sensor , do the following: 1 Delete the device from the Bridge...

18 EN 4 Place • Use the Smar t Home devices in an indoor environment. • Keep such devices from exposure to moisture, direct sunlight, or excessive heat. • To ensure good connection, check the distance and obstacles, such as walls, between the Bridge and devices. Place the Motion sensor Find a right ...

19 EN • In Step 2, use the screw holder for a concrete wall or surface. For a wooden surface, you can the screw only. Use the adhesive tape You can also use the adhesive tape mount the sensor as needed. 1 3 4 a b 2 5mm >30mm

20 EN Place the Door and window sensor • Avoid the exposure to moisture and direct sunlight. • Use the alignment marks to align the two components. • Mount the two components securely just in case any one of them may drop during movement. 2 1 3

23 EN 5 Use Philips Smart Home app Through the Philips Smart Home app you can set up the Smar t Home devices, set rules of home automation, and continue to monitor changes and control the devices on a mobile device while you are away from home. a Go to the Home screen. b Find connected devices by ty...

24 EN Manage devices Set the device You can edit the device information by attaching a photo and naming the location. • On the Home screen, tap the device to edit the device information. • For the Motion sensor, select the sensitivity level as needed. • You can select the unit of measurement for the...

25 EN Delete the device Delete the device when: • you want to remove the device from the Bridge. • you want to restore the factor y settings of the device. (see 'Restore factor y settings' on page 16) 1 From the Home Screen, select the device. 2 Tap the option to delete the device.

26 EN Set the rules of home automation To set a rule of home automation, set an event or time/ location as trigger. Then, set an action that is associated with the trigger. Set the trigger 1 From the Home screen, go to . Tap to create a rule. 2 Tap a icon to set a trigger. • A trigger can be an even...

27 EN Edit the rules • From the Home screen, tap . Select a rule to edit or delete it.

28 EN Access the devices remotely To access your Smar t Home devices remotely, log in to the por tal. The first time you log in to the por tal, create your account.

29 EN 6 Check for updates For updates of your Smar t Home devices and the Philips Smart Home app, you can receive messages on your mobile device. Follow the onscreen instructions to complete the updating.

30 EN 7 Technical data Sensors (for indoor use only) Power • Two AAA alkaline batteries Connectivity • Zigbee Motion sensor Detection method • Passive Infra red Door and window sensor Operating temperature & humidity • 32°F to 104°F (0°C to 40°C), 10% to 90% Temperature and humidity sensor Opera...