Page 2 - HUDSON 9; Revision List; Version; Initial release, Draft Version
HUDSON 9 2 Revision List Version Release Date Revision History A00 Apr.02, 2008 Initial release, Draft Version Add CTV Model 190V9FB/27, 190V9FB05 and 190V9FB/00 A01 Apr.10, 2008 Add CTV Model 190V9FB/97 and it’s Philips 12NC A02 Apr.17, 2008 Add two new panels for 190V9FB/97 A03 Apr.30, 2008 Add CT...
Page 3 - Important Safety Notice; The special tools should be used when and as recommended.; WARNING
HUDSON 9 3 Important Safety Notice Proper service and repair is important to the safe, reliable operation of all Philips Company Equipment. The service procedures recommended by Philips and described in this service manual are effective methods of performing service operations. Some of these service...
Page 4 - Monitor Specifications
HUDSON 9 4 1. Monitor Specifications http://www.wjel.net
Page 5 - LCD Monitor Description; Monitor Block Diagram
HUDSON 9 5 2. LCD Monitor Description The LCD monitor will contain a main board, a power board and a key board which house the flat panel control logic, brightness control logic and DDC. The power board will provide AC to DC Inverter voltage to drive the backlight of panel and the main board chips e...
Page 6 - Operating Instructions; General Instructions; panel of the monitor.; Control Buttons; Front View
HUDSON 9 6 3. Operating Instructions 3.1 General Instructions Press the power button to turn the monitor on or off. The other control buttons are located at the front of the panel of the monitor. By changing these settings, the picture can be adjusted to your personal preferences. - The power cord s...
Page 7 - Rear View
Page 8 - Description of the On Screen Display; When you press the
HUDSON 9 8 3.3 Adjusting the Picture Description of the On Screen Display When you press the button on the front control of your monitor, the On-Screen Display (OSD) Main Controls window will pop up and you can then start making adjustments to your monitor's various features. Use the keys to make yo...
Page 9 - The OSD Tree; to work your way around the different adjustments later on.
HUDSON 9 9 The OSD Tree Below is an overall view of the structure of the On-Screen Display. You can use this as a reference when you want to work your way around the different adjustments later on. http://www.wjel.net
Page 10 - Connect the power cord to the back of the monitor firmly.
HUDSON 9 10 3.4 Connecting to the PC 1) Connect the power cord to the back of the monitor firmly. 2) Connect to PC (a) Turn off your computer and unplug its power cable. (b) Connect the monitor signal cable to the video connector on the back of your computer. (c) Plug the power cord of your computer...
Page 11 - Analog connectors; Factory Preset Display Modes
HUDSON 9 11 4. Input/ Output Specification 4.1 Input Signal Connector Analog connectors Pin No. Description Pin No. Description 1. Red video input 9. DDC +5V 2. Green video input 10. Logic Ground 3. Blue video input 11. Ground 4. Sense (GND) 12. Serial data line (SDA) 5. Cable detect (GND) 13. H. Sy...
Page 15 - Failure Mode Of Panel
HUDSON 9 15 4.4 Failure Mode Of Panel Failure description Phenomenon Vertical block defect Vertical dim lines Vertical lines defect (Always bright or dark) Horizontal block defect Horizontal dim lines Horizontal lines defect (Always bright or dark) Has bright or dark pixel Polarizer has bubbles Pola...
Page 20 - TSUM16FWR SCHEMATIC; LVDS OUTPUT; Top
HUDSON 9 20 6. Schematic 6.1 Main Board 715G2904-1 1 1 2 2 3 3 4 4 5 5 A A B B C C D D XGA/SXGA TSUM16FWR SCHEMATIC LVDS OUTPUT Top 04.Output CMVCC PB[0..9] PA[0..1] PPWR_ON# PA[4..9] 02.Input DSUB_R+ DSUB_G+ DSUB_B+ DSUB_V DSUB_R- DSUB_G- DSUB_B- DET_CABLE DSUB_H DSUB_SOG DDC1_SDA DDC1_SCL DSUB_5V ...
Page 23 - Output
HUDSON 9 23 1 1 2 2 3 3 4 4 5 5 A A B B C C D D S D 2 3 AO3401L 1 G CN403 A5C419 C2C420 A4C421 C3FB402 C3Q404 C2Q405 C3R433 C2R434 A4R435 C1R436 C2 Output PA1 PA8 PB2 PB6 PB2 PA9 PB3 PB5 PB8 PB8 PA0 PB2 PA5 PA6 PB6 PB9 PB[0..9] PA9 PB3 PA[0..1] PB1 PA1 PA7 PB5 PA[4..9] PA6 PA4 PB4 PA0 PB0 PA5 PB0 PA...
Page 33 - Pin; Power Board; AC IN
HUDSON 9 33 8. Wiring Diagram Main Board 9Pin 30 Pin Panel D-SUB TSUM1PFR-LF U401 CN403 89G179J30N501 FFC Cable 1 9 CN404 6 Pin 1 6 CN401 Power Board Key Board 6 Pin AC IN CN902 1 14 CN802 CN801 CN804 CN803 CN901 6 1 CN001 95G 82 014X507 HARNESS 14P (SAN)-9P 1 30 14Pin CN101 HARNESS6P (SANW)-6P 95G8...
Page 34 - Scalar Board Overview; Morning Star chip
HUDSON 9 34 9. Scalar Board Overview Morning Star chip Flash ROM EEPROM D-SUB D-SUB DC-DC Converters DC-DC Converters http://www.wjel.net
Page 35 - Mechanical Instructions; Back View as Fig1
HUDSON 9 35 10. Mechanical Instructions 1. Back View as Fig1 Place the monitor face down on a smooth surface as Fig 1. Be careful to avoid scratch and injury during the uninstallation. Fig1 2. Remove the hinge as Fig2. Remove the three screws remarked in red to remove the hinge as Fig2. Fig2 http://...
Page 37 - a. Remove the two screws marked in red as Fig6.
HUDSON 9 37 Fig5 4. Remove main frame cover as Fig6~Fig7. a. Remove the two screws marked in red as Fig6. b. Disconnect the four connector marked in blue as Fig6. c. Remove the two screws marked in red as Fig7. Fig6 Fig7 http://www.wjel.net
Page 38 - a. Remove the two screws marked in red as Fig8.
HUDSON 9 38 5. Remove power board as Fig8. a. Remove the two screws marked in red as Fig8. b. Disconnect the connector marked in blue as Fig8. Fig8 6. Remove scalar board as Fig9~Fig10. a. Remove the screw remarked in red as Fig9. b. Disconnect the two connectors marked in blue as Fig9. c. Remove th...
Page 39 - Trouble Shooting
HUDSON 9 39 11. Trouble Shooting This page deals with problems that can be corrected by a user. If the problem still persists after you have tried these solutions, contact Philips customer service representative. http://www.wjel.net
Page 41 - Repair Flow Chart
HUDSON 9 41 12. Repair Flow Chart 12.1 Main Board (1). No Power No power Press power key and look if the picture is normal Please reinsert and make sure the AC of 100-240 is normal Reinsert or check the Adapter/Inverter section X401 oscillate waveforms are normal Check U404, Q409 and Q410 Replace U4...
Page 47 - d. Software ISP SN Alignment kits
HUDSON 9 47 13. ISP Instruction 1. When do the part, need the tools as follow: a. An i486 (or above) personal computer or compatible. b. Microsoft operation system Windows 95/98/2000/XP. c. “ PORT95NT.exe” program d. Software ISP SN Alignment kits The kit contents: a. ISP BOARD x1 b. Printer cablex1...
Page 50 - Click
HUDSON 9 50 Click to complete the installation. http://www.wjel.net
Page 51 - Connect to
HUDSON 9 51 Note: After installation, you must restart the PC to take the setup to effect. 3. Connect the ISP board as follow: Connect to the PC LPT Connect to the Philips 190V9 http://www.wjel.net
Page 52 - The process of ISP write is as follows.; running the program as follows:
HUDSON 9 52 4. The process of ISP write is as follows. a. Double-click , running the program as follows: http://www.wjel.net
Page 53 - icon, search the program”
HUDSON 9 53 b. Click icon, search the program” 190V9_TSUM1PFR_LM190E08_TLL_20080319_V101”, and click open: http://www.wjel.net
Page 55 - DDC Instruction; General
HUDSON 9 55 14. DDC Instruction General DDC Data Re-programming In case the main EEPROM with Software DDC which store all factory settings were replaced because a defect, repaired monitor’ the serial numbers have to be re-programmed. It is advised to re- soldered the main EEPROM with Software DDC fr...
Page 56 - Second, you must install the
HUDSON 9 56 2. Install the “WinDDC_ setup” Second, you must install the . The processing as follows: http://www.wjel.net
Page 59 - Take analog DDC write for example, as follow; appear as follow Figs
HUDSON 9 59 4. Take analog DDC write for example, as follow a. Double-click , appear as follow Figs : http://www.wjel.net
Page 61 - Analog
HUDSON 9 61 190V9 EDID Analog 128 bytes EDID Data (Hex): 00 01 02 03 04 05 06 07 08 09 10 11 12 13 14 15 0: 00 FF FF FF FF FF FF 00 41 0C 20 C0 01 01 01 01 16: 0C 0B 01 03 0E 26 1E 78 2A A1 50 A3 57 4C 9D 25 32: 11 50 54 BF EF 80 71 4F 81 40 81 80 01 01 01 01 48: 01 01 01 01 01 01 30 2A 00 98 51 00 ...
Page 63 - White Balance, Luminance Adjustment; restart PC after finish installing.
HUDSON 9 63 15. White Balance, Luminance Adjustment 1. Apparatuses and program: analyzer CA-210, PC, tool, FGA adjustment program (PHILIPS170V9.DDCI), Pattern generator. 2. Equipment installation: a. Connect analyzer CA-210 to PC by USB connector, install drive program CA-SDK Ver4.00 for CA-210 and ...
Page 64 - Temp
HUDSON 9 64 4. Color Temp confirmation Connect the signal to the monitor, the monitor display white-picture, use CA-210 to measure the Color Temp of the screen center and select the OSD to make sure whether the Color Temps accord with the SPEC. http://www.wjel.net
Page 65 - Monitor Exploded View
HUDSON 9 65 16. Monitor Exploded View 1 2 3 4 5 6 7 8 1 2 3 4 5 6 7 8 F E D C B A 190V9 8 7 6 5 4 3 2 1 A B C D E F Item Part No. 1 23 4 5 6 7 8 BEZEL PANEL SCALAR BOARD ASSY POWER BOARD ASSY REAR COVER 190V9 STAND_BASE ASS'Y KEY BOARD ASSY KEY PAD http://www.wjel.net
Page 66 - Item Location Philips
HUDSON 9 66 17. Recommended & Spare Parts List 190V9FB/97(1) Item Location Philips 12NC PCM Codes Description 1 FQ106 996510017730 Q34G0368ADTE1B0130 BEZEL_190V 2 E750 996510016251 750GLG190E8G23N000 PANEL LM190E08-TLG2 GZ LGD 2 E750 996510016074 750GLG190E8G43N000 PANEL LM190E08-TLG4 GZ LGD 2 E...
Page 67 - Service Kit; Description Part
HUDSON 9 67 U402 996510015572 705GQ756218 MCU ASS'Y(HSD) IC903 996500036055 056G 139 3A IC PC123Y22FZ0F IC901 996510014843 056G 379 98 IC LD7552DPS SOP-8 IC801 996500036059 056G 608 10 IC OZ9938GN-B SOIC-16 IC904 996510002780 056G 158 10 T IC AZ431AZ-AE1 TO-92 BY AAC PT801 996510014840 S80GL19T32V T...
Page 68 - Different Parts List
HUDSON 9 68 18. Different Parts List Diversity of 190V9FB/62(1) compared with 190V9FB/97(1) 190V9FB/62 (1) 190V9FB/97 (1) Location Philips 12NC PCM Codes Description Philips 12NC PCM Codes Description FQ205 705GQ834006 CUSHION ASSY 996510016252 705GQ8CS006 CUSHION ASSY Diversity of 190V9FB/27(1) com...
Page 70 - Location; XFMR POWER 490uH TPV-PT
HUDSON 9 70 Diversity of 190V9FB/94(2) compared with 190V9FB/97 (1) 190V9FB/94(2) 190V9FB/97 (1) Location Philips 12NC PCM Codes Description Philips 12NC PCM Codes Description F901 996510006276 084G 56 4W FUSE 4.0A 250V 996510013724 084G 56 4 B FUSE 4A 250V F903 996510006276 084G 56 4W FUSE 4.0A 250...
Page 71 - General Product Specification
HUDSON 9 71 19. General Product Specification CONTENTS 1 FOREWORD 2 PRODUCT PROFILE 2.1 LCD 2.2 SCANNING FREQUENCIES 2.3 AMBIENT TEMPERATURE: 0 ° C - 40 ° C 3 ELECTRICAL CHARACTERISTICS 3.1 INTERFACE SIGNALS 3.2 INTERFACE 3.3 TIMING REQUIREMENT 3.4 HORIZONTAL SCANNING 3.5 VERTICAL SCANNING 3.6 POWER...
Page 74 - Scanning frequencies
HUDSON 9 74 Color gamut : 72% Gate IC : Novatek Source IC : Novatek Response time : 5 ms 2.2 Scanning frequencies Hor. : 30 – 83 K Hz Ver.: 56 - 76 Hz Video dot rate: 165 MHz (140MHz for EDID) Power input: 90-264 V AC, 50/60 ± 2 Hz Power consumption : : 36 W typical Functions: D-SUB analog R/G/B sep...
Page 77 - Off
HUDSON 9 77 3.3.3 Software control functions via OSD / control adjustable functions: Any deviation, then refer to PVT Exit sample. Please refer to following Hudson8 OSD definitions Level 1 Level 2 Level 3 Default Picture Brightness (0~100) 100 Contrast (0~100) 50 Color Color Temp. (5000K,6500K,7500K...
Page 79 - Brightness uniformity
HUDSON 9 79 signal sources must have 75 ohm output impedance. (2) Luminance setting : controls to be set to 300 nits (typical ) with full screen 100 % duty cycle white signal (3) Warm up: more than 30 minutes after power on with signal supplied. (4) Ambient light: 400 -- 600 lux. (5) Ambient tempera...
Page 80 - sRGB
HUDSON 9 80 6500K/sRGB x = 0.313 ± 0.02 y = 0.329 ± 0.02 sRGB x = 0.313 ± 0.02 y = 0.329 ± 0.02 5000K x = 0.346 ± 0.02 y = 0.359 ± 0.02 Production alignement specification CIE coordinates (x,y) 11500K x = 0.272 ± 0.005 y = 0.283 ± 0.005 9300K x = 0.283 ± 0.005 y = 0.297 ± 0.005 8200K x = 0.292 ± 0.0...
Page 81 - If paint is used
HUDSON 9 81 5.7 Resins z RoHS required z WEEE required. z Resin type/selection refer to Project Book Section 7.2 Plastic material. 5.8 If paint is used z RoHS required z WEEE require z If new painting type need to implement, refer to UN-D 1235. 5.9 Plastic mold tooling z Tooling to be designed to mi...
Page 82 - A. Transportation test specification for all regions
HUDSON 9 82 H :| L-R | ≤ 1. 5 ㎜ V :| U-D | ≤ 1. 5 ㎜ 2.Black side on the left and right is symmetrical, not cut side. z Gap between bezel and rear cover 0.4 mm ( Typ. ) z Step between bezel and rear cover Left, right and top : ≤ 0.6mm Bottom and corner: ≤ 1.1mm z "Wobble", "Twist", et...
Page 84 - BLACK DOT DEFECTS
HUDSON 9 84 BLACK DOT DEFECTS ACCEPTABLE LEVEL MODEL 190V9 1 dark sub-pixel 5 2 adjacent dark sub-pixels 2 3 adjacent dark sub-pixels (one white pixel) 1 Distance between two black dots 15mm Black dot defects within 20 mm circle* 1 Total black dot defects of all type 5 TOTAL DOT DEFECTS ACCEPTABLE L...
Page 85 - Fig 1: Measurement locations of Brightness Uniformity; YA; Fig 3: Cross talk Pattern; YB
HUDSON 9 85 Fig 1: Measurement locations of Brightness Uniformity Fig 2: Cross talk pattern Gray level 46 (64 Gray level) YA 1/2 1/2 1/6 Fig 3: Cross talk Pattern Center at Gray level 0 (Black) YB 1/2 1/2 1/6 1/3 1/3 1/3 1/3 1/3 http://www.wjel.net
Page 91 - NOT REQUIRED
HUDSON 9 91 Sa Korean Safety Control law IEC 60950 EK certificate OEM Yes No NOT REQUIRED KOREA E Regulations laws: EMI 1996-78, 80. EMS 1996-79,81 MIC certificate OEM Yes No NOT REQUIRED SINGAPOR E Sa IEC60950 PSB certificate OEM Yes Yes Supplier to provide local representative Sa GB4943-2001 CCC c...
Page 95 - EMC Requirements; Restriction on the use of certain hazardous substances.; Ongoing Regulatory
HUDSON 9 95 10.2 EMC Requirements Supplier DVT EMI test result must be submitted prior to DVT samples delivery, and PVT EMI test result must be submitted again prior to PVT samples delivery, which also has to meet Philips' immunity testing specification. 10.3 RoHS Restriction on the use of certain h...