Page 2 - Safety Instructions; Read this first
22BDL7324L ii Safety Instructions Read this first The latest User’s Manual, Quick Start Guide and FAQ are available for download from the Philips website. Warning & Symbols Refer to the following graphic symbols to alert you to important information: Notes: useful information that help you get b...
Page 3 - Environmental absolute ratings
22BDL7324L iii Environmental absolute ratings Item Min. Max. Unit Storage temperature -20 50 °C Operation temperature -20 45 °C Storage humidity 10 85 % RH Operating humidity 10 80 % RH • LED display temperature need to be 25 degrees Celsius at all time for better luminance performance.• Only the li...
Page 4 - EU Declaration of Conformity; ESD Warnings
22BDL7324L iv Read and follow these instructions when connecting and using your display: • Unplug the display if you are not going to use it for an extensive period of time. • Unplug the display if you need to clean it with a slightly damp cloth. The screen many be wiped with a dry cloth when the po...
Page 5 - Polish Center for Testing and Certification Notice
22BDL7324L v Polish Center for Testing and Certification Notice The equipment should draw power from a socket with an attached protection circuit (a three-prong socket). All equipment that works together (computer, display, printer, and so on) should have the same power supply source. The phasing co...
Page 6 - How to connect a plug; North Europe (Nordic Countries) Information
22BDL7324L vi Information for U.K. only (A) (B) WARNING - THIS APPLIANCE MUST BE EARTHED.Important: This apparatus is supplied with an approved moulded 13A plug. To change a fuse in this type of plug proceed as follows:+ 1. Remove fuse cover and fuse.2. Fit new fuse which should be a BS 1362 5A,A.S....
Page 7 - China RoHS; RoHS; 环保使用期限
22BDL7324L vii China RoHS 根据中国大陆《电器电子产品有害物质限制使用管理办法》，以下部分列出了本产品中可能包含的有害物质的名称和含量。 部件名称 有害物质 铅 (Pb) 汞 (Hg) 镉 (Cd) 六价铬 (Cr (VI)) 多溴联苯 (PBB) 多溴二苯醚 (PBDE) 铁框 O O O O O O 发光二极管 X O O O O O 电路板组件 * X O O O O O 电源线 X O O O O O 其他线材 X O O O O O 本表格依据 SJ/T 11364 的规定编制。 *: 电路板组件包括印刷电路板及其构成的零部件，如电阻、电容、集成电路、连接器等...
Page 8 - Waste Electrical and Electronic Equipment-WEEE; Attention users in European Union private households
22BDL7324L viii 單元 限用物質及其化學符號 鉛 (Pb) 汞 (Hg) 鎘 (Cd) 六價鉻 (Cr +6 ) 多溴聯苯 (PBB) 多溴二苯醚 (PBDE) 鐵框 ○ ○ ○ ○ ○ ○ 發光二極管 － ○ ○ ○ ○ ○ 電路板組件 － ○ ○ ○ ○ ○ 電源線 － ○ ○ ○ ○ ○ 其他線材 － ○ ○ ○ ○ ○ 備考1.〝○〞係指該項限用物質之百分比含量未超出百分比含量基準值。 備考2.〝－〞係指該項限用物質為排除項目。 警語 : 使用過度恐傷害視力。 注意事項 : (1) 使用30分鐘請休息10分鐘。 (2) 未滿2歲幼兒不看螢幕，2歲以上每天看螢幕不要超過1小...
Page 9 - Attention users in United States:; Restriction on Hazardous Substances statement (India); Após o uso, as pilhas
22BDL7324L ix Attention users in United States: Please dispose of according to all Local, State and Federal Laws. For the disposal or recycling information, contact: www.mygreenelectronics.com or www.eiae.org. End of Life Directives-Recycling Your new Public Information Display contains several mate...
Page 10 - Cleaning
22BDL7324L x Information for EAC Month and year of manufacturing please refer information in Rating label. Name and location of manufacturer ООО “Профтехника” Адрес: 3-й Проезд Марьиной рощи, 40/1 офис 1. Москва, 127018, Россия Importer and information Наименование организации: ООО “Профтехника” Адр...
Page 11 - Table Of Contents
22BDL7324L xi Table Of Contents 1. Preparations .................................................................. 1 1.1. Unpacking ........................................................... 11.2. Package Contents ............................................. 11.3. Holding the cabinet ................
Page 12 - Preparations; Unpacking
22BDL7324L 1 1. Preparations 1.1. Unpacking Warning: To prevent damage to the LED panel, wear anti-static gloves before installing/touching the display.After unpacking, do not place the display vertically on the floor, an accident such as fall may be caused.1. Use a pair of scissors to cut sealing t...
Page 14 - Product overview
22BDL7324L 3 2. Product overview 2.1. Front view 2 3 11 2.2. Rear view 4 2.3. Side view Left side Right side 2.4. Top view 2.5. Bottom view No. Component No. Component Data connector (s) Power Out connector Power In connector CHECK button The Data connector ( ) is an RJ45 connector, but it cannot be...
Page 15 - Preparation; CHECK
22BDL7324L 4 3. Preparation 3.1. Testing the cabinet 1. Power on the product by connecting the power cable from the cabinet to the power outlet.2. Press the CHECK button on the back of each cabinet to check if the product can operate normally. 3. Check whether each color is displayed normally on the...
Page 16 - Installation; Not included
22BDL7324L 5 4. Installation Precautions when handling the cabinets: • Do not drop or apply shock/vibration to the product. Strong impacts may damage the component inside.• Only a qualified service technician should perform installation.• Only use approved cabinets. • Be careful not to damage the co...
Page 22 - Connection; Connecting the signal and power cables; Cautions; Max. daisy chain cable current rating: 10 Amp; Power Out; Power In; Caution
22BDL7324L 11 5. Connection 5.1. Connecting the signal and power cables LAN cable Power cable (daisy chain) LED display controller * * ** * * Optional accessories** Power plug types vary by country/region. Cautions Connection is allowed up to 8 cabinets when the 110 VAC power supply is used. Connect...
Page 23 - Installing the modules
22BDL7324L 12 6. Installing the modules When installing the modules, refer to the instruction and installation order specified below. Note that screen output may not be displayed properly if instructions are not followed.Every cabinet has a serial number supplied and this serial number is located on...
Page 25 - Dehumidification function; Purpose of dehumidification in LED display
22BDL7324L 14 7. Dehumidification function Purpose of dehumidification in LED display Internal parts and elements tend to corrode during storage when the LED display is left unused for a long period of time in a humid environment. In particular when moisture gets into the diode, it may cause blurred...
Page 30 - Configuring dehumidification settings
22BDL7324L 19 7.3. Configuring dehumidification settings When the LED display is operated normally over a period of time, follow the steps below before you turn the display off: 1. Run the program Nova LCT V5.4.2 Plus . 2. After screen configuration is complete, click Brightness . See Figure 2-1. Fi...
Page 32 - Activating Dehumidification function; Cancelling Dehumidification function; unused
22BDL7324L 21 7.4. Activating Dehumidification function 1. Turn off the LED display and power off the LED display controller.2. When using the LED display, turn on the LED display controller and the LED display.* You can notice that, according to the dehumidification time you set, the brightness of ...
Page 33 - Using the LED display controller
22BDL7324L 22 8. Using the LED display controller The LED display controller is a device served for managing any type of video and data sources for any screen configuration. Visit Novastar website to learn more about Novastar’s LED display controller and select the one that suit your needs according...
Page 34 - Appendices; Appendix A. Warranty Statement; Warranty policy for Philips Professional Display Solutions
22BDL7324L 23 Appendices Appendix A. Warranty Statement Warranty policy for Philips Professional Display Solutions Thank you for purchasing this Philips product. Philips products are designed and manufactured with high standards and deliver high quality performance, ease of use and ease of installat...
Page 36 - Appendix B. Troubleshooting; Symptom
22BDL7324L 25 Appendix B. Troubleshooting Frequently asked questions and common problems that may occur while using the system are explained in this section. Observe the following table containing a list of symptoms and the actions to take to solve the problems.If a problem persists after performing...
Page 37 - Appendix C. Dew point VS. Relative Humidity
22BDL7324L 26 Appendix C. Dew point VS. Relative Humidity The table below explains the relationship between temperature/relative humidity and dew point. Celsius ( ° C) -20 -20 -20 -20 -20 -20 -20 -20 Relative Humidity (%) 10 20 30 40 50 60 70 80 Dew point ( ° C) -43.87 -37.24 -33.15 -30.15 -27.76 -2...
Page 38 - Appendix D. Optional Components/Accessories; CTN
22BDL7324L 27 Appendix D. Optional Components/Accessories If you need to purchase the components or accessories listed below, please contact your local service center for support. CTN Commercial description CRD17024/00 LED module, 7x24-series, SMD1515 Copper CRD17031/00 LED module, 7x31-series SMD21...
Page 41 - Appendix E. Technical Specifications; Power
22BDL7324L 30 Appendix E. Technical Specifications Picture/Display Peak brightness (nits) 1600* Max. brightness (nits) ±1200* Color Temperature (K) default 6500±500 Color Temperature (K) adjust range 4000-9500 (by software) Viewing Angle (°) H/V 145/145 Brightness Uniformity ≥ 97% Transparent rate(%...
Page 43 - Appendix F. Magnet tension; Dangerous
22BDL7324L 32 Appendix F. Magnet tension 0.4~0.5Kg (Module Weight) 60 o C 80 o C 120 o C (Safety redundancy, Follow UL 2442) 2.25Kg 6.4Kg 7.0Kg 2.0Kg Dangerous Area Temperature Magnets tension 1. Each module uses 9 N52 NdFEB magnets. After measurement, the tensile force of N52 NdFEB magnets at vario...
Page 44 - Installation power cable measure
22BDL7324L 33 Appendix G. Power/Data cable measure Installation power cable measure
Page 46 - Installation data cable measure
Page 48 - Appendix H. Mounting scheme; Manufacturer Default Alignment Pin
22BDL7324L 37 Appendix H. Mounting scheme Below you will find some configuration examples for mounting scheme. Manufacturer Default Alignment Pin Alignment screw thread hole Alignment hole Opening for cable 1 L-4-3-2 Installation R-4-3-2 Installation L-4-2-3 Installation R-4-2-3 Installation 1 2 3 5...
