Philips 107E - Manual

VIDEO • Video dot rate 108 MHz • Input impedance - Video 75 ohm - Sync 4.7 kOhm • Input signal levels 0.7 Vpp • Sync input signal Separate sync • Sync polarities Positive and negative WHITE COLOR TEMPERATURE Chromaticity CIE coordinates: • at 9300 degrees K x = 0.283 / y = 0.297 • at 6500 degrees K ...

If you have VESA's DPMS compliance display card or software installed in your PC, the monitor canautomatically reduce its power consumption when not in use. And if an input from a keyboard, mouse orother input device is detected, the monitor will automatically "wake up". The following table ...

Pin Assignment The 15-pin D-sub connector (male) of the signal cable (IBM systems): Pin No. Assignment Pin No. Assignment 1 Red video input 9 +5V DDC supply 2 Green video input 10 Logic ground 3 Blue video input 11 Identical output - connectedto pin 10 4 Identical output - connectedto pin 10 12 Seri...

Installing your Monitor Front View • Rear View • 6G3B11 Multimedia Base (option) Front View Power button switches your monitor on. OK button which when pressed will take you to the OSD controls Contrast hotkey. When the "-" button is pressed, the adjustment controlsfor the CONTRAST will show...

"-" and "+" buttons, are used for adjusting the OSD of your monitor. LightFrame™ hotkey. When the button is pressed, the adjustmentcontrols for LightFrame™ will show up. RETURN TO TOP OF THE PAGE Rear View Installing your Monitor file:///D|/EDFU/LF3/lf3manual/english/INSTALL_6/INSTAL...

On-Screen Display Description of the On-Screen Display • The OSD Tree • The OSD Controls Description of the On Screen Display What is the On-Screen Display? This is a feature in all Philips monitors which allows an end-user to adjust screen performance of monitorsdirectly through an on-screen instru...

RETURN TO TOP OF THE PAGE The OSD Tree Below is an overall view of the structure of the On-Screen Display. You can use this as reference when youwant to later on work your way around the different adjustments. On-Screen Display file:///D|/EDFU/LF3/lf3manual/english/OSD_2/OSDDESC.HTM (2 of 3) [12/19/...

Customer Care & Warranty PLEASE SELECT YOUR COUNTRY/AREA TO READ THE WARRANTY COVERED: WESTERN EUROPE: Austria • Belgium • Cyprus • Denmark • France • Germany • Greece • Finland • Ireland • Italy • Luxembourg • the Netherlands • Norway • Portugal • Sweden •Switzerland • Spain • United Kingdom EA...

Frequently Asked Questions 1. What does the "Designed for Windows" logo signify? The "Designed for Windows" logo means your Philips monitor fulfills the requirements andrecommendations of the PC9x (97, 98, or 99) System Design Guide and passes stringentWHQL tests. 2. What is USB? Thi...

5. Where can I buy a USB hub for my Philips monitor? Philips provides an optional USB hub (type number: PCUH411) which can be attached to thebase or pedestal of Philips monitors. Contact your dealer/reseller for details. 6. What models are Mac compatible? All listed Philips monitors are Mac compatib...

A low refresh rate or electrical interference typically causes flickering in the picture. Possiblesolutions include the following: Verify that the proper drivers are installed for your video card¡ª ● Make sure that all electrical devices (such as mobile phones) are at least 1m from themonitor ● Plac...

LightFrame " consists of a software application and an Integrated Circuit (IC) embedded in the monitor. Together, they boost brightness and sharpness in a user defined window or screenarea. Unique LightFrame TM technology dramatically improves photo and video display quality. 18. Why is LightFra...

22. What will happen when my system is no longer connected to a LightFrame " enabled monitor - for example, when I take my notebook on the road? Philips exclusive LightFrame " feature requires the combined operation of hardware that resides in your monitor and software installed on your syst...

27. What are Philips Multimedia Base's specifications? See detailed Multimedia Base specifications on the product information page. 28. Why is a Multimedia Base better than separate speakers? The major advantage of the Multimedia Base is its minimal space requirements. In fact, ithardly uses any ext...

32. How does Auto Calibrate work? During the calibration process, different predefined black and white images are displayed onthescreen. The beam currents of the red, green and blue cannon are accurately measured andcompared to the original values stored in the monitor. By readjusting gain values of...

newer models have this option in the On Screen Display under Input Signal Selection. Video card may be not be a VESA standard (try the monitor with another computer) ● 37. Why does my monitor display "Out of Range"? The video card installed in your computer may be too high for the monitor 's...

Yes, when degaussing your monitor via the OSD, it is normal for the monitor to make arelatively loud noise. Please be aware that many models will not degauss more than once within any given time period (up to 10 minutes). This is due to the unit having a temperaturesensitive resistor. While the unit...

Select under Advanced Controls in the monitor 's OSD. Most computers require it to be set at 0.7V. Please review the following for possible solutions: If the OSD menu is also dim, please contact service for repair ● Reset the monitor via the OSD menu ● Change the color temperature settings to 9300 c...

Glossary A B C D E F G H I J K L M N O P Q R S T U V W X Y Z A Autoscan A microprocessor-based feature of Philips Brilliance monitors is able to detect automatically horizontal andvertical frequencies of input signals with those of the installed video card. An autoscan monitor can thusoperate with a...

Points where convergence error is specified . Convergence-error correction A method of correcting for convergence error to insure that all three beams land simultaneously in the sametriad. This is usually accomplished by means of special convergence-error correction coils in the deflectionyoke. CRT ...

Dot rate Frequency in MHz of the dot clock. It is a measure of the speed with which data is transferred between thevideo card and subsequent processing circuitry. Also known as video dot rate. RETURN TO TOP OF THE PAGE E Electromagnetic radiation standards International standards set to limit electr...

In 1991, the Swedish Tjänstemannens Central Organization (TCO, Swedish confederation of ProfessionalEmployees ) set a standard even more severe than MPR-II, especially for alternating electric fields (AEF).The TCO standard is more severe since not only are the permitted field levels reduced compared...

Also called line frequency and expressed in kHz, it is the number of video lines written on the screen everysecond (from left to right). The higher the horizontal scanning frequency, the better the resolution (i.e., thehigher the resolution and/or the higher the refresh rate). RETURN TO TOP OF THE P...

L Linearity The degree to measure the actual location of a pixel on the screen corresponds with its intended location. (see figure ) Line frequency See Horizontal scanning frequency. Low-emission monitor A monitor that complies with international standards on radiation. See Electromagnetic radiation...

M Moiré effect A fringe pattern arising from the interference between two superimposed line patterns. In a monitor it comes from the interference between the shadow mask pattern and the video information(video moiré), and between the shadow mask pattern and the horizontal line pattern (scan moiré). ...

R Raster The area on screen that electron beam can reach. Refresh rate See Vertical scanning frequency. Resolution The number of pixels that can be displayed on the screen. The resolution is specified as the number ofpixels in a line multiplied by the number of horizontal lines. See also video graph...

The ARAS coating reflects only about 0.5% of the incident light. AGRAS (Anti-Glare anti-Reflection Anti-Static) coating . A combined anti-reflection, anti-glare, anti-static coating. Self-test function A monitor equipped with hardware or software to automatically detect cable connection status. Shap...

SOG (Synchronization On Green) A properly functioning color monitor requires five kinds of signals: horizontal sync pulse, vertical sync pulse,red color signal, green color signal and blue color signal. Signals from a PC are transmitted to a monitorusing one of three methods: 1. Separate sync: Horiz...

See rotation function. Trapezoid distortion See Geometrical distortion. TTL signal A TTL (Transistor-transistor-logic) signal is a digital signal level for controlling the screen colors. With TTLdriving, the red, green and blue signals can only be switched on or off or provided with an intensity sig...

Download and Print This page provides an option to read the manual in .pdf format. PDF files can be downloaded into your harddisk, then viewed and printed with Acrobat Reader or through your browser. If you do not have Adobe¨ Acrobat Reader installed, click on the link to install the application. Ad...

Troubleshooting Safety Precautions and Maintenance • Troubleshooting • Regulatory Information • Other Related Information Common Problems Having trouble? Something not working? Before calling for help, try these suggestions. Having thisproblem? Check these items No Picture (Power LED not lit) Make s...

Regulatory Information TCO '99 Information • TCO'99 Environmental Requirements • CE Declaration of Conformity • Energy Star Declaration • Federal Communications Commission (FCC) Notice (U.S. Only) • Commission Federale de la Communication (FCC Declaration) • EN 55022 Compliance (Czech Republic Only)...

Approval requirements cover a wide range of issues: environment, ergonomics, usability, emission of electricand magnetic fields, energy consumption and electrical and fire safety. The environmental demands impose restrictions on the presence and use of heavy metals, brominated andchlorinated flame r...

electronics components must not contain any cadmium. Mercury** Mercury is sometimes found in batteries, relays and switches. It damages the nervous system and is toxic inhigh doses. The relevant TCO'99 requirement states that batteries may not contain any mercury. It alsodemands that mercury is not ...

- TCO95, TCO99 (Requirement for Environment Labelling of Ergonomics, Energy, Ecology andEmission,TCO: Swedish Confederation of Professional Employees) for TCO versions RETURN TO TOP OF THE PAGE Energy Star Declaration PHILIPS 107E5* This monitor is equipped with a function for saving energy which su...

This equipment has been tested and found to comply with the limits for a Class B digitaldevice, pursuant to Part 15 of the FCC Rules. These limits are designed to providereasonable protection against harmful interference in a residential installation. Thisequipment generates, uses and can radiate ra...

Toutes modifications n'ayant pas reçu l'approbation des services compétents en matière deconformité est susceptible d'interdire à l'utilisateur l'usage du présent équipement. N'utiliser que des câbles RF armés pour les connections avec des ordinateurs ou périphériques. CET APPAREIL NUMERIQUE DE LA C...

RETURN TO TOP OF THE PAGE MIC Notice (South Korea Only) Class B Device Please note that this device has been approved for non-business purposes and may be used in anyenvironment, including residential areas. RETURN TO TOP OF THE PAGE Polish Center for Testing and Certification Notice The equipment s...

RETURN TO TOP OF THE PAGE North Europe Information (Nordic Countries) Placering/Ventilation VARNING: FÖRSÄKRA DIG OM ATT HUVUDBRYTARE OCH UTTAG ÄR LÄTÅTKOMLIGA, NÄRDU STÄLLER DIN UTRUSTNING PÅPLATS. Placering/Ventilation ADVARSEL: SØRG VED PLACERINGEN FOR, AT NETLEDNINGENS STIK OG STIKKONTAKT ERNEMT...

Paikka/Ilmankierto VAROITUS: SIJOITA LAITE SITEN, ETTÄ VERKKOJOHTO VOIDAAN TARVITTAESSA HELPOSTIIRROTTAA PISTORASIASTA. Plassering/Ventilasjon ADVARSEL: NÅR DETTE UTSTYRET PLASSERES, MÅ DU PASSE PÅ AT KONTAKTENE FORSTØMTILFØRSEL ER LETTE Å NÅ. RETURN TO TOP OF THE PAGE BSMI Notice (Taiwan Only) RETU...

Aus ergonomischen Gründen wird empfohlen, die Grundfarben Blau und Rot nicht auf dunklemUntergrund zu verwenden (schlechte Lesbarkeit und erhöhte Augenbelastung bei zu geringemZeichenkontrast wären die Folge). Der arbeitsplatzbezogene Schalldruckpegel nach DIN 45 635 beträgt 70dB (A) oder weniger. A...

have a value of 5A. If a plug without a fuse isused, the fuse at the distribution board shouldnot be greater than 5A. Note: The severed plug must be destroyed toavoid a possible shock hazard should it beinserted into a 13A socket elsewhere. How to connect a plug The wires in the mains lead are colou...

6G3B11 Multimedia Base (option) Front View • Rear View • Technical Specifications • Description of the Controls • Installing your Multimedia Base • Power adapter Installation Technical Specifications* • Output power 2 x 1.5W RMS / 36W PMPO • Bass Boost • Headphone connection 3.5 mm jack • Microphone...

D. Microphone jack Attach your microphone here. E. Audio In Connect this to the audiooutput of your PC. F. MIC Out Connect this to the microphoneoutput of your PC. G. DC Input Connect power input here. RETURN TO TOP OF THE PAGE Installing your Multimedia Pedestal 1. To INSTALL Slide the pedestal, al...

2. To UN-INSTALL Lift the back hook from the hole on the bottomplate of your monitor. ● Slide out the pedestal the opposite direction (fromwhen you installed it). ● RETURN TO TOP OF THE PAGE Power adapter Installation Installing the adapter There are two (2) ways of installing the adapterA. T-connec...

The OSD Controls Description of the On-Screen Display • The OSD Tree The OSD Controls : Brightness (HotKey) • Contrast (HotKey) • Language • Input Signal Selection • Zoom • Adjust Horizontal • Adjust Vertical • Adjust Shape • Adjust Color • Reset to Factory Settings • Extra Controls • Close Main Con...

2) Press the or button to adjust the contrast. 3) When the contrast is adjusted to the level desired, press to confirm and the CONTRAST window will disappear with the new adjustment saved. RETURN TO TOP OF THE PAGE LANGUAGE The ON SCREEN DISPLAY shows its settings in one of eight languages. The defa...

3) Press the or button until the desired language is highlighted. 4) Press the button to confirm your selection and return to MAIN CONTROLS window. CLOSE MAIN CONTROLS will be highlighted. RETURN TO TOP OF THE PAGE INPUT SIGNAL SELECTION (Not available in all models) INPUT SIGNAL SELECTION determine...

2) Press the button until INPUT SIGNAL SELECTION is highlighted. 3) Press the button. The INPUT SIGNAL SELECTION window appears. 4) Press the or button to highlight INPUT B or INPUT A. 5) Press the button to confirm your selection and Press again return to the MAIN CONTROLS window. CLOSE MAIN CONTRO...

ADJUST HORIZONTAL ADJUST POSITION under ADJUST HORIZONTAL shifts the image on your screen either to the left or right.Use this feature if your image does not appear centered. ADJUST SIZE under ADJUST HORIZONTALexpands or controls the image on your screen, pushing it out toward the left and right sid...

4) Press the or button to move the image to the left or right. 5) When the position is adjusted, press the button to confirm. Press the to highlight SIZE, press to confirm. 6) To adjust the horizontal size, press the or button. 7) When the size is adjusted, press the button to confirm. Press again t...

6) To adjust the vertical size, press the or button. 7) When the size is adjusted, press the button to confirm. Press return to MAIN CONTROLS window. CLOSE MAIN CONTROLS will be highlighted. RETURN TO TOP OF THE PAGE ADJUST SHAPE ADJUST SIDE CURVE ADJUST SIDE CURVE under ADJUST SHAPE allows you to a...

5) To adjust the pincushion, press the or button,press the to confirm. 6) When the pincushion is adjusted, press the button to highlight BALANCED. Press to confirm. 7) To adjust the balanced pincushion, press the or button.Press to confirm. 8) When the balanced pincushion is adjusted, press the butt...

ROTATE IMAGE is highlighted. ROTATE IMAGE (Not available in all models) ROTATE IMAGE under ADJUST SHAPE allows you to adjust one of the five preset options. These twooptions are PINCUSHION and BALANCED pincushion. Note: use this feature only when the picture is notsquare. 1) Press the button on the ...

5) Press the button. The ROTATE IMAGE window appears. ROTATE should be highlighted. 6) To adjust the rotation, press the or button. 7) When the rotation is adjusted, press the button to confirm. Press to return to the ADJUST SHAPE window. BACK TO MAIN CONTROLS should be highlighted. 8) Press the but...

button to confirm you selection. Press again to return to the MAIN CONTROLS window. CLOSE MAIN CONTROLS will be highlighted. 6a) If USER PRESET is highlighted, press the button to highlight RED. Next, press the to confirm. Press or button to adjust the color red. 6b) When finished with RED, press to...

EXTRA CONTROLS DEGAUSS EXTRA CONTROLS is a set of three features, including DEGAUSS. Degaussing removes electromagneticbuild up that may distort the color on your screen. 1) Press the button on the monitor. The MAIN CONTROLS window appears. 2) Press the button until EXTRA CONTROLS is highlighted. 3)...

5) To degauss your screen, press the button. Your screen will be degaussed, then the MAIN CONTROLS window will reappear. CLOSE MAIN CONTROLS will be highlighted. ADJUST MOIRE (Not available in all models) EXTRA CONTROLS is a set of three features, including ADJUST MOIRE. Moire is a fringe pattern ar...

5) To adjust the horizontal moire, press the or button. 6) When the horizontal moire is adjusted, press to confirm. Press the button to highlight VERTICAL. 7) To adjust the vertical moire, press to confirm. Then press or button to adjust. 8) When the vertical moire is adjusted, press the to confirm....

Your International Guarantee Dear Customer, Thank you for purchasing this Philips product which has been designed and manufactured to the highestquality standards. If, unfortunately, something should go wrong with this product Philips guarantees free of charge labor andreplacement parts irrespective...

LIMITED WARRANTY(Computer Monitor) Click here to access the Warranty Registration Card One Year Exchange* *Product will be exchanged with a new or renewed to original specifications unit within two businessdays for the first year. WHO IS COVERED? You must have proof of purchase to receive warranty s...

For more information, contact the Philips Customer Care Center by calling (877) 835-1838 (U.S.A.customers only) or (903) 242-4804. Before Requesting Service... Please check your owner's manual before requesting service. Adjustments of the controls discussedthere may save you a service call. TO GET W...

All Philips monitors are designed and manufactured to high standards and deliver high-qualityperformance, ease of use and ease of installation. Should you encounter any difficulties whileinstalling or using this product, please contact Philips directly to benefit from your Philips F1rstChoice Warran...