Page 2 - PFAFF 2; Contents; Page
PFAFF 2 Contents Checking and adjustment aid ..................................................................................... 3 1 Preliminary adjustment of the needle height ............................................................. 4 2 Zeroing the feed motion ..................................
Page 4 - Checking and adjustment aid; required needle bar positions very precisely.
PFAFF 3 Adjustment hole 1 = 0.6 mm past top dead center of the needle bar (0.6 past t.d.c.). Adjustment hole 3 = 0.6 mm past the bottom dead center of the needle bar (0.6 past b.d.c). Adjustment hole 4 = 1.8 mm past the bottom dead center of the needle bar (needle rise position). Adjustment hole 5 =...
Page 5 - PFAFF; Preliminary adjustment of needle height; Requirement
4 PFAFF 1 Preliminary adjustment of needle height Requirement With the needle bar at b.d.c. there must be a clearance of 16.5 mm between needle holder and needle plate. 2 1 ● Move needle bar 1 (screw 2 ) according to the requirement. Make sure that, when looking in the feed direction, the needle ret...
Page 6 - Zeroing the feed motion; Zeroing procedure with the gearbox closed
PFAFF 5 2 Zeroing the feed motion Requirement The feed dog must not move when turning the handwheel with the stitch length set at “0”. 2.1 Zeroing procedure with the gearbox closed ● Raise the presser foot and set the stitch length control lever 1 at its lowest position. ● Turn eccentric bushing 2 (...
Page 7 - Zeroing procedure with the gearbox open
6 PFAFF 2.2 Zeroing procedure with the gearbox open ● Raise the presser foot and set the stitch length control lever 1 at its lowest position. ● Turn eccentric bushing 2 (screw 3 ) so that mark 4 is roughly at the bottom and the edge of the milled surface is at an angle of 45° to the machine front (...
Page 8 - PFAFF 7; Zeroing the needle feed motion; the handwheel is turned.
PFAFF 7 3 Zeroing the needle feed motion (Adjustment not applicable to Pfaff 483) Requirement: With the stitch length control set at “0” the needle bar should make no feed motion when the handwheel is turned. ● Adjust needle feed regulating crank 1 (screw 2 ) according to the requirement. Adjustment...
Page 9 - Feed lifting motion
8 PFAFF 4 Feed lifting motion Requirement With the stitch length set at “0” the feed dog should be at t.d.c. when the needle bar is at a position 0.6 mm past b.d.c (cylindrical pin in hole “3”; for PFAFF 481 ) or 0.6 mm past t.d.c (cylindrical pin in hole “1”; for PFAFF 483 ). In this position, the ...
Page 10 - Feed dog height
PFAFF 9 5 Feed dog height Requirement With the stitch length set at “0” and the needle bar at a position 0.6 mm past b.d.c (cylindrical pin in hole “3”, for PFAFF 481 ) and 0.6 past t.d.c. (cylindrical pin in hole “1”; for PFAFF 483 ) 1. the feed dog must be positioned in the middle of the needle pl...
Page 11 - Feed driving motion
10 PFAFF 6 Feed driving motion Requirement With the longest stitch length set and the needle bar at 0.6 mm past b.d.c. (cylindrical pin in hole “3”; for PFAFF 481 ) the needle bar at 0.6 mm past t.d.c. (cylindrical pin in hole “1”; for PFAFF 483 ) the feed dog should not move when the reverse-feed c...
Page 12 - Timing the needle feed motion
PFAFF 11 7 Timing the needle feed motion (Adjustment not applicable to PFAFF 483) Requirement Both the needle bar and the feed dog should remain motionless when reverse-feed control 3 is moved up and down with the machine set for its longest stitch and the needle bar set 0.6 mm past its b.d.c. (cyli...
Page 13 - Centering the needle in the needle hole
12 PFAFF ● Set the stitch length at “0” and position the needle right above the needle hole. ● Loosen screws 1 and 2 . ● Position needle bar frame 3 both lengthwise and crosswise of the sewing direction according to the requirement and tighten screw 1 . ● Turn the handwheel a few turns to ensure tha...
Page 15 - Eccentric hook shaft bearing and hook-to-needle clearance
14 PFAFF 9 Eccentric hook shaft bearing and hook-to-needle clearance ● Loosen screws 1 and 2 . ● Turn bearing 3 according to requirement 1. ● Set the hook lightly against spin disc 4 , shift bearing 3 - without turning it - according to requirement 2 and tighten screws 1 and 2 . ● Position gear 5 (s...
Page 17 - Vertical position of bobbin case opener
16 PFAFF 11 Vertical position of bobbin case opener Requirement 1. Small hook (481 and 483) At the left point of reversal of bobbin case opener 3 the bobbin case opener finger must be roughly on one level with the lug of bobbin case base 4 . 2. Large hook (481G and 483G) At the left point of reversa...
Page 18 - Position of bobbin case opener
PFAFF 17 12 Position of bobbin case opener Requirement 1. Small hook (481 and 483) With bobbin case opener 3 in its left point of reversal there must be a clearance of approx. 0.8 mm between the front edge of the bobbin case opener finger and the edge of bobbin case base 6 . 2. Large hook (481 and 4...
Page 19 - Timing the bobbin case opener
18 PFAFF 13 Timing the bobbin case opener Requirement In needle bar position 1.8 mm past b.d.c. (cylindrical pin in hole “4”) bobbin case opener finger must be at its right point of reversal. ● Adjust bobbin case opener eccentric 1 (screws 2 ) according to the requirement. Adjustment aid: To facilit...
Page 20 - Clearance between presser foot and needle plate
PFAFF 19 14 Clearance between presser foot and needle plate Requirement With presser bar lifter 1 raised there must be a clearance of 5 mm between presser foot and needle plate. Note: When the presser foot is raised to its top position upon actuating the knee lever fully or by means of the automatic...
Page 21 - Eliminating feed differences
20 PFAFF 15 Eliminating feed differences (Adjustment not applicable to PFAFF 483) Requirement With the machine set for its longest stitch, both the feed dog and and the needle must make feed strokes of the same length when the handwheel is turned. ● Shift hinge stud 1 (nut 2 ) to adjust the feed str...
Page 22 - Tension release mechanism
PFAFF 21 16 Tension release mechanism Requirement When presser bar lifter 1 is raised both tension discs must be at least 0.5 mm apart. ● Adjust tension release lever 2 (screw 3 ) according to the requirement. ● Lower the presser foot onto the needle plate. Now the tension must be fully activated. 0...
Page 23 - Thread check spring and thread regulator
22 PFAFF 17 Thread check spring and thread regulator Requirement 1. Thread check spring 3 must have moved by its full stroke by the time the point of the needle enters the material (stroke approx. 7 mm ). 2. Thread regulator 4 must be fixed in the elongated hole so that thread check spring 3 moves b...
Page 24 - Knee lever resting position
PFAFF 23 18 Knee lever resting position Requirement When at rest, knee lever connecting rod 2 must be at right angles with the bedplate. ● Raise the presser foot by means of the presser bar lifter. ● Push the knee lever joint on knee lever shaft 1 and let the connecting rod 2 engage in the joint. ● ...
Page 25 - Knee lever play
24 PFAFF 19 Knee lever play Requirement When the presser foot is resting on the needle plate, there must be a clearance of 1.3 mm between lifting lever 3 and lifting piece 4 . ● Position the needle at its b.d.c. and let the presser foot down on the needle plate. ● Turn crank 1 (screws 2 ) according ...
Page 26 - Adjusting the knee lever motion
PFAFF 25 20 Adjusting the knee lever motion Requirement When the knee lever is pushed by the full amount of its travel, there must be a clearance as indicated in the table below between presser foot and needle plate and the presser bar lifter should drop by its own weight. Version A and subclass -73...
Page 27 - Bobbin winder
26 PFAFF 21 Bobbin winder Requirement When the bobbin winder is engaged, the winder spindle should be driven reliably; when the bobbin winder is disengaged, however, drive wheel 1 must not contact friction wheel 5 . The bobbin winder should stop automatically when the thread wound on the bobbin has ...
Page 28 - Limiting the stitch length
PFAFF 27 22 Limiting the stitch length ● Loosen screw 1 (accessible through the assembly hole) or turn it out according to the limit to be set. ● Set stitch length control lever 2 at the desired maximum stitch length. ● Set limiting angle 3 from above against control lever 2 and fix it (in the desir...
Page 29 - Matching forwards and reverse stitch lengths
28 PFAFF 23 Matching forwards and reverse stitch lengths Requirement When the stitch length is set at “3” the forwards feed must match the reverse feed. ● Turn bush 1 (screw 2 ) in accordance with the requirement. Make sure that the eccentricity of bush 1 points downwards. 1 2
Page 30 - Presser foot pressure
PFAFF 29 ● Turn screw 1 according to the requirement. 1 24 Presser foot pressure Requirement Proper feeding of the material must be ensured even at top sewing speed. There must Contents
Page 31 - Notes
