Paxar Monarch 415 - Manual

4. Plug the power cord into the rewind (Figure 2). Then, plugthe power cord into a grounded electrical outlet. Figure 2 PowerCord PowerSwitch Fuse Holder Monarch 415 Rewind Operator’s Handbook 2

2. Connecting Supplies Rewinding on the Hub 1. Slide the supply guide away from the hub flange and pull itaway from the hub. 2. Print or feed enough supplies from the printer to wraparound the hub one and one half times. 3. Hold the hub flange and twist the hub clockwise until it stops. 4. Thread th...

6. Turn the hub and hub flange at least one full turn counterclockwise to tighten the supply strip. 7. Push the supply guide against the hub then slide it againstthe supply. NOTE: Units with 3" hubs have a flanged disk instead ofa supply guide. Slide this disk over the hub and against thestock/c...

Rewinding on a Paper Core 1. Slide the supply guide away from the hub flange and pull itaway from the hub. 2. Push the paper core on the hub until it is against the hubflange. 3. Hold the hub flange and twist the hub clockwise until the paper core is tight. 4. Tape the supply strip to the paper core...

3. Operating the Rewind Starting 1. Turn the speed control knob (Figure 6) to SLOW . 2. Push the rewind power switch (Figure 7) ON . NOTE: The rewind will star t to turn. When the dancerroller is almost horizontal, the rewind will stop. 3. Start the printer. 4. Adjust the rewind speed to the speed o...

Stopping 1. Stop the printer. 2. Push the rewind power switch OFF . 3. Pull the supply guide away from the hub. 4. Cut the supply at the supply exit of the printer (Figure 8). 5. Tape the end of the supply to the roll on the rewind. 6. Pull the supply guide away from hub. 7. Hold the hub flange and ...

4. Changing Hubs If you change to a different supply, you may need to use adifferent hub. One, three, and four inch diameter hubs (shortand long) are available from Monarch. To change hubs 1. Pull the supply guide away from the hub (Figure 9). 2. Unscrew the hub knob (Figure 10). NOTE: The hub diame...

8. Slide the first core onto the 415 hub until it is against thehub flange. 9. Hold the hub flange and twist the hub clockwise until thepaper core is tight. 10. Position the slot in the hub to the top. 11. Align the leading edge of the first label on the inside stripwith the slot in the hub and tape...

15. Hold the second separator disk with the inside notch up(in line with the core lock) and slide it onto the hub (Figure16). 16. Place the third core over the core lock and slide it onto thehub. Second SeparatorDisk ThirdCore Core Lock Notch inDisk Figure 16 5. Burster Option Setup and Operation 15

Supply Removal 1. Remove the core lock (metal strip). 2. Remove the flanged collar assembly. 3. Remove the outside core and roll of labels. 4. Remove the second separator disk. 5. Remove the middle core and roll of labels. 6. Remove the inside separator disk. 7. Unlock the inside core. 8. Remove the...

6. Specifications and Supplies Specifications Height:Width:Depth: 13.75 inches (349.25 mm)12.50 inches (317.5 mm)11.5 inches (292.10 mm) Weight: 18 lbs. (8.14 kg) Shipping Weight: 20 lbs. (9.05 kg) Power: 115 VAC 60 HZ 30 Watts .3 Amps220/240 50/60 HZ 30 Watts .15 Amps Fuse: 3/8 Amp Temperature: Ope...

Appendix A: Rewind Alignment Location Guide 113580 Location Guide 113576 Location Guide not available Location Guide 113576 Location Guide 113576 Location Guide 113576 L o c a ti on G u id e 11 46 64 23