ParaBody Leg Press 5 - Manual

Page 2 - IMPORTANT SAFETY INFORMATION; TABLE OF CONTENTS

THERE IS A RISK ASSUMED BY INDIVIDUALS WHO USE THIS TYPE OF EQUIPMENT. TO MINIMIZE RISK FOLLOW THESE RULES ! 1. Before using, read all the warnings and instructionson the use of this machine. Use only for intendedexercise. DO NOT modify the machine. 2. Obtain a medical exam before beginning anyexerc...

Page 3 - Tools Required for Assembly; Bolt Length Ruler; IMPORTANT NOTES

Tools Required for Assembly * 3/4” wrench* 9/16” wrench* Ratchet with 3/4” and 9/16” sockets* Adjustable wrench* Tape measure 3 NOTE: BOLT LENGTH IS MEASURED FROM THE UNDERSIDE OF THE HEAD OF THE BOLT. BOLT LENGTH RULER: Bolt Length Ruler 0 1 2 3 4 5 6 1/2 1/2 1/2 1/2 1/2 1/2 BOLT LENGTH IMPORTANT N...

Page 4 - PARTS LIST

4 PARTS LIST PART # ACU04-1444 ACU04-1447 ACU04-1449 ACU04-1445 ACU04-1446 ACU04-1448 ACU02-1298 ACU07-0135 ACUDA1E03830016NB KEY 1 2 3 4 5 6 7 8 9 QTY 1 1 1 1 1 1 1 2 6 PART # ACUDC1250100020B ACUDB2E03811000B ACUDA1E02143413NB ACUDB2E01212000B ACU11-0080 ACU05-0372 ACU06-0437 ACUDACM04006007YB DES...

Page 5 - FIGURE 1

9−1/2" 5 FIGURE 1 STEP 1: • SECURELY assemble the SECOND ARM (5) to the FRAME (1) using one 1/2 X 4-3/4” BOLT (12), one 3/4 X 4” SHAFT (15) and one 1/2” LOCK NUT (13). See FIGURE 1. 0 1 2 3 4 5 6 1/2 1/2 1/2 1/2 1/2 1/2 12 1/2 X 4-3/4” 1 1 3 15 4 5 • SECURELY assemble the MAIN ARM (4) to the FRA...

Page 6 - FIGURE 2

11−1/4" 6 FIGURE 2 STEP 2: • SECURELY assemble the SECOND ARM (5) to the FRAME (1) using one 1/2 X 4-3/4” BOLT (12), one 3/4 X 4” SHAFT (15) and one 1/2” LOCK NUT (13). See FIGURE 2. • SECURELY assemble the MAIN ARM (4) to the FRAME (1) using one 1/2 X 4-3/4” BOLT (12), one 3/4 X 4” SHAFT (15) a...

Page 7 - FIGURE 3

FIGURE 3 STEP 3: 7 • Insert one 3/4 X 4” SHAFT (15) thru pre-installed FLANGE BEARINGS in the SECOND ARM (5) as shown in FIGURE 3. • Insert one 3/4 X 4” SHAFT (15) thru pre-installed FLANGE BEARINGS in the MAIN ARM (4) as shown in FIGURE 3. 4 5 0 1 2 3 4 5 6 1/2 1/2 1/2 1/2 1/2 1/2 15

Page 8 - FIGURE 4

8 STEP 4: FIGURE 4 • SECURELY assemble the FOOTPLATE (6) to the SECOND ARM (5) and the MAIN ARM (4) using two 1/2 X 4-3/4” BOLTS (12) and two 1/2” LOCK NUTS (13). See FIGURE 4. 12 1/2 X 4-3/4” 6 5 1 3 4

Page 9 - FIGURE 5

9 STEP 5: FIGURE 5 3/8 X 3” 9 1 11 1 0 3 • SECURELY assemble the HANDLE (3) to the FRAME (1) using two 3/8 X 3” BOLTS (9), four 3/8” FLAT WASHERS (10) and two 3/ 8” LOCK NUTS (11) as shown in FIGURE 5. 0 1 2 3 4 5 6 1/2 1/2 1/2 1/2 1/2 1/2

Page 10 - FIGURE 6

1 0 STEP 6: FIGURE 6 • CAREFULLEY slide the SEAT ADJUST (2) into the FRAME (1) as shown. The SEAT can be adjusted by turning the SPRING PIN KNOB (14) clockwise and pulling. The SEAT can be secured in place by releasing the pin into an adjustment hole and turningclockwise until tight. 1 2 14 17 • Sec...

Page 11 - FIGURE 7

STEP 7: FIGURE 7 • SECURELY assemble one PAD (8) to the SEAT ADJUST (2) using two 3/8 X 3” BOLTS (9) and two 3/8” FLAT WASHERS (10) as shown in FIGURE 7. 9 3/8 X 3” 1 0 2 8 11 0 1 2 3 4 5 6 1/2 1/2 1/2 1/2 1/2 1/2

Page 12 - FIGURE 8

1 2 STEP 8: FIGURE 8 • SECURELY assemble one PAD (8) to the FRAME (1) using two 3/8 X 3” BOLTS (9) and two 3/8” FLAT WASHERS (10) as shown in FIGURE 8. 3/8 X 3” 9 1 1 0 8 Thank you for purchasing the Parabody LP5 LEG PRESS. If unsure of proper use of equipment, call your local Parabody distributor o...

Page 14 - LIMITED WARRANTY

1 4 NOTES: LIMITED WARRANTY ParaBody extends the following LIMITED WARRANTY to the original owner of the ParaBody products. The Warranty terms apply to IN HOME USE ONLY. 1. LIMITED WARRANTY ON FRAME AND WELDS. If the frame of the ParaBody product or a weld should crack or break, it will be repaired ...

ParaBody Leg Press 5 - Manual

Table of Contents:

Summary

Other ParaBody Models