ParaBody 832102 - Manual - manualsarea.com

Page 2 - BOLT LENGTH RULER:; Bolt Length Ruler; WELCOME TO THE WORLD OF; BOLT LENGTH; Consult a physician before beginning any exercise program.

IMPORTANT NOTES Please note: Tools Required for Assembly * Thank you for purchasing the Parabody 832102 LEG PRESS. Please read these instructions thoroughly and keep them for future reference. This product must be assembled on a flat,level surface to assure its proper function. * 3/4” wrench* 9/16” ...

Page 3 - PARTS LIST

3 PARTS LIST PART # 6 5 7 4 5 0 3 6 5 7 3 6 0 3 6 6 5 5 7 0 1 6 5 7 5 4 0 3 6 5 7 3 9 0 3 6 4 7 6 4 0 3 6 5 7 5 1 0 2 6 5 9 7 4 0 2 6 5 7 4 0 0 1 3 1 0 3 1 0 2 311 6 2 0 1 6 1 7 7 0 0 1 6 4 0 5 2 0 1 6 4 1 6 6 0 1 6 4 6 7 0 0 1 6 5 0 0 6 0 1 3 1 0 2 5 0 1 KEY 1 2 3 4 5 6 7 8 9 1 0 11 1 2 1 3 1 4 1 5...

Page 4 - FIGURE 1

4 FIGURE 1 STEP 1: • SECURELY assemble the REAR TUBE (3) to the BASE FRAME (1) using two 3/8 X 3” BOLTS (25), four 3/8” FLAT WASHERS (17), and two 3/8” LOCK NUTS (19). See FIGURE 1. 0 1 2 3 4 5 6 1/2 1/2 1/2 1/2 1/2 1/2 • Attach two 2” SQ. COVER CAPS (15) onto the ends of the REAR TUBE (3) as shown ...

Page 5 - FIGURE 2

FIGURE 2 STEP 2: • SECURELY assemble one 3/8” SPRING PIN (33) to the spring pin barrel on the SEAT FRAME (2) as shown in FIGURE 2. • Insert two 2” SQ. ENDCAPS (13) into the ends of the SEAT FRAME (2) as shown in FIGURE 2. 2 13 33 14 • Attach four PARAGLIDE STRIPS (14) to the inside of the SEAT FRAME...

Page 6 - FIGURE 3

6 STEP 3: FIGURE 3 0 1 2 3 4 5 6 1/2 1/2 1/2 1/2 1/2 1/2 • Attach four PARAGLIDE STRIPS (14) to the outside of the ADJUSTMENT TUBE (7) using the following steps: • Thoroughly clean all surfaces where the PARAGLIDE STRIPS (14) are to be attached. • Remove the PARAGLIDE STRIPS (14) from the paper back...

Page 7 - FIGURE 4; FIGURE 5

7 STEP 4: FIGURE 4 • CAREFULLEY slide the ADJUSTMENT TUBE (7) over into the SEAT FRAME (2) and engage the SPRING PIN into one of the adjustment holes. See FIGURE 4. 7 2 SPRING PIN FIGURE 5 STEP 5: • Insert two 3/4” FLANGE BEARINGS (31) into each of the two LEVER TUBES (5) asshown in FIGURE 5. 31 5 3...

Page 8 - FIGURE 6

8 STEP 6: FIGURE 6 17 5 5/16” SET SCREW 32 0 1 2 3 4 5 6 1/2 1/2 1/2 1/2 1/2 1/2 1 9 • SECURELY assemble the LEVER TUBES (5) to the BASE FRAME (1) using two 3/4” SHAFTS (9) and SECURE in place using four 5/16” SET SCREWS (32). See FIGURE 6. • Insert four 2” SQ. END CAPS (13) into the ends of two LEV...

Page 9 - FIGURE 7

9 STEP 7: FIGURE 7 1 30 5 4 13 • Insert four 2” SQ. END CAPS (13) into the ends of FOOT PLATE (4) as shown in FIGURE 7. • Insert eight 1/2” FLANGE BEARING (30) into the LEVER TUBES (5) as shown in FIGURE 7.

Page 10 - FIGURE 8

10 FIGURE 8 STEP 8: • SECURELY assemble the FOOT PLATE (4) to the LEVER TUBES (5) using two 1/2 X 6-1/2” BOLTS (28) and two 1/2” LOW HEIGHT LOCK NUTS (22) as shown in FIGURE 8. 0 1 2 3 4 5 6 1/2 1/2 1/2 1/2 1/2 1/2 1/2” LOW HEIGHT 22 28 1/2 X 6-1/2” 5 12 4 • CAREFULLY attach eight NON-SKID STRIPS (1...

Page 11 - FIGURE 9

FIGURE 9 STEP 9: 11 27 1/2 X 3-1/4” 2 21 5 • SECURELY assemble the SEAT FRAME (2) to the LEVER TUBES (5) using two 1/2 X 3-1/4” BOLTS (27) and two 1/2” LOCK NUTS (21) as shown in FIGURE 9.

ParaBody 832102 - Manual

Table of Contents:

Summary

Other ParaBody Models