Page 2 - CAUTION
2 The serial number of this product may be found on the bot-tom of the unit.You should note the serial number of this unit in the spaceprovided and retain this book as a permanent record of yourpurchase to aid identification in the event of theft. Model No. Serial No. WARNING: To reduce the risk of ...
Page 3 - CONTENTS; ENGLISH
3 CONTENTS PREFACE .................................................................................................................................................................................... 4FEATURES .............................................................................................
Page 5 - PRECAUTIONS
5 • Refer all work related to the installation of this product to qualified service personnel or systeminstallers. • Do not block the ventilation opening or slots on the cover. To prevent the appliance temperature from rising, placethe appliance at least 5 cm (2 inches) away from thewall. • Do not d...
Page 6 - MAJOR OPERATING CONTROLS AND THEIR FUNCTIONS; Front View
6 MAJOR OPERATING CONTROLS AND THEIR FUNCTIONS t 1 POWER CAMERA SELECT SET ON OFF Video Multiplexer WJ-FS SWITCH PROTECTER 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 STILL MENU ESC EL-ZOOM F S 316 VCRCAM SPOT SEQ MULTISCREEN MULTI SCREEN SELECT ALARMRESET ALARM 1 POWER CAMERA SELECT SET ON OFF Video Multi...
Page 8 - Rear View
8 SIGNAL GND ALARM/REMOTE OUT IN VIDEO 16 15 14 13 12 11 10 9 8 16 15 14 13 12 11 10 9 8 7 6 5 4 2 1 7 6 5 4 3 3 2 1 PLAY IN REC OUT SPOT OUT DATA CAMERA SW IN MULTISCREEN OUT i o u !1 !0 q Video Input Connectors (VIDEO IN) These connectors accept a composite video signalfrom a camera. Note: If the ...
Page 9 - SETUP MENU; Displaying the SETUP MENU
9 SETUP MENU In the SETUP MENU you can set preferences for ALARM,MONITOR, REC OUT, SEQUENCE and SYSTEM to meetyour requirements. ● Displaying the SETUP MENU 1. Confirm that the camera and peripherals are connected correctly and securely. 2. Turn on the power switches of all system components.3. Pres...
Page 10 - Setup Menu
10 SETUP MENU ALARM SETUP(Alarm Setup) Page 11 MULTI OUTPUT TITLE DISP (Camera Title Display)STILL DISP (Still Display)BORDER (Border Display)QUAD SHIFT (Quad Shift)SECRET VIEW BAUD RATEDATA BIT TITLE DISP TITLE DISPLAY (Record Title Display)REC MODE (Recording Mode) SPOT OUTPUT TITLE SETUP (Camera ...
Page 11 - Alarm Setup Menu
11 1. Move the cursor on GROUP in the DYNAMIC REC line and press the SET button to open the GROUP SETUP menu shown above. 2. Move the cursor to the desired position by pressing the C , D , A , B buttons. Note: To turn over the page for WJ-FS316/FS416, keep the cursor moving up or down. 3. Select the...
Page 13 - Monitor Output Setup Menu
13 9. MLT OUT MODE This item lets you select whether to switch the multiscreenoutput monitor screen automatically to the camera pictureof the channel whose alarm is activated. 1. Move the cursor to the MLT OUT MODE parameter.2. Select OFF or SPOT by pressing the + or – button. The initial factory se...
Page 14 - Record Output Setup Menu
14 1. TITLE DISPLAY This item lets you enable or disable recording of the cam-era title with the picture. 1. Move the cursor to the TITLE DISPLAY parameter.2. Select either ON or OFF. The initial factory setting is ON. ON: Enables recording of the camera title with the pic- ture on the tape. OFF: Di...
Page 15 - Sequence Setup Menu
15 2. REC MODE This item lets you select the time interval (field rate) forswitching the camera channel of the REC OUT signal.When REC MODE is set to EXT, the timing is controlled bythe connected VCR. When 004-255 (INT) is selected, thetiming corresponds to the field rate set here.The parameter sett...
Page 16 - Step Assignment
16 QUAD SEQ SETUP STEP CH SEC STEP CH SEC 1 4A 2S 9 -- 0S 2 4B 2S 10 -- 0S 3 4C 2S 11 -- 0S 4 4D 2S 12 -- 0S 5 -- 0S 13 -- 0S 6 -- 0S 14 -- 0S 7 -- 0S 15 -- 0S 8 -- 0S 16 -- 0S QUAD SEQ SETUP STEP CH SEC STEP CH SEC 1 4A 2S 9 -- 0S 2 4B 2S 10 -- 0S 3 9 2S 11 -- 0S 4 -- 0S 12 -- 0S 5 -- 0S 13 -- 0S 6...
Page 17 - System Setup Menu
17 2. SPOT OUTPUT 2-1. AUTO SKIP This item lets you enable or disable the Auto Skip functionto skip any steps where no video signal is present at theSpot output.Proceed as described in MULTI OUTPUT, 1.1 AUTO SKIPon page 15. 3. MLT/SPT SEQ SETUP This item lets you program or edit a Multi or a SpotSeq...
Page 22 - Mounting in the Rack; INSTALLATIONS
22 ■ Mounting in the Rack 1. Remove the four rubber feet by removing the four screws on the bottom of the video multiplexer. 2. Place the rack mounting brackets on both sides of the video multiplexer and tighten with the six suppliedscrews (M3 x10). 3. Install the video multiplexer with the rack mou...
Page 23 - Basic System Connection; SYSTEM CONNECTIONS
23 ■ Basic System Connection The Video Multiplexers WJ-FS309, WJ-FS316, WJ-FS409 and WJ-FS416 are connected with cameras, video monitors and aTime Lapse VCR. A typical connection example is shown below. The ALARM/REMOTE connector is described later. • The figure shows the WJ-FS309/FS409. The WJ-FS31...
Page 24 - Connection with the Time Lapse VCR
24 ■ Connection with the Time Lapse VCR Connect the time lapse VCR as shown in the example below. 2 4 6 8 10 12 14 16 ALARM IN 1 COM 2 ALARM RESET IN 3 ALARM RECOVER OUT 4 ALARM OUT 5 1 SHOT IN 6 7 TAPE END OUT 8 WARNING OUT 9 HUMID OUT 10 REC OUT 11 REC REVIEW OUT 12 SERIES REC IN 13 14 TIME ADJUST...
Page 26 - Setting the System Controller; Connection with the Monitors; Termination for RS-485 chain
26 ■ Connection with the WV-CU360System Controller ● Basic Connection Connect the DATA jack on the Video Multiplexer to the DATA OUT jack on the System Controller with the sup-plied RS-485 cable (part of standard accessories of theSystem Controller). ● Loop-through Connection 1. Plug the branch cabl...
Page 27 - ALARM/REMOTE Connector
27 ■ ALARM/REMOTE Connector This 25-pin connector connects alarm related control sig-nals and/or remote switch inputs depending on the statusof pins #5 and #22. The tables below show the pin assign-ment for the WJ-FS309/FS409 and WJ-FS316/FS416,respectively. 13 1 25 14 For WJ-FS316/FS416 Pin # Pin N...
Page 29 - Connection with the Remote (External) Switches; Remote SW1
29 22 5 5 4 3 2 1 Switch SEQUENCE MENU SPOT VCR/CAM ZOOM STILL MULTI SCREEN Function 1 GND GND GND Function 2 GND GND 15 22 5 16 14 13 12 11 10 9 8 7 6 5 4 3 2 1 Switch Camera Selection SEQUENCE Function 1 GND GND GND GND Openor +5V Function 2 ■ Connection with the Remote (External) Switches The Vid...
Page 30 - OPERATING PROCEDURES; Monitoring the Camera Picture; SPOT OUT
30 OPERATING PROCEDURES ENTRANCE Camera 3 Picture Camera 6 Picture Example of spot camera picture sequence SEQ ■ Monitoring the Camera Picture ● SPOT OUT 1. Spot Picture 1. Press a SPOT/MULTISCREEN button so that the LED of SPOT/MULTISCREEN button lights up. 2. Spot Sequence 1. Press the SEQ button....
Page 31 - MULTISCREEN OUT
31 VCR CAM ENTRANCE Camera 3 Picture Camera 6 Picture Example of spot camera picture sequence SEQ ● MULTISCREEN OUT 1. Spot Picture 1. Press a SPOT/MULTISCREEN button so that the LED of SPOT/MULTISCREEN button goes off. 2. Spot Sequence 1. Press the SEQ button. A sequence of single pictures is displ...
Page 32 - Zoomed Spot Picture; Still Spot Picture
32 4. Zoomed Spot Picture The following function is available in MULTISCREENOUT picture only. 1. Repeat the procedures described above for Spot Picture. 2. Press the EL-ZOOM button to display the zoomed pic- ture. The “+” sign appears in the picture. Note: The “+” sign disappears if no operation is ...
Page 33 - Still Multiscreen Picture; Multiscreen Picture; Multiscreen Sequence
33 3. Press the MULTISCREEN SELECT button to select multiscreen pattern (4-, 9- or 16-segment screen). Note: 16-segment screen is not available for WJ- FS309/FS409. 4. Each time the MULTISCREEN SELECT button is pressed, the multiscreen changes as follows: WJ-FS309/FS409: 4 → 9 → 4 screen segments WJ...
Page 34 - Spot Playback Picture
34 ■ Recording on the Time Lapse VCR Confirm the parameters on the REC OUTPUT SETUP menu.See page 14 for details. Note: When EXT is selected but no camera switching sig- nal is supplied, time lapse recording will not work prop-erly. In this case, supply the camera switching signal orset REC MODE to ...
Page 35 - Zoomed Spot Playback Picture; Still Spot Playback Picture
35 3. Zoomed Spot Playback Picture 1. Repeat the procedures described above for Spot Playback Picture. 2. Press the EL-ZOOM button to display the zoomed pic- ture. The “+” sign appears in the picture. Note: The “+” sign disappears if no operation is per- formed within approx. 5 seconds. If the “+” s...
Page 36 - Multiscreen Playback Picture; Still Multiscreen Playback Picture; Playback Multiscreen Sequence
36 4. Multiscreen Playback Picture 1. Operate the VCR in playback mode.2. Confirm that the LED on the VCR/CAM button is lit. If the LED is not lit, press the VCR/CAM button so that the LED on the VCR/CAM button lights. 3. Press the SPOT/MULTISCREEN button so that the LED of SPOT/MULTISCREEN button g...
Page 37 - Alarm Input; Alarm Operation; Front Panel Display; Record Output; Alarm Priority Mode; Spot Output; Alarm Channel Monitor Mode; Multiscreen Output; Alarm Display Mode; ALARM CONTROL FUNCTION
37 ■ Alarm Input The Video Multiplexer can handle the following alarms: • Interface Alarm Alarm received from the ALARM/REMOTE connector.“ALARM” is displayed on the monitor screen. • Camera Switching Signal Loss Alarm Alarm indicating that camera switching signal loss hasoccurred.“SW LOSS” is displa...
Page 38 - Auto Reset; External Reset; Alarm Reset; Manual Reset
38 ● Auto Reset The alarm is automatically reset after the programmedAlarm Output Time has elapsed.The ALARM indicator changes from blinking to steady light.Pressing the ALARM RESET button will clear the alarm and make the indicator go off. ● External Reset The alarm is reset by a recovery signal re...
Page 39 - OTHER FUNCTIONS; ALL RESET; Channel Loss Alarm; OPERATING CONTROL OF SYSTEM UNITS (Supplementary)
39 ■ Camera Switching Pulse LossDisplay • When loss of the camera switching pulse is detected, “SW LOSS” will blink on the monitor screen. • The buzzer does not beep.• When the camera switching pulse is recovered, “SW LOSS” is cleared from the monitor. OTHER FUNCTIONS The Video Multiplexer WJ-FS309/...
Page 40 - APPENDIX; Communication Protocol; Command Table
40 Data format Format (Send 1) 5 channel: Alarm mode [sfx]ADOOA; ALM:[OF][OF][OF] [OF][B7][OF][efx] (Response) None5ch: Alarm mode b 1 b 2 b 3 a 1 a 2 a 3 a 4 0Fh 0Fh 0Fh 0Fh 87h 0Fh 0Fh 5ch, 15ch, 16ch: Alarm mode b 1 b 2 b 3 a 1 a 2 a 3 a 4 0Fh 0Fh 0Fh 0Fh 87h 0Fh 3ch 17ch: Alarm mode b 1 b 2 b 3 ...
