Oster 10 - 76010 - Manual

Heavy-Duty Detachable

Blade Clipper

Instruction Manual

•

For Commercial Use Only

•

Model 10 - 76010

AVAILABLE OSTER

®

LUBRICANTS & CLEANERS,

& REPLACEMENT PARTS

Regular use of the following products will help you enjoy optimum performance from your
clipper and prolong its functionality.

Oster 5-in-1

®

(076300-107)

All-purpose clipper

& blade lubricant

and disinfectant.

Kool Lube

®

3

76300-101

Lubricates and

cools down blade.

Spray
Disinfectant
76300-102

Minimizes bacteria

buildup between

upper and lower

blades.

Blade Wash

®

Cleaning
Solution 76300-
103

Flushes away

accumulated hair

and removes dirt

buildup trapped

between upper

and lower cutting

blades.

Blade Lube™
Oil 76300-104

Lubricates between

upper and lower

blades to keep

them sharper lon-

ger and produce a

smoother clipping

action

Gear Lube

®

(076300-105)

Specially designed

to prolong the life of

gears, bearings and

the motor.

Replacement carbon brushes
(076917-710)

Set of replacement carbon brushes and

springs

To order any of these products, please call 1-800-830-3678 or visit www.osterstyle.com

IMPORTANT SAFEGUARDS

Commercial Clipper • When using an electrical appliance, basic precautions

should always be followed, including the following:

Read all instructions before using this appliance.

DANGER

To reduce the risk of electric shock:

1. Do not reach for an appliance that has

fallen into water. Unplug immediately.

2. Do not use while bathing or in a

shower.

3. Do not place or store appliance where

it can fall or be pulled into a tub or

sink.

4. Do not place in or drop into water

or other liquid.

5. Always unplug this appliance from

the electrical outlet immediately after

using.

6. Unplug this appliance before cleaning,

putting on or taking off parts.

WARNING

To reduce the risk of burns, fire,

electric shock, or injury to persons:

1. An appliance should never be left

unattended when it is plugged in.

2. Close supervision is necessary when

this appliance is used by, on, or near

children or invalids.

3. Use this appliance only for its intended

use as described in this manual. Do not

use attachments not recommended by

the manufacturer.

4. Never operate this appliance if it has

a damaged cord or plug, if it is not

working properly, if it has been dropped

or damaged, or dropped into water.

Return the appliance to a service center

for examination and repair.

5. Keep cord away from heated surfaces.

6. Never operate the appliance when air

openings are blocked or while on a soft

surface (such as a bed or couch).

7. Never drop or insert any object into

opening.

8. Do not use outdoors or operate where

aerosol spray products are being used

or where oxygen is being administered.

9. Do not use this appliance with a

damaged or broken comb or blade,

as cut or scratched skin may occur.

10. To disconnect, move all controls to

“OFF”, then remove plug from outlet.

11. Do not wrap cord around unit when

storing. Continuous stress on the

cord can damage cord insulation and

result in a shock hazard.

12. Avoid contact with moving blades.

13. Avoid tangling or kinking the cord

while clipping. Should the cord become

tangled or kinked, stop clipping and

straighten the cord.

SAVE THESE INSTRUCTIONS

THE FOLLOWING PARAGRAPH IS FOR 120-VOLT MARKETS ONLY

To reduce the risk of electrical shock, this appliance has a polarized plug

(one blade is wider than the other). This plug fits a polarized outlet only one

way. This is a safety feature intended to help reduce the risk of electrical

shock. If the plug does not fit fully into the outlet, reverse the plug. If it still

does not fit, contact a qualified electrician. Do not attempt to defeat this

safety feature.

ABOUT YOUR CLIPPER

Although your clipper has been thoroughly tested and inspected at every

stage of its manufacturing and assembly, it is recommended that you lubri-

cate it, as instructed in this manual, after 4-6 weeks of extensive use. This

will ensure you obtain optimum performance and prolong the life of your

clipper.

GETTING FAMILIAR WITH

YOUR CLIPPER

Due to continuous product improvement, product may vary slightly from
what is illustrated.

11

12

13

1

2

5

6

8

9

10

6

3/4

7

6

4

USING YOUR CLIPPER

Important:
• Before using your clipper, apply 1 or 2 drops of Oster

®

Clipper & Blade

Lube™ Oil to the blade (refer to Taking Care of Your Clipper section).

• For best results, hair should be clean and free from styling agents.
• During use, apply Kool Lube

®

coolant occasionally to the blades to keep

them cool.

1. Plug unit into an AC electrical outlet.

2. Move On/Off switch to turn clipper on.

3. Remove blade guard.

4. Insert blade. Holding blade sides, slide blade bracket into hinge.

5. Push blade toward the clipper until it snaps into place

6. When finished clipping, turn clipper off and unplug cord from electrical outlet.

7. Cover blade with blade guard to keep it protected.

Note: Any other maintenance not explained in this manual must be per-

formed by an Oster-Direct

®

Authorized Service Center.

Important: Make sure clipper is turned off and unplugged from electrical

outlet before removing, replacing or cleaning any parts.

Lubricating Motor
If you hear a “squeal” or a dry bearing noise

from the motor, it is a signal that the motor

needs lubricating.
Remove cap from Oster

®

Clipper and Blade

Lube™ tube and insert tip into oiler to apply 1

drop of oil. Be careful not to over lubricate.
Greasing Gear Drive Assembly
We recommend checking the gear drive

assembly every six months for greasing.
Caution: Grease only when necessary as over-greasing may cause

leakage and reduce clipper’s efficiency.

STEP 4

STEP 5

TAKING CARE OF YOUR CLIPPER

APPLY 1

DROP

1. Blade guard

2. Blade

3. Blade bracket

4. Blade hinge

5. Name plate/gear drive assembly access

6. Carbon brush cap/carbon brush

7. Oiler

8. Power cord

9. On/Off switch

10. Hanging ring

11. Cleaning Brush

12. Oster

®

Clipper & Blade Lube™ oil

13. Oster Gear Lube

®

grease

10-76010_12EM1.indd 1

8/7/12 11:03 AM