Onkyo CR-305X - Manual
Onkyo CR-305X – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.
Table of Contents:
- Page 2 – CAUTION ON REPLACEMENT OF OPTICAL PICKUP; PRECAUTIONS; Grounding for the test equipments and tools.; SPECIFICATIONS; AMPLIFIER; CD PLAYER
- Page 3 – PROTECTION OF EYES FROM LASER BEAM DURING SERVICING; Laser Diode Properties; Emission Duration: continuous; LASER WARNING LABEL; The label shown below are affixed.
- Page 4 – SERVICE PROCEDURE; Replacing the fuses; DESCRIPTION; To initialize the unit; Memory Preservation; Front
- Page 5 – DISPLAY; FRONT PANEL VIEW
- Page 6 – Asian and European models; REAR PANEL VIEW
- Page 8 – MICROPROCESSOR CONNECTION DIAGRAM; MICROPROCESSOR
- Page 9 – MICROPROCESSOR TERMINAL DESCRIPTION
- Page 10 – IC BLOCK DIAGRAM AND DESCRIPTIONS; Block Diagram
- Page 11 – Terminal description
- Page 12 – Bloch Diagram
- Page 15 – Comparator; VREF
- Page 16 – GND; Truth table; rr
- Page 17 – pickup drive unit
- Page 18 – screw
- Page 19 – CHASSIS EXPLODED VIEW
- Page 21 – PRINTED CIRCUIT BOARD VIEW PARTS LIST
- Page 23 – PRINTED CIRCUIT BOARD VIEW 1
- Page 25 – PRINTED CIRCUIT BOARD VIEW 2; Component side
- Page 26 – PRINTED CIRCUIT BOARD VIEW 3
- Page 27 – Preparation; Set the trimming resistors R123 to center.; Focus gain adjustment; Set the output of the audio oscillator to 1 kHz and 1; Trimming resistor R123; RF; Test point; * The adjustment of focus offset adjustment is unnecessary.; reqency counter; Trimmer capacitor C703; Display
- Page 28 – ASSEMBLING OF PAD; Pad; Pin mark; Side view; PACKING VIEW PARTS LIST; PACKING VIEW
CD RECEIVER
MODEL CR-305X
Ref.NO.3654
082000
TABLE OF CONTENTS
CR-305X
Specifications -----------------------------------------------------------
Caution on replacement of optical pickup --------------------------
Protection of eyes from laser bam during servicing ---------------
Service procedures -----------------------------------------------------
Front panel view ------------------------------------------------------
Rear panel view -------------------------------------------------------
Remote controller ----------------------------------------------------
Microprocessor connection diagram --------------------------------
Microprocessor terminal descriptions ------------------------------
IC Block diagram and descriptions ---------------------------------
CD Mechanism exploded view --------------------------------------
Replacement of optical pickup ---------------------------------------
Chassis exploded view parts list -------------------------------------
Chassis exploded view -----------------------------------------------
Block diagram ---------------------------------------------------------
Wiring view ------------------------------------------------------------
Printed circuit board view parts list --------------------------------7
Schematic diagram (Amplifier section) -----------------------------
Printed circuit board view 1-------------------------------------------
Schematic diagram (CD & Microprocessor section) -------------
Printed circuit board view 2-------------------------------------------
Printed circuit board view 3-------------------------------------------
CD Adjustment procedures ------------------------------------------
Clock adjustment procedures ----------------------------------------
Assembling of pad ---------------------------------------------------
packing view ---------------------------------------------------------
10
19
21
22
23
25
26
27
29
31
33
35
37
39
40
41
42
Silver models
120 V AC,60 Hz
230 V AC,50 Hz
220 - 230 V AC,50/60Hz
UDD,UDT
UPP
UGT,UGR
SAFETY-RELATED COMPONENT WARNING!!
COMPONENTS IDENTIFIED BY MARK ON THE
SCHEMATIC DIAGRAM AND IN THE PARTS LIST
ARE CRITICAL FOR RISK OF FIRE AND ELEC-
TRIC SHOCK. REPLACE THESE COMPONENTS
WITH ONKYO PARTS WHOSE PARTS NUMBERS
APPEAR AS SHOWN IN THIS MANUAL.
MAKE LEAKAGE-CURRENT OR RESISTANCE
MEASUREMENTS TO DETERMINE THAT EXPO-
SED PARTS ARE ACCEPTABLY INSULATED FORM
THE SUPPLY CIRCUIT BEFORE RETURNING THE
APPLIANCE TO THE CUSTOMER.
"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.
Summary
− 1 − CR-305X CAUTION ON REPLACEMENT OF OPTICAL PICKUP The laser diode in the optical pickup block is so sensitive tostatic electricity, surge current and etc., that the componentsare liable to be broken down or its reliability remarkably deteriorated. During repair,carefully take the following p...
PROTECTION OF EYES FROM LASER BEAM DURING SERVICING This set employs a laser. Therefore, be sure to follow carefully the instructions below when servicing. WARNING!! SERVICE WARNING : DO NOT APPROACH THE LASER EXIT WITH THE EYE TOO CLOSELY. IN CASE IT IS NECESSARY TO CONFIRM LASER BEAM EMISSION, BE ...
SERVICE PROCEDURE 1. Replacing the fuses 3. Safety-check out (Only U.S.A. model)After correcting the original service problem perform thefollwing safety check before releasing the set to the customerConnect the insulating-resistance tester between the plug ofpower supply cord and terminal GND on the...