Oliveri PE341 - User Manual

INSTALLER - PLEASE READ & FOLLOW THESE

INSTALLATION INSTRUCTIONS

Please retain for owner as care instructions are included.

FOR TOPMOUNT OR ‘DROP-IN’ SINKS

CHECK MODEL

The model number on the sink

packaging must match the model

of sink the customer ordered.

Do not install if incorrect.

AVOID CUTS

The perimeter and punch-outs on

the sink may contain sharp edges.

Handle the sink carefully to avoid

personal injury.

TF08g - Topmount Installation and Care Instructions

Oliveri Solutions Pty Ltd

51 Naweena Rd, Regency Park SA 5010 Phone: +61 8 8348 6444 Email: [email protected]

oliveri.com.au

CARE INSTRUCTIONS FOR YOUR OLIVERI STAINLESS STEEL SINK

AVOID CONTACT WITH ROUGH OR DIRTY SURFACES.

Manufactured from genuine 18/10, 304-grade stainless steel, Oliveri stainless steel sinks offer
optimum hygiene and durability. Your sink will continue to shine for many years with regular care.

• Clean daily with soap and water and then towel dry
• Always clean in the direction of the grain of the Stainless Steel surface
• Use a soft brush or sponge (old tooth brush)
• Wipe over with a glass cleaner (Windex is very good)
• Polish with a metal polish paste (Autosol / Brasso)
• Use a Liquid cleaner (Bon-Ami or Jiff)

IT IS IMPORTANT TO NOTE THE FOLLOWING:

• NEVER use steel wool
• Beware of harsh liquid cleaners
• Beware of grit within cloths and mineral deposits within water
• Avoid prolonged exposure to acids from fruit, fruit juices, salts, spirits, bleach, tea-bags
• Avoid prolonged contact with ordinary steel such as tin cans or steel wool (rust stains may result)
• Do not keep harsh (acids or chlorine) chemicals under the sink / laundry tub
• Do not leave chlorine/chloride chemicals on the stainless steel surface
• Do not leave liquid soaps & cleaners to dry on stainless steel
• Do not use bleaches

AVOID SCRATCHES

Stainless steel can be scratched if
proper care is not taken during
installation.

CHECK CONDITION OF THE SINK

Inspect the sink for any visible
defects.

Do not install the sink if

defects are found.

Contact your

sink retailer/point of purchase.

CLAIMS FOR DAMAGE WILL NOT BE ACCEPTED AFTER INSTALLATION.

Any advice, recommendation, information, assistance or service provided by Oliveri Solutions in
relation to goods manufactured by it or their use and installation, is given in good faith and is believed
by Oliveri Solutions to be appropriate and reliable. However, any advice, recommendation,
information, assistance or service is provided by Oliveri Solutions without responsibility or liability.

IT IS HIGHLY RECOMMENDED THE ACTUAL SINK BE PRESENT WHEN THE

COUNTER/BENCHTOP IS CUT OUT AS A REFERENCE FOR ACCURACY

Downloadable cut-out template files and/or cut-out dimensions are available from our website.

MATERIALS FOR FITTING THE TOPMOUNT SINK:

•

Oliveri sink

including mounting clips, basket waste(s) and accessories (depending on model).

•

These installation instructions

•

Cut-out template and/or dimensions

(refer website)

•

Level

to check counter/benchtop and sink is installed level

•

Phillips head screwdriver

(#2 - to tighten mounting clips)

•

Flat head screwdriver

(large - to tighten basket wastes)

•

Suitable sealant

(neutral-cure silicone sealant or equivalent)

•

Additional mounting hardware

if fitting into thinner material. The clamps included with

the sink require a minimum counter/benchtop thickness of 25mm ( 1”). Different hardware or
packing materials will be needed for thin counter/benchtops.

Polished stainless steel will show scratches!

Scratches, rust or normal wear

and tear are not manufacturing faults and are not covered under warranty.

SPECIAL INSTRUCTIONS

Unequal bowl depths

Sinks that combine different sized bowls may also have unequal bowl

depth. Waste plumbing will need to accommodate this variance. All sinks have a height adaptor
included with the sink where needed.

Solitaire models

LR510 & LR515 may be top mounted, each using a circular cutout 466mm in

diameter. LR515 comes with a 32mm diameter taphole pre-cut in the tap landing. Mark the
location of this taphole when trial fitting the sink. Then, drillout the counter/benchtop in the
appropriate location so that the mixer tap can be solidly installed through both the sink and the
counter/benchtop. LR510 may also be under mounted in a solid-surface counter/benchtop using a
circular cut out 454mm in diameter after edges are smoothed. Refer Oliveri undermount
instructions for recommended installation methods.