Oliveri DZ112NTH - User Manual

SPECIAL INSTRUCTIONS FOR PARTICULAR TOP MOUNT SINK MODELS

CAUTION

Leave protective tape on the sink when inverting over a benchtop and tracing its shape. The stainless

steel will scratch if the sink slides across a hard surface.

Topmount sinks may also be known as “drop in” or “inset” sinks.

Topmount models with prefix PR, SN, NP, MO, DZ, PE, LL, UF, PL, MR, EL & TI.

These sinks will fit into standard 600mm bench tops.

Templates are available for download from www.oliverisinks.com

Download PDF template from www.oliverisinks.com. If the template is not available, the cutout shape may be created by

carefully inverting the sink onto the counter/benchtop and tracing around the perimeter.Cut the hole 10mm inside the traced line.

Many Oliveri sinks have waste outlets positioned to the rear of the bowls. Ensure the sink is correctly positioned when fitting.

Unequal bowl depth:

Sinks that combine different sized bowls may also have unequal bowl depth. Waste plumbing will need to

accommodate this variance.

All sinks have a height adaptor included with the sink where needed.

Solitaire models (LR)

LR510 & LR515 may be top mounted, each using a circular cutout 466mm in diameter. LR515 comes with a 32mm diameter

taphole pre-cut in the tap landing. Mark the location of this taphole when trial fitting the sink. Then, drillout the counter/benchtop

in the appropriate location so that the mixer tap can be solidly installed through both the sink and the counter/benchtop.

LR510 may also be under mounted in a solid-surface counter/benchtop using a circular cut out 454mm in diameter

after edges are smoothed. Refer Oliveri undermount instructions for recommended installation methods.

MATERIALS FOR FITTING THE UNDERMOUNT SINK:

•

Oliveri sink

(with correct tap holes as ordered) - includes mounting clips,

sealing gasket, basket wastes and other accessories (depending on

model).

•

These Installation Instructions

•

Level

to check counter/benchtop & sink is installed level

•

Phillips head screwdriver

(#2 to tighten mounting clips)

•

Flat head screwdriver

(large - to tighten basket wastes)

•

Suitable sealant

(neutral-cure silicone sealant or equivalent)

•

Masking material

to protect counter/benchtop and sink from excess

sealant

•

Additional Mounting Hardware

if fitting into thinner material. The

clamps included with the sink require a minimum counter/benchtop

thickness of 25mm / 1”.

INSTALLER - PLEASE READ & FOLLOW THESE

INSTALLATION INSTRUCTIONS

Please retain for consumer as care instructions are included

IT IS HIGHLY RECOMMENDED THE ACTUAL SINK BE PRESENT AT TIME OF CUTTING

Any advice, recommendation, information, assistance or service provided by Tasman Sinkware in

relation to goods manufactured by it or their use and installation, is given in good faith and is believed by

Tasman Sinkware to be appropriate and reliable. However, any advice, recommendation, information,

assistance or service is provided by Tasman Sinkware without responsibility or liability.

FOR “TOP MOUNT” OR “DROP IN” SINKS

CHECK MODEL

The model number on the sink

packaging must match the model

of sink the customer ordered.

Do not install if incorrect.

AVOID CUTS

The perimeter and punch-outs on

the sink may contain sharp edges.

Handle the sink carefully to avoid

personal injury.

CHECK THE CONDITION

Inspect the sink for any visible

defects.

Do not install the sink if

defects are found.

Contact your

sink retailer / point of purchase.

AVOID SCRATCHES

Stainless steel can be scratched

if proper care is not taken during

installation.

Download cutout

template files

(PDF, DWG & DXF)

from our website.

AUSTRALIA

Head Office &

Manufacturing Plant

Tasman Sinkware Pty Ltd

Regency Park SA

Phone: +61 8 8348 6444

Fax: +61 8 8348 6495

Email: [email protected]

oliveri.com.au

© Tasman Sinkware

TF 08f

May 2017