Page 3 - FCC WARNING; the receiver is connected.
FCC WARNING You are cautioned that changes or modifications not expressly approved by the party responsible for compliance could void your authority to operate the equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may...
Page 4 - Contents
◆ Contents ◆ Name of Parts ............................... 2 Power .............................................. 6 Computer Connection ................... 8 Paper Setting ................................. 9 Ribbon Setting ..........………….. 11 Does not print correctly .............. 13 When error lig...
Page 5 - Name of Parts; Front View; “When error light is ON”.
Name of Parts ■ Front View Top cover Paper check window Operation switch Power switch Front cover ■ Top cover .................... Open this cover when you set the paper. ■ Power switch .............. Press this switch to turn ON/OFF the printer. ■ Paper check window ... To check the status of paper...
Page 6 - Back View; remove the Top Cover and release.
Back View Fanfold paper set in place I/F Cover Optional interface Connecter Power Connector ■ Power Connector ... Connects AC adapter. ■ Optional interface Connecter ... Connects computer. ■ Fanfold Paper set in place ... Open this to use fanfold paper.To open the folder, remove the Top Cover and re...
Page 7 - Top Cover Open; adjust the width according to the paper size.
■ Top Cover Open Thermal head Driver for darkness adjustment Paper holder Head Sensor Paper holder slide lever Platen roller Head Open/Close lever ■ Paper holder ... When you use a roll paper, set the paper here. You can adjust the width according to the paper size. ■ Paper holder slide lever .. Pre...
Page 8 - Front Cover Open; Error number display; .. You can finely adjust the darkness that; Sensor level
■ Front Cover Open Error number display Print darkness adjustment volume Sensor level DIP-SW ■ Print darkness adjustment volume .. You can finely adjust the darkness that is set in the Printer Setting screen. See the manual for details. ■ Sensor level ...... Do not use this. Only for used by service...
Page 9 - Power; Cable Connection
Power Cable Connection 1 Connect the power cable with the main unit and AC adapter as shown in the figure. When you insert the AC adapter in the main unit, set the stopper firmly. 2 Plug in the power cable to the outlet. 3 Use a Two-prong adapter if only a two-prong outlet is available. 1 Connect th...
Page 10 - Power Switch; * When you turn on the power, the POWER light lights up. Please confirm
Power Switch Power Switch Press the power switch at the front side of the main unit in the “|” direction. * When you turn on the power, the POWER light lights up. Please confirm this. When you turn off the printer, flip the switch to the “ ” direction. 7
Page 11 - Computer Connection; Connection example using Bi-directional parallel interface; its “Optional Interface”.
Computer Connection Connection example using Bi-directional parallel interface Use [Bi-directional parallel interface(sold separately)]. This printer operates by being connected to a computer. Turn off the power of the printer and connect to the computer with an interface cable connecting the bi-dir...
Page 12 - Paper Setting; Press the Head Open/Close lever to
Paper Setting 1 Confirm the [PUSH] mark on the Left/Right side of the main unit. While depressing the mark on the cover, open the Top cover 2 Press the Head Open/Close lever to the direction as shown in Figure. Confirm that the head is detached from the platen roller part, then lift the head in the ...
Page 14 - Ribbon Setting
Ribbon Setting Thermal Transfer model OKI POS T400/T410 only. 1 Confirm the [PUSH] mark on the Left/Right side of the main unit. While depressing the mark on the cover, open the Top cover. 2 Press the Head Open/Close lever to the direction as shown in Figure. Confirm that the head is detached from t...
Page 16 - Does not print correctly; Print error
Does not print correctly Print error • Paper set correctly? ➞ Please set the paper correctly. • Platen roller clean? ➞ If the platen roller is not clean, clean it using the Cleaning Kit (refer to the manual). • Paper replenished regularly? ➞ If the edge of the paper does not set regularly, the paper...
Page 17 - When error light is ON; Error light; Error Number Display
• Paper set correctly? ➞ Please confirm that the paper is set correctly. • Platen roller clean? ➞ If the platen roller is not clean, clean the platen roller using the Cleaning Kit (refer to the manual). • Thermal head clean? No label is adhered to the head? ➞ If the thermal head is not clean, clean ...
Page 18 - POWER light is not ON even if you turn on the machine.
Failure? Please confirm the following before you decide it’s a mechanical failure. POWER light is not ON even if you turn on the machine. AC adapter and power cable are plugged in the outlet correctly? ➞ Plug in AC adapter and power cable into the outlet correctly. AC adapter is plugged in to the ma...
Page 19 - AVERTISSEMENT DE LA FCC
AVERTISSEMENT DE LA FCC Les changements ou modifications qui ne sont expressément approuvés par la partie responsable d’assurer la conformité pourraient résilier votre droit d’utiliser l’équipement. Ce dispositif est conforme à la partie 15 de la réglementation FCC. Le fonctionnement est soumis aux ...
Page 20 - Contenu
Contenu Noms des pièces .............................. 2 Alimentation..................................... 6 Connexion ordinateur....................... 8 Réglage papier.................................. 9 Réglage du ruban............................ 11 Impression incorrecte .................... 13 ...
Page 21 - Noms des pièces; Vue avant; Couvercle supérieur; Commutateur de fonctionnement
2 Noms des pièces ■ Vue avant ■ Couvercle supérieur ........ Ouvrez ce couvercle quand vous réglez le papier. ■ Commutateur d’alimentation ......... Appuyez sur ce commutateur pour allumer et éteindre l'imprimante. ■ Fenêtre de vérification papier ....... Pour vérifier l’état du papier. ■ Couvercle ...
Page 22 - Vue arrière; Connecteur d’alimentation
3 Vue arrière ■ Connecteur d’alimentation ........ Connecte l’adaptateur CA. ■ Connecteur d’interface optionnel ........... Connecte l’ordinateur. ■ Papier en accordéon installé en place ..... Ouvrez pour utiliser du papier en accordéon. Pour ouvrir la plieuse, retirez le couvercle supérieur et relâ...
Page 23 - Ouverture du couvercle supérieur
4 ■ Ouverture du couvercle supérieur Tête Rouleau de platine Levier d’ouverture/de fermeture de tête ■ Support de papier ....... Quand vous utilisez du papier en rouleau, réglez le papier ici. Vous pouvez régler la largeur selon le format papier. ■ Levier de coulissement de support de papier ...... ...
Page 24 - Ouverture du couvercle avant; Volume de réglage de densité d’impression; Affichage du numéro d’erreur
5 ■ Ouverture du couvercle avant Affichage du numéro d’erreur Degré de réglage de densité d’impression Niveau du capteur DIP-SW ■ Volume de réglage de densité d’impression ....... Vous pouvez régler avec précision la densité paramétrée dans l‘écran Printer Setting. Voyez le manuel pour les détails. ...
Page 25 - Alimentation; Connexion du câble
6 Alimentation Connexion du câble 1 Branchez le câble d’alimentation dans l’unité principale et l’adaptateur CA comme montré dans la figure. Quand vous insérez l’adaptateur CA dans l’unité principale, réglez la butée fermement. 2 Branchez le câble d’alimentation dans la prise murale. 3 Utilisez un a...
Page 26 - Commutateur d’alimentation
7 - Commutateur d’alimentation Commutateur d’alimentation - Appuyez sur le commutateur d’alimentation à l’avant de l’unité principale dans la direction “|”.* Quand vous mettez sous tension l’unité, le témoin POWER s’allume. Veuillez le confirmer. - Quand vous éteignez l’imprimante, basculez le commu...
Page 27 - Connexion à l’ordinateur
8 Connexion à l’ordinateur L’exemple de connexion illustre une interface parallèle bidirectionnelle Utilisez une [interface parallèle bidirectionnelle (vendue séparément)]. Pour fonctionner, l’imprimante doit être raccordée à un ordinateur. Mettez hors tension l’imprimante et connectez-la à un ordin...
Page 28 - Réglage papier
9 Réglage papier 1 Confirmer la marque [PUSH] sur le côté gauche/droit de l’unité principale. Tout en enfonçant la marque, ouvrez le couvercle supérieur 2 Appuyez sur le levier d’ouverture/de fermeture de la tête dans la direction indiquée dans la figure. Confirmer que la tête est détachée du galet ...
Page 30 - Réglage du ruban
11 Réglage du ruban Modèle à transfert thermique OKI POS T400/T410 seulement. 1 Confirmer la marque [PUSH] sur le côté gauche/droit de l’unité principale. Tout en enfonçant la marque, ouvrez le couvercle supérieur 2 Appuyez sur le levier d’ouverture/de fermeture de la tête dans la direction indiquée...
Page 33 - Quand le témoin d’erreur est allumé
14 • Papier installé correctement? Confirmez que le papier est réglé correctement. • Galet de platine propre? Si le galet de platine n’est pas propre, nettoyez avec le galet de platine avec une trousse de nettoyage (voir le manuel). • Tête thermique propre? Étiquette collée à la tête? Si la tê...