Novatel GM-14915095 - Manual
Novatel GM-14915095 – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.
Table of Contents:
- Page 2 – BOTTOM VIEW
- Page 3 – Oscillator
- Page 4 – OEM6 Family Installation and Operation User Manual; TOP VIEW
- Page 5 – OV; Establishing a New Receiver Connection; OEM6 Family
- Page 6 – Tracking Satellites Indicator
- Page 7 – Entering Commands; Console; NABLING; SBAS; OEM6 Family Firmware Reference Manual
- Page 8 – Refer to the
- Page 10 – ETHERNET CONNECTION; at; POST PROCESSING; Products; DATA LOGGING; An extensive set of logs are available to capture data (refer to the
- Page 11 – ONBOARD MEMORY; OEM6 Family Installation and; Additional Functionality
- Page 12 – QUESTIONS OR COMMENTS; Quick Start Guide - OEM6 Family Cards
1
OEM6
®
Family
GM-14915095
Rev 7
January 2015
QUICK START GUIDE
This guide provides the basic information needed to set up and begin using a NovAtel
®
OEM6
®
family
card.
USER MANUALS
•
For more information on the installation and operation of the NovAtel receiver, download
the
OEM6 Family Installation and Operation User Manual
(OM-20000128).
•
For information on the logs and commands used to configure the NovAtel receiver,
download the
OEM6 Family Firmware Reference Manual
(OM-20000129).
Both manuals are available from:
www.novatel.com/support/firmware-software-and-manuals/product-
manuals-and-doc-updates/oem6-family
BOX CONTENTS
•
OEM6 receiver card and Quick Start Guide
Additional Equipment Required
For the receiver to perform optimally, the following additional equipment is required.
•
The receiver card power supply is dependent on the card purchased. Refer to the
Installation and Operation User Manual
(OM-20000128) Technical Specification sections for
OEM615, OEM617, OEM617D, OEM628 and OEM638 power requirements
•
An enclosure to protect against environmental conditions and RF interference
•
A wiring harness to provide power to the receiver and access to serial, GPIO, PPS, Event, USB,
CAN, Ethernet and other signals
•
A serial, USB or Ethernet cable
•
A high quality GNSS antenna or antennas (model dependent), such as NovAtel’s GPS-703-GGG
(refer to
www.novatel.com/products/gnss-antennas
for options)
•
A 50 ohm antenna cable with a male MMCX (OEM617D, OEM628 and OEM638) or MCX
(OEM615 and OEM617) connector at the receiver end
•
Microsoft Windows computer
•
ESD wrist strap
•
Optional NovAtel OEM6 Development Kit (01018849) - (
contact www.novatel.com/support
for instructions on using the OEM6 Development Kit with the OEM638 receiver card)
If a SPAN
®
GNSS+INS capable receiver was purchased, download the
(GM-14915112). If you wish to purchase SPAN firmware, contact
[email protected] to purchase SPAN software functionality for your receiver.
"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.
Summary
2 OEM6 FAMILY CARDS Figure 1: OEM615 Connectors and Indicators Figure 2: OEM617 Connectors and Indicators BOTTOM VIEW TOP VIEW LED Status Indicator J1101 Power/data/signal connector J101 RF signal IN/LNA power OUT BOTTOM VIEW TOP VIEW LED Status Indicator J1101 Power/data/signal connector J101 RF si...
3 Figure 3: OEM617D Connectors and Indicators Figure 4: OEM628 Connectors and Indicators BOTTOM VIEW TOP VIEW LED Status Indicator J1101 Power/data/signal connector Primary RF signal IN/LNA power OUT Secondary RF signal IN/LNA power OUT TOP VIEW BOTTOM VIEW P1500 power, data and signaling P1502 CAN/...
4 Figure 5: OEM638 Connectors and Indicators SETTING UP AN OEM6 FAMILY CARD Complete the following steps below to connect and power the OEM6 family card. 1. Install the OEM6 family card and the wiring harness in a secure enclosure to reduce environmental exposure, RF interference, and protect agains...
