Netgear WN802Tv2 - Manual

)NSTALLATION'UIDE

NETGEAR Wireless-N Access Point WN802Tv2

Start Here

Follow these instructions to set up your wireless-N access point

.

You can also consult the

documentation links on the

Resource CD

or the NETGEAR knowledge base at

http://kbserver.netgear.com. Please consult the

Resource CD

or the Documentation link on

the user interface to access the

Reference Manual

for instructions on advanced

configuration options.
Estimated Completion Time: 20 minutes.

Tip

: Before mounting the WN802Tv2 Wireless-N Access Point in a high location, first set

up and test the WN802Tv2 to verify wireless network connectivity.

First, Set Up the WN802Tv2

1. C

ONNECT

THE

W

IRELESS

-N A

CCESS

P

OINT

T

O

Y

OUR

C

OMPUTER

a.

Unpack the box and verify the contents.

b. Prepare a computer with Internet access and an Ethernet adapter. If this computer

is already part of your network, record its TCP/IP configuration settings.
Configure the computer with a static IP address of 192.168.0.210 and
255.255.255.0 as the Subnet Mask.

c.

Connect an Ethernet cable from the
WN802Tv2 to the PC.

d. Securely insert the other end of the cable

into the WN802Tv2 Ethernet port.

e.

Connect the NETGEAR Switching
Power Supply from the wireless-N
access point to an AC power outlet.

Note:

Only connect your wireless-N

access point using the switching power
supply provided with the WN802Tv2.

f.

Check the lights on the front of the wireless-N access point:

•

Power

: The green power light should be

lit. If the power light is not lit, check the
connections and check to see if the power
outlet is controlled by a wall switch that is
turned off.

•

Ethernet

: The Ethernet (LAN) light

should be lit (amber for 10/100 Mbps and green
for 1000 Mbps) indicating that a connection
has been made. If not, make sure the Ethernet
cable is securely attached at both ends.

•

WLAN:

The blue wireless light should

be lit and blinking indicating that it is sending a
signal.

2. C

ONFIGURE

LAN

AND

W

IRELESS

A

CCESS

a.

Configure the WN802Tv2 Ethernet port for LAN access.Connect to the
WN802Tv2 by opening your browser and entering

http://192.168.0.233

in the

address field.

A login window will display.

b. When prompted, enter

admin

for the

user name and

password

for the

password, both in lower case letters.
The NETGEAR Wireless-N Access
Point WN802Tv2 user interface will
display.

c.

Select Wireless Settings under the
Setup menu on the left navigation pane and configure your wireless interface for
wireless access.

d. Then select WEP/WPA Settings under Security and configure the level of data

encryption security for your network.
See the online help or the online Reference Manual for full instructions.

http://192.168.0.233

e.

Finally, select Basic Settings under the Setup menu on the left navigation pane
and configure the IP Settings for your network.

Note:

If you change the default subnet of the LAN IP address, you will be

disconnected from the WN802Tv2 Wireless-N Access Point user interface. To
reconnect, reconfigure your computer with a static IP address within the new
LAN IP subnet.

Tip:

Before you deploy your wireless-N access point, reserve an IP address

(based on the WN802Tv2’s MAC address) on the DHCP server. That way, you
can configure the wireless-N access point with a static IP address which you can
always use to log in to make future configuration changes.

3. T

EST

WIRELESS

CONNECTIVITY

Using a computer with a wireless adapter configured according to the wireless
settings you just set in the WN802Tv2, establish a wireless connection to the
WN802Tv2.

Deploy the WN802Tv2

Now that you have finished the setup steps, you are ready to deploy the WN802Tv2 in
your network. If needed, you can now reconfigure the PC you used in step 1 back to its
original TCP/IP settings.

Warning:

To allow for proper ventilation, always install the unit vertically using the

included stand. Do not lay the unit flat.
1. Disconnect the WN802Tv2 from the computer and place it where you will deploy it.

The best location is elevated, such as wall mounted or on the top of a cubicle, at the
center of your wireless coverage area, and within line of sight of all the mobile
devices. The WN802Tv2 should be positioned vertically.

2. Connect an Ethernet cable from your WN802Tv2 wireless-N access point to a LAN

port on your router, switch, or hub.

3. Connect the power adapter to the wireless-N access point and plug the power adapter

in to a power outlet. The Power, WLAN and Ethernet lights should light up.

Note:

A wall mount kit is included with theWN802Tv2. Instructions for installing the

brackets and mounting the WN802Tv2are in the online

Reference Manual

.