NEC NP01WK - Manual

ENG-4 ENG-5 Preparation  Packaged Parts Please check the packaged items. Wall adapter:1 Arm:1 Projector adapter:1 Wall plate:1 *1 M5 screws:4 *2 *1, *2:To be used when mounting the wall adapter in the North America region. Cover (A, B):2 pairs Arm cover:1 Plate (B):1 M4 screws:4M3.5 screws:2 Hex wr...

ENG-4 ENG-5 Vertical adjust/ Arm fixation knobs Arm cover Elongate hole for screw (or bolt) (4 parts) Covers (A, B) Plate (A) Arm fixation screw Grooves for wiring Arm Tilt adjust knobs (4 parts) Central axis Wall adapter Cover (B, A) Projector adapter Projector fixation plate Horizontal adjust scre...

ENG-6 ENG-7  Dimensions of Parts: (unit: mm) The dimensions of the positions of the wall fixation screws (bolts) of the wall adapter are described. 142 100 100 142 100 100 189 90 - 190 189 219 120 320 280 Projector bottom surface (including the feet) 533 (minimum) -733 (maximum) The center of the w...

ENG-6 ENG-7 Mounting the Projector Preparations 1. Determine the installation location of the screen, and accordingly decide the installation position of the wall mount unit. Refer to the section "Installation" in the user’s manual included with the projector for more information. • Installa...

ENG-8 ENG-9 c Align the projector adapter with the holes on the bottom of the projector and securely attach the adapter with the four supplied screws (M4x20). d Loosen the vertical adjust/arm fixation knobs of the projector adapter. Caution Do not try to attach the projector adapter without the foam...

ENG-8 ENG-9 b a 3. Attach the arm to the wall adapter. a Loosen the arm fixation screws (top and bottom) with the supplied hex wrench. b Insert the arm plate (A) into the wall adapter from the top and tighten the screws (top and bottom) near the center of the elongated hole. * The covers (A) and (B)...

ENG-10 ENG-11 5. Cabling a The power cord and signal cables can be passed through the grooves for wiring on the left and right side of the arm. This should be done before attaching the arm cover. Take care not to squeeze the cables with the horizontal adjust screws. This concludes the projector inst...

ENG-12 ENG-13 Adjusting the Projection Position  Preparations Before adjusting • Project an image from the projector, then first use the focus lever of the projector to roughly adjust the focus of the projected image. For information on how to project an image, see “Installation” in the user’s manu...

ENG-12 ENG-13 d c c Turn the left or right knob to adjust projector tilt in the left or right direction. - When the knob shown in black in the illustration i s t i g h t e n e d , t h e p r o j e c t o r i s r o t a t e d i n t h e counterclockwise direction. d When the adjustment is complete, tight...

ENG-14 ENG-15 4. Adjust the tilt. Tilt adjustment is performed with the four adjustment knobs.  Front/rear tilt adjustment Adjust together Rotation axis Adjust together Rotation axis  Left/right tilt adjustment Fine adjustment in same direction as for vertical adjustment • If tilt adjustment achie...

ENG-14 ENG-15 5. Attach the covers to the projector adapter and the wall adapter. a Attach cover (A) (with hook) and cover (B) (with notch) to the upper side of the wall adapter. Slide the two covers towards the center while pushing them down, as shown in the illustration. The bottom of each cover w...

ENG-16 Specifications Product name: Wall mount unit Model: NP01WK/NP01WK1 Adjustment angle: Up-down angle ±3°, left-right angle ±3°, inclination angle ±10° Adjustment width: Front-rear ±100 mm, left-right ±50 mm, up-down ±50 mm External dimensions: 280 (W) x 541(D) x 219 (H) mmWeight: Approx. 6.2kg ...