NEC DT400 User Manual - Free PDF Download

Page 2 - Note

This key is used to turn over the page of 8LD display. Status of the Line key such as Call termination, Call Hold or Busy, and setting on the Feature key are shown as Icons. 32 (8 keys x 4 pages) additional programmable keys are provided. (6) Help Explanations of the Soft Keys can be called up on th...

Page 3 - Programmable Keys; To Register Name On Speed; Controls the build-in speaker which can be used for Hands Free

Programmable Keys These keys can be programmed as “Speed Dial key” on the programmable keys, users can assign any numbers (ex. Telephone number, etc.) to the key (up to 24 digits). * Users can register name on each Speed Dial key. For the procedures, refer to To Register Name On Speed Dial key . (10...

Page 4 - Feature; Terminal Setup with the Up/Down Key; To Adjust Handset Receiver Volume; When the terminal is connected with 16LD ADM, 16 degrees of

(18) Transfer Allows the station user to transfer established calls to another station, without attendant assistance. (19) Hold Press this key to place a call on hold. Pressing twice lock held call to this station. . This describes operating procedures for terminal settings by the UP/Down Key and Fe...

Page 5 - Terminal Setup with the Feature Key; To Select Ringer Tone; RINGER TONE

Terminal Setup with the Feature Key Microphone On/Off LED on Mic key shows the status of the built-in microphone. … Press Soft Key associated with the MIC Display or press Feature and 1 . To Select Ringer Tone (1) Press the MENU key (2) Go to SETTING (3) [1] User Setting (4) [1] Incoming Call (5) [4...

Page 6 - Multiline Appearance; To Originate a Call

To Originate an Outside Call … Lift handset or press Speaker key, receive dial tone. … Dial the Central Office access code, 9 . … Dial desired telephone number. … Use handset or MIC to start a conversation. Display indicates: To Originate an Internal Call … Lift handset or press Speaker key. … Recei...

Page 7 - To Place a call on HOLD; To Retrieve; To Place a Call on Exclusive Hold; Held station number

To Place a call on HOLD Press Hold . Held line wink flashes. Held station number HOLD 1212 4:26 PM TUE 13 APR 2020 [ Voice ][ Headset ][ Release ] Note: If held line appears on other DT Series stations, the associated LED flashes red slowly. To Retrieve … Lift handset or press Speaker key. … Press h...

Page 8 - Recall; Exclusive Hold excludes any other phone from picking up; To Transfer a Call; To Conference a call; TRANSFER; Transfer; CONF; Last; When Station Within Pickup Group Rings; PICK UP

… After preprogrammed time, Automatic Recall is initiated. … Visual and audible signal (rapid flash and ring burst) is sent to station which placed call on Exclusive Hold. Recall shows as a flashing green LED on your phone, and solid red on other phones with same line. Note: Exclusive Hold excludes ...

Page 9 - SPEED SET; To Register Name On OneTouch Speed Dial key; Alphabetic character; Digit

Number Redial To Recall The Last Number Dialed Press Redial. The Last Number is displayed. Press Redial to scroll through the last 5 numbers dialed. Press *. The number dialed will be redialed and displayed. NOTE: Each time the Redial key is pressed the numbers dialed are displayed sequentially. To ...

Page 10 - Call Forwarding-All Calls; FORWARD XXXX; FORWARD XXXX

Call Forwarding-All Calls To Set Press Speaker key or lift handset. Receive dial tone. Press CF-AllCalls key. Receive special dial tone. Dial destination station or 9 and the outside telephone number. Receive service set tone. CF-AllCalls LED lights Press Speaker key or hang up. Call Forwarding for ...

Page 11 - To Save And Repeat A Number; To Save

To Save And Repeat A Number To Save Press Speaker key or lift handset. Dial desired telephone number. Press >>>, press S&R key. Dialed number is now Stored. Press Speaker key or lift handset. Press S&R key. Phone automatically redials the programmed number. NOTE: If saved number is ...