Nady MGT16 - Manual - manualsarea.com

Page 2 - Auto-Sync Channel transfer for quick, convenient; Using This Manual

Contents 2 Introduction ............................................................................................................................. 2 Using this Manual .................................................................................................................... 2 System Feat...

Page 3 - System Features; MGT-16 system Features

System Features MGT-16 system Features UHF wireless system for guitar/bass • 16 user-selectable PLL frequencies • for interference-free operationUp to 250’ operating range, line-of-sight • Infrared ASC • ™ Auto-Sync Channel transfer from receiver to transmitter for instant setupBattery operated rece...

Page 4 - Quick User Controls Guide; MGT-16 Instrument receiver

4 Quick User Controls Guide MGT-16 Instrument receiver POWER ACT 10 13 14 11 12 2 1 3 6 5 15 IR PO LO RX LEVEL CHANNEL 1 2 3 4 SQ OFF ON 7 8 9 16 4

Page 7 - Ir sync selected Frequency Download; System Operation; MGT-16 wireless Instrument receiver; The MGT-16 receiver is supplied with; Powering the receiver; For DC operation, open the receiver’s

7 Ir sync selected Frequency Download from MGT-16 receiver to MT-16a/r Transmitter (1) ASC ™ IR SYNC INFRARED LED WINDOW For downloading selected Channel (Frequency) to transmitter (21) IR RECEPTOR SENSOR/WINDOW Infrared LED sensor for linking the TX to the RX during IR frequency download. 14. ASC ™...

Page 8 - adjusting the squelch; rF signal; selecting the MGT-16 receiver; Selection Chart; Ir synch

powers the unit and will not charge NiMH rechargeable batteries if installed. For battery operation the AC adapter must be disconnected. Note: For quietest optimal performance, use the AC/DC adapter as battery operation raises the noise floor around 4 dB. Generally this is only a concern when playin...

Page 9 - Frequency select DIP; Connecting audio Output; audio Output Jack; Powering the Transmitter; Internal audio

9 When the rF signal leD (10) on the receiver lights up, the system frequency is properly synchronized. To change to a different frequency, reset the Frequency select DIP switches (4) and sync the transmitter again to the new selected frequency first, after turning the transmitter off and then on ag...

Page 10 - to the selected Channel; Selecting the MGT-16; Instrument Transmitter; Connecting Audio; Transmitter Power switch

10 trim-pot counterclockwise reduces overall system audio output (thus lowering distortion but raising background noise), while turning clockwise increases overall system audio output (thus lowering background noise but raising distortion). The Audio Level Adjust is factory set to the mid position, ...

Page 11 - Specifications

11 Specifications MGT-16 sysTeMFrequency response 50Hz–16kHz (-3dB) Dynamic range 120dB Oscillating system Phase Lock Loop (PLL) Total Harmonic Distortion (THD) <0.8% rF Carrier Frequency range 902.40MHz–923.70MHz Modulation FM (F3E), +/-30KHz normal Operating range Up to 250 feet (typical, depen...

Page 12 - Cautions and Troubleshooting; no or low audio; on the MGT-16 receiver is not in the second; rF Interference and Finding Open Channels; Adjusting the

Cautions and Troubleshooting 12 no or low audio If you are not getting audio through the system, carefully re-check all setups. Especially note that the receiver and transmitter must be set to operate on the same RF channel. Make sure that the receiver Power switch (2) on the MGT-16 receiver is not ...

Page 13 - Miscellaneous Tips; The receiver antennas should be kept

13 Miscellaneous Tips The receiver antennas should be kept • away from any metal surfaces whenever possible as they can reflect away or shield the incoming RF signal.When inserting batteries, make sure they • are inserted with the correct polarity. Before operation, confirm that the receiver • and a...

Page 14 - Frequency Selection Chart; Channel selection Frequency; Accessories; Part number; 0VDC/200mA AC/DC receiver power supply adapter included; Service Information; Do not attempt to service this unit yourself as

14 MGT-16 DIP-Switch Frequency Selection Chart Frequency Plan: 902.4MHz-923.7MHz (16 Channels) u.s. Channel selection Frequency 9 913.9 10 914.0 11 916.0 12 917.9 13 919.7 14 920.0 15 921.1 16 923.7 Channel selection Frequency 1 902.4 2 904.8 3 905.4 4 906.7 5 907.8 6 909.8 7 910.8 8 911.2 1 2 3 4 1...

Page 15 - One-Year Limited Warranty; This warranty is subject to the following conditions:

15 One-Year Limited Warranty Nady Systems, Inc. warrants to the original consumer purchaser that the unit is free from any defects in material or workmanship for a period of one year from the date of original retail purchase. If any such defect is discovered within the warranty period, Nady Systems,...

Nady MGT16 - Manual

Table of Contents:

Summary

Other Nady Models