MTD L-Style - Manual

7 Attaching the Chute Assembly and Directional Control 1. Apply a lubricant (i.e. 3-in-1 oil) to the rim of the chute base (and the underside of the chute assembly) and position the chute assembly over the base. 2. Close the flange keepers to secure the chute assembly to the chute base. The flange k...

8 SECTION 3: KNOW YOUR SNOW THROWER WARNING: Read, understand, and follow all instructions and warnings on the machine and in this manual before operating. NOTE: For detailed starting instructions and more information on all engine controls, refer to the Tecumseh Engines manual packed separately and...

9 Auger Control The auger control is located on the left handle. Squeeze the control grip against the handle to engage the augers and start snow throwing action. Release to stop. Drive Control The drive control is located on the right handle. Squeeze the control grip against the handle to engage the...

10 SECTION 4: OPERATING YOUR SNOW THROWER Before Starting WARNING: Read, understand, and follow all instructions and warnings on the machineand in this manual before operating. Gas & Oil Fill-Up Service the engine with gasoline and oil as instructed in the Tecumseh Engines manual packed separate...

11 IMPORTANT: Do not release the handle and allow it to snap back. Keep a firm hold on the starter handle and allow it to slowly recoil. • As the engine warms, slowly rotate the choke control to the OFF position. If the engine falters, quickly rotate the choke control back to the FULL position and t...

12 • Confirm that the auger has completely stopped rotating and shows NO signs of motion. IMPORTANT: If the auger shows ANY signs of rotating, immediately return to the operator’s position and shut off the engine. Wait for ALL moving parts to stop before re-adjusting the auger control. • To readjust...

13 SECTION 5: MAKING ADJUSTMENTS WARNING: Never attempt to make any adjustments while the engine is running,except where specified in operator’s manual. Shift Rod Adjustment If the full range of speeds (forward and reverse) cannot be achieved, refer to the figures marked 1,2, and 3 to the right and ...

14 Drive Control When the drive control is released and in the disengaged “up” position, the cable should have very little slack. It should NOT be tight. Check the adjustment of the drive control as follows: 1. With the drive control released, push the snow thrower gently forward. The unit should ro...

15 SECTION 6: MAINTAINING AND SERVICING YOUR SNOW THROWER WARNING: Before lubricating, repairing, or inspecting, disengage all controls and stop engine. Wait until all moving parts have come to a complete stop. Always wear safety glasses during operation or while performing any adjustments or repair...

16 Auger Belt Replacement To remove and replace your snow thrower’s auger belt, proceed as follows: 1. Remove the plastic belt cover on the front of the engine by removing the two self-tapping screws. • Drain the gasoline from the snow thrower, or place a piece of plastic under the gas cap. • Carefu...

17 Drive Belt Replacement To remove and replace your snow thrower’s auger belt, proceed as follows: 1. Remove the plastic belt cover on the front of the engine by removing the two self-tapping screws. • Drain the gasoline from the snow thrower, or place a piece of plastic under the gas cap. • Carefu...

18 Friction Wheel Removal If the snow thrower fails to drive with the drive control engaged, and performing the drive control cable adjustment on page 14 fails to correct the problem, the friction wheel may need to be replaced. Follow the instructions below. Examine the friction wheel for signs of w...

20 SECTION 8: TROUBLE SHOOTING GUIDE NOTE: For repairs beyond the minor adjustments above, contact your local authorized service dealer. Trouble Possible Cause(s) Corrective Action Engine fails to start Fuel tank empty, or stale fuel. Blocked fuel line.Choke control not in ON positionFaulty spark pl...

22 1* 9 48 3 25 15 8 28 66 35 40 5 30 21 10 7 22 13 18a 18b 16 56 58 57 55 26 4 24 6 41 15a 15b 54 2 49 53 52 51 14 64 60 65 61 62 63 50 36 43 44 45 42 37 38 46 11 31 32 14 33 23 29 27 12 34 39 59 20 47 17 19 SECTION 9: PARTS LIST * K-Style

MANUFACTURER’S LIMITED WARRANTY FOR: The limited warranty set forth below is given by MTD LLC with respect to new merchandise purchased and used in the United States, its possessions and territories. “MTD”warrants this product against defects in material and workmanship for a period of two (2) years...