Moxa EDS-828 - Manual - manualsarea.com

Page 6 - Uninstalling IM-2G Modules

5 STEP 2 : Mounting the EDS-728/828 on the wall requires 4 screws to ensure that the switch does not come loose from the wall. Use the switch, with wall mounting plates attached, as a guide to mark the correct locations of the 4 screws. The heads of the screws should be less than 6.0 mm in diameter,...

Page 7 - Wiring Requirements; Grounding Moxa EtherDevice Switch; Wiring the Relay Contact

6 Wiring Requirements WARNING Safety First! Be sure to disconnect the power cord before installing and/or wiring your Moxa EDS-728/828. Calculate the maximum possible current in each power wire and common wire. Observe all electrical codes dictating the maximum current allowable for each wire size. ...

Page 8 - Wiring the Redundant Power Inputs

7 RELAY1 RELAY2 PWR1 PWR2 V2+ V2- V1+ V1- D I 1 I 1 I 2 D I 2 Top View Front View FAULT : The two sets of relay contacts of the 6-pin terminal block connector are used to detect user-configured events. The two wires attached to the Fault contacts form an open circuit when a user-configured event is ...

Page 9 - Communication Connections; 000BaseT Ethernet Port Connection

8 Communication Connections The pinout and cable wiring diagrams in this section show how the ports on the EDS-728/828 connect to other devices: Pinouts are diagrams that indicate the type of signal passing through each of the port’s pins. NOTE 1. The pin numbers for male DB9 and DB25 connectors, an...

Page 10 - LED Indicators

9 MDI/MDI-X Port Pinouts Pin Signal 1 TRD(0)+ 2 TRD(0)- 3 TRD(1)+ 4 TRD(2)+ 5 TRD(2)- 6 TRD(1)- 7 TRD(3)+ 8 TRD(3)- 1 8 100/1000Base Fiber Port Connection The concept behind the duplex port and cable is quite straightforward. Suppose you are connecting devices I and II. Contrary to electrical signal...

Page 12 - Specifications

11 Fast Ethernet Module LEDs On Power is being supplied to the interface module. PWR GREEN Off Power is not being supplied to the interface module. P1/P2/ P3/P4 GREEN On/ Off/ Blinking Displays the module port’s status by mode. Gigabit Ethernet Module LED P1/P2 GREEN On/ Off/ Blinking Displays the m...

Page 13 - Gigabit Ethernet Interface Module, IM-2G Series

12 Digital Inputs Two inputs with the same ground, but electrically isolated from the electronics. x For state “1”: +13 to +30V x For state “0”: -30 to +3V x Max. input current: 8 mA Power Input Voltage 24 VDC (12 to 45 VDC), redundant dual inputs Connection Two removable 6-pin terminal blocks Power...

Page 14 - Fast Ethernet Interface Module, IM series

13 Optical Fiber/SFP-1GxxxLC Series SX LX LHX ZX Wavelength 850 nm 1310 nm 1310 nm 1310 nm Max. Tx -4 dBm -3 dBm 1 dBm +5 dBm Min. Tx -9.5 dBm -9.5 dBm -4 dBm 0 dBm Rx Sensitivity -18 dBm -20 dBm -24 dBm -24 dBm Link Budget 8.5 dB 10.5 dB 20 dB 24 dB Typical Distance 550m (a) 275m (b) 1100m (c) 550m...

Page 16 - Moxa Internet Services

15 IM-2MST/2TX 250 g IM-2SSC/2TX 245 g IM-1LSC/3TX 235 g IM-4MSC 250 g IM-4MST 270 g IM-4SSC 270 g Environmental Operating Temperature 0 to 60°C (32 to 140°F) Storage Temperature -40 to 85°C (-40 to 185°F) Ambient Relative Humidity 5 to 95% (non-condensing) Regulatory Approvals Safety UL60950-1, CSA...

Moxa EDS-828 - Manual

Table of Contents:

Summary

Other Moxa Models